Search NASA⌕ Search

SEARCH · Search NASA

Results for “oxynitrides”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Creating Functional Oxynitride–Silicon Interfaces and SrNbO 2 N Thin Films for Photoelectrochemical Applications

Photoelectrochemical performance dependence upon absorption length, carrier diffusion length, and surface area of an oxynitride photoabsorber is investigated. How best to fabricate optical-quality thin films of bandgap-tunable oxynitrides is also discussed. We targeted the stoichiometric compound SrNbO 2 N as an optimal wide-bandgap photoabsorber (1.9 eV) for use with silicon (1.1 eV) in a tandem structure photoelectrochemical cell. Preparation of perovskite oxynitrides at high-temperature as isolated powders is often straightforward, but it is difficult to integrate them as thin films in tandem junction devices with low-temperature materials. Here we develop the first method to prepare optical-quality SrNbO 2 N thin-films of tunable thickness and roughness on single-crystal silicon substrate. This achievement required an interfacial layer of ultra-thin TaN to be used as a barrier to reduce the inter-diffusion of silicon and oxygen during oxynitride syn-thesis. We produced a variety of SrNbO 2 N film thicknesses (20-440 nm) on n + -Si(100) surfaces. Roughness factor (0.14-21) scaled with thickness. The intrinsic photoelectrochemical activity of these devices was evaluated using a low-barrier sacrificial electron donor. Photocurrent density and photovoltage revealed a significant (and non-linear) dependence on film thickness and roughness. Furthermore, absorption length, carrier diffusion length, and surface area were each found to play key roles. Balancing these is required for optimally performing devices.

08 HYDROGEN↗
DOE OSTI2022

Semi Transparent Three-Dimensional Macroporous Quaternary Oxynitride Photoanodes for Photoelectrochemical Water Oxidation

Semi transparent three-dimensional macroporous (3DM) photoanodes based on quaternary oxynitrides have the potential to simultaneously realize superior light harvesting and efficient charge transfer in a tandem photoelectrochemical (PEC) cell. A 3DM CaTaO 2 N photoanode was prepared for the first time on a GaN/Al 2 O 3 substrate via a chemical route, and it exhibits a high transmittance of >60% in the wide solar spectrum and a photoresponse onset at −0.3 V versus the reversible hydrogen electrode (V RHE ) under simulated solar illumination. In particular, a plateau photocurrent density of 0.21 mA cm –2 was achieved at a low potential of 0.4 V RHE , which was 1.6-fold and more than 50-fold higher than a two-dimensional macroporous (2DM) CaTaO 2 N/GaN/Al 2 O 3 photoanode and a conventional particle-based CaTaO 2 N/GaN/Al 2 O 3 photoanode, respectively. The bicontinuous, interconnected pore structure within this 3DM film can improve charge carrier separation and collection by reducing the average diffusion distance for minority carriers toward the electrolyte. Optical measurements and simulations verified the enhanced sunlight harvesting in the 3DM photoanode, which was ascribed to the concentrated distribution of the electric field and multiple scattering. Furthermore, this study provides guidance for future synthesis of highly efficient semitransparent 3DM quaternary oxynitride-based photoanodes for a tandem PEC device.

Layers↗
DOE OSTI2022

Metal Oxynitrides for the Electrocatalytic Reduction of Nitrogen to Ammonia

The successful deployment of technologies for the electrocatalytic nitrogen reduction reaction (e-NRR) to synthesize ammonia would enable distributed ammonia production with lower greenhouse gas emissions compared to the Haber–Bosch process. However, electrocatalysts that can readily activate N 2 , promote selective ammonia formation over the competing hydrogen evolution reaction, and maintain stability under reaction conditions are needed to enable this technology. Herein, we give our perspective on metal oxynitrides (A x B y O w N z ) as an emerging and underexplored materials class for e-NRR. Furthermore, we contrast the activity, selectivity, and stability of metal oxynitrides with those of their metal nitride and metal oxide counterparts. We discuss the different possible e-NRR reaction mechanisms on metal oxynitrides, emphasize challenges related to using metal oxynitrides for e-NRR, and provide an outlook for future research. Ultimately, the huge design space of metal oxynitrides is ripe for exploration to find catalyst formulations that overcome some of the limitations of traditional metal oxides and metal nitrides for e-NRR.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1991

Oxynitride glass fibers

Research at the Army Materials Technology Laboratory (AMTL) and elsewhere has shown that many glass properties including elastic modulus, hardness, and corrosion resistance are improved markedly by the substitution of nitrogen for oxygen in the glass structure. Oxynitride glasses, therefore, offer exciting opportunities for making high modulus, high strength fibers. Processes for making oxynitride glasses and fibers of glass compositions similar to commercial oxide glasses, but with considerable enhanced properties, are discussed. We have made glasses with elastic moduli as high as 140 GPa and fibers with moduli of 120 GPa and tensile strengths up to 2900 MPa. AMTL holds a U.S. patent on oxynitride glass fibers, and this presentation discusses a unique process for drawing small diameter oxynitride glass fibers at high drawing rates. Fibers are drawn through a nozzle from molten glass in a molybdenum crucible at 1550 C. The crucible is situated in a furnace chamber in flowing nitrogen, and the fiber is wound in air outside of the chamber, making the process straightforward and commercially feasible. Strengths were considerably improved by improving glass quality to minimize internal defects. Though the fiber strengths were comparable with oxide fibers, work is currently in progress to further improve the elastic modulus and strength of fibers. The high elastic modulus of oxynitride glasses indicate their potential for making fibers with tensile strengths surpassing any oxide glass fibers, and we hope to realize that potential in the near future.

Patel, Parimal J.↗
DOE OSTI2024

Triplet Exciton Sensitization of Silicon Mediated by Defect States in Hafnium Oxynitride

Singlet exciton fission has the potential to increase the efficiency of crystalline silicon solar cells beyond the conventional single junction limit. Perhaps the largest obstacle to achieving this enhancement is uncertainty about energy coupling mechanisms at the interfaces between silicon and exciton fission materials such as tetracene. Here, the previously reported silicon‐hafnium oxynitride‐tetracene structure is studied and a combination of magnetic‐field‐dependent silicon photoluminescence measurements and density functional theory calculations is used to probe the influence of the interlayer composition on the triplet transfer process across the hafnium oxynitride interlayer. It is found that hafnium oxide interlayers do not show triplet exciton sensitization of silicon, and that nitrogen content in hafnium oxynitride layers is correlated with enhanced sensitization. Calculation results reveal that defects in hafnium oxynitride interlayers with higher nitrogen content introduce states close to the band‐edge of silicon, which can mediate the triplet exciton transfer process. Some defects introduce additional deleterious mid‐gap states, which may explain observed silicon photoluminescence quenching. These results show that band‐edge states can mediate the triplet exciton transfer process, potentially through a sequential charge transfer mechanism.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Synthesis and symmetry of perovskite oxynitride CaW(O,N) 3

Perovskite oxynitrides, in addition to being promising electrocatalysts and photoabsorbers, present an interesting case study in crystal symmetry. Full or partial ordering of the O and N anions affects global symmetry and influences material performance and functionality; however, anion ordering is challenging to detect experimentally. In this work, we synthesize a novel perovskite oxynitride CaW(O,N) 3 and characterize its crystal structure using both X-ray and neutron diffraction. Through co-refinement of the diffraction patterns with a range of literature and theory-derived model structures, we demonstrate that CaW(O,N) 3 adopts an orthorhombic Pnma average structure and exhibits octahedral distortion with evidence for preferred anion site occupancy. However, through comparison with a large, low-symmetry unit cell, we identify the presence of disorder that is not fully accounted for by the high-symmetry model. We compare CaW(O,N) 3 with SrW(O,N) 3 to demonstrate the broader presence of such disorder and identify contrasting features in the electronic structures. This work signifies an updated perspective on the inherent crystal symmetry present in perovskite oxynitrides.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Perovskite oxynitrides as tunable materials for electrocatalytic nitrogen reduction to ammonia

The electrocatalytic nitrogen reduction reaction (ENRR) to ammonia is a potentially sustainable alternative to the Haber-Bosch (HB) process, but low Faradaic efficiencies and rates hinder its implementation. Perovskite oxynitrides are a tunable class of materials with unique chemistry for ENRR. As a result, elucidating structure–property–mechanism relations for perovskite oxynitrides will aid ENRR catalyst design.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Strain-induced creation and switching of anion vacancy layers in perovskite oxynitrides

Perovskite oxides can host various anion-vacancy orders, which greatly change their properties, but the order pattern is still difficult to manipulate. Separately, lattice strain between thin film oxides and a substrate induces improved functions and novel states of matter, while little attention has been paid to changes in chemical composition. Here we combine these two aspects to achieve strain-induced creation and switching of anion-vacancy patterns in perovskite films. Epitaxial SrVO 3 films are topochemically converted to anion-deficient oxynitrides by ammonia treatment, where the direction or periodicity of defect planes is altered depending on the substrate employed, unlike the known change in crystal orientation. First-principles calculations verified its biaxial strain effect. Like oxide heterostructures, the oxynitride has a superlattice of insulating and metallic blocks. Given the abundance of perovskite families, this study provides new opportunities to design superlattices by chemically modifying simple perovskite oxides with tunable anion-vacancy patterns through epitaxial lattice strain.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1995

Temperature dependence of the biaxial modulus, intrinsic stress and composition of plasma deposited silicon oxynitride films

Silicon oxynitride films were deposited by plasma-enhanced chemical-vapor deposition. The elemental composition was varied between silicon nitride and silicon dioxide: SiO(0.3)N(1.0), SiO(0.7)N(1.6), SiO(0.7)N(1.1), and SiO(1.7)N(0.%). These films were annealed in air, at temperatures of 40-240 C above the deposition temperature (260 C), to determine the stability and behavior or each composition. the biaxial modulus, biaxial intrinsic stress, and elemental composition were measured at discrete intervals within the annealing cycle. Films deposited from primarily ammonia possessed considerable hydrogen (up to 38 at.%) and lost nitrogen and hydrogen at anneal temperatures (260-300 C) only marginally higher than the deposition temperature. As the initial oxygen content increased a different mechanism controlled the behavior or the film: The temperature threshold for change rose to approximately equal to 350 C and the loss of nitrogen was compensated by an equivalent rise in the oxygen content. The transformation from silicon oxynitride to silica was completed after 50 h at 400 C. The initial biaxial modulus of all compositions was 21-3- GPa and the intrinsic stress was -30 to 85 MPa. Increasing the oxygen content raised the temperature threshold where cracking first occurred; the two film compositions with the highest initial oxygen content did not crack, even at the highest temperature (450 C) investigated. At 450 C the biaxial modulus increased to approximately equal to 100 GPa and the intrinsic stress was approximately equal to 200 MPa. These increases could be correlated with the observed change in the film's composition. When nitrogen was replaced by oxygen, the induced stress remained lower than the biaxial strength of the material, but, when nitrogen and hydrogen were lost, stress-relieving microcracking occurred.

Harding, David R.↗
DOE OSTI2021

A Review on Lithium Phosphorus Oxynitride

Lithium phosphorus oxynitride (LiPON) has paved the way for thin film solid-state battery technology development and has shown application in a large range of fields since its first reported synthesis in 1993. The term LiPON describes the family of materials with the general formula of LixPOyNz offering a great range of stoichiometries with varying properties. Understanding how the properties of LiPON are affected by different preparation methods is important for tuning this material to fit the required application. It is also useful to understand the LiPON relation between the amorphous structure and ionic conductivity, as well as the electrochemically degradation in contact with electrode materials. This review summarizes various methods of synthesizing LiPON and evaluates them on the basis of multiple properties of the resulting material. Structure–property relationships are identified to categorize the various LiPON stoichiometries that have been synthesized. Possible lithium ion conduction pathways and electrochemical degradation mechanism in LiPON are discussed. Representative applications of LiPON films are also introduced. At the end of this review, insights for future research into LiPON materials are provided.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Effect of Substrate Temperature on the Electrochemical and Supercapacitance Properties of Pulsed Laser-Deposited Titanium Oxynitride Thin Films

Electrocatalytically active titanium oxynitride (TiNO) thin films were fabricated on commercially available titanium metal plates using a pulsed laser deposition method for energy storage applications. The elemental composition and nature of bonding were analyzed using X-ray photoelectron spectroscopy (XPS) to reveal the reacting species and active sites responsible for the enhanced electrochemical performance of the TiNO electrodes. Symmetric supercapacitor devices were fabricated using two TiNO working electrodes separated by an ion-transporting layer to analyze their real-time performance. The galvanostatic charge–discharge studies on the symmetric cell have indicated that TiNO films deposited on the polycrystalline titanium plates at lower temperatures are superior to TiNO films deposited at higher temperatures in terms of storage characteristics. For example, TiNO films deposited at 300 °C exhibited the highest specific capacity of 69 mF/cm 2 at 0.125 mA/cm 2 with an energy density of 7.5 Wh/cm 2 . The performance of this supercapacitor (300 °C TiNO) device is also found to be ~22% better compared to that of a 500 °C TiNO supercapacitor with a capacitance retention ability of 90% after 1000 cycles. Furthermore, the difference in the electrochemical storage and capacitance properties is attributed to the reduced leaching away of oxygen from the TiNO films by the Ti plate at lower deposition temperatures, leading to higher oxygen content in the TiNO films and, consequently, a high redox activity at the electrode/electrolyte interface.

30 DIRECT ENERGY CONVERSION↗
NASA NTRS2017

Crack Growth Testing of an Aluminum Oxynitride (AlON) for International Space Station Kick Panes

The mechanical properties of an aluminum oxynitride supplied as ground beams and disks were measured using ASTM International (formerly American Society for Testing and Materials) standard test methods. The slow crack growth tests were complicated by a "short" finish that increased strength scatter. Refining of the finish by more material removal in the second stage of grinding or the use of uniaxial grinding as specified in ASTM C1499 might have avoided the issue. The structural design parameters are an elastic modulus of E = 319 GPa, Poisson's ratio of v = 0.26, a fracture toughness of KIvb(A) = 2.18 MPa/m, slow crack growth (SCG) parameter n = 36, and SCG parameter A = 1.96 x 10-11 m/s.(MPa/m)n. For a ground finish, the Weibull parameters are a mean modulus of m = 14.0 and characteristic strength of sigma theta = 250.2 MPa. The 2015 vintage material exhibits similar mechanical properties to a 2010 vintage billet. Indentation flaws were not sensitive to the inherent crack growth mechanisms of this material and produced misleading results.

strength↗
DOE OSTI2020

Local Structure of Glassy Lithium Phosphorus Oxynitride Thin Films: A Combined Experimental and Ab Initio Approach

Abstract Lithium phosphorus oxynitride (LiPON) is an amorphous solid‐state lithium ion conductor displaying exemplary cyclability against lithium metal anodes. There is no definitive explanation for this stability due to the limited understanding of the structure of LiPON. Herein, we provide a structural model of RF‐sputtered LiPON. Information about the short‐range structure results from 1D and 2D solid‐state NMR experiments. These results are compared with first principles chemical shielding calculations of Li‐P‐O/N crystals and ab initio molecular dynamics‐generated amorphous LiPON models to unequivocally identify the glassy structure as primarily isolated phosphate monomers with N incorporated in both apical and as bridging sites in phosphate dimers. Structural results suggest LiPON′s stability is a result of its glassy character. Free‐standing LiPON films are produced that exhibit a high degree of flexibility, highlighting the unique mechanical properties of glassy materials.

Marple, Maxwell A. T.↗
DOE OSTI2020

Local Structure of Glassy Lithium Phosphorus Oxynitride Thin Films: A Combined Experimental and Ab Initio Approach

Lithium phosphorus oxynitride (LiPON) is an amorphous solid–state lithium ion conductor displaying exemplary cyclability against lithium metal anodes. There is no definitive explanation for this stability due to the limited understanding of the structure of LiPON. Herein, we provide a structural model of RF–sputtered LiPON. Information about the short–range structure results from 1D and 2D solid–state NMR experiments. These results are compared with first principles chemical shielding calculations of Li–P–O/N crystals and ab initio molecular dynamics–generated amorphous LiPON models to unequivocally identify the glassy structure as primarily isolated phosphate monomers with N incorporated in both apical and as bridging sites in phosphate dimers. Structural results suggest LiPON's stability is a result of its glassy character. In conclusion, free–standing LiPON films are produced that exhibit a high degree of flexibility, highlighting the unique mechanical properties of glassy materials.

36 MATERIALS SCIENCE↗
DOE OSTI2026

In-Situ Visualization of a Growing Brittle Crack in Aluminum Oxynitride Using Synchrotron X-Rays and the Double-Cleavage Drilled Compression Geometry

Brittle fracture is difficult to study in situ due to the speed of a growing crack and the often-catastrophic nature of failure in brittle materials. As a result, the influence of microstructural considerations, such as orientation, grain boundary locations, and strain field, on the crack path remains poorly understood. Presented in this study is a method addressing this knowledge gap, which utilizes the double-cleavage drilled compression geometry to achieve quasi-stable fracture in aluminum oxynitride (AlON). Synchrotron X-ray micro-computed tomography is used to characterize the crack shape and length, while high-energy diffraction microscopy provides information on the strains, orientations, and shapes of grains in the microstructure surrounding the crack tip. During testing, the crack grew in discrete and irregular jumps while the fracture toughness falls within reported ranges. The crack in AlON is found to have no greater tendency to crack intergranularly as compared to transgranularly, and grains which are cracked transgranularly do not display a trend in orientation or stress when compared to those around which the crack followed a grain boundary. The high resolution of the crack path and microstructural data provides a path forward for modeling and understanding 3D brittle fracture.

Gorske, Sara F.↗
DOE OSTI2021

Influence of Cation Size on the Local Atomic Structure and Electronic Properties of Ta Perovskite Oxynitrides

Partial anion substitution in transition metal oxides provides rich opportunities to control and tune physical and chemical properties, for example, combining the merits of oxides and nitrides. In addition, the possibility of resulting anion sublattice order provides a means to target polar and chiral structures based on a wide array of accessible structural archetypes by design. Here, in this work, we investigate the local structures of a family of perovskite tantalum oxynitrides—ATaO 2 N (A = Ba, Sr, and Ca)—using a combination of experimental and theoretical approaches including neutron total scattering, density functional theory (DFT), and ab initio molecular dynamics (AIMD) simulations. We present the first experimental study of chemical short-range order (CSRO) in CaTaO 2 N, confirming local cis N ordering of the anion sub-lattice. Our systematic exploration of a local structure across the A cation size series (from the larger Ba to the smaller Ca) reveals a perovskite motif increasingly distorted with respect to long-range average structures. DFT and AIMD simulations support the observed trends. Overall, structures with cis ordering of the nitrogen anions in each TaO 4 N 2 octahedron are favored over those with trans ordering. With diminishing A cation size, local cis ordering and Ta off-centering play decreasing roles in overall lattice stability, overshadowed by the stabilizing effects of octahedral tilting. The influence of these factors on local dipole formation and frustrated dipole ordering are discussed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Elucidating Interfacial Stability between Lithium Metal Anode and Li Phosphorus Oxynitride via In Situ Electron Microscopy

Li phosphorus oxynitride (LiPON) is one of a very few solid electrolytes that have demonstrated high stability against Li metal and extended cyclability with high Coulombic efficiency for all solid-state batteries (ASSBs). However, theoretical calculations show that LiPON reacts with Li metal. Here, we utilize in situ electron microscopy to observe the dynamic evolutions at the LiPON–Li interface upon contacting and under biasing. We reveal that a thin interface layer (~60 nm) develops at the LiPON–Li interface upon contact. This layer is composed of conductive binary compounds that show a unique spatial distribution that warrants an electrochemical stability of the interface, serving as an effective passivation layer. Our results explicate the excellent cyclability of LiPON and reconcile the existing debates regarding the stability of the LiPON–Li interface, demonstrating that, though glassy solid electrolytes may not have a perfect initial electrochemical window with Li metal, they may excel in future applications for ASSBs.

25 ENERGY STORAGE↗