Search NASA⌕ Search

SEARCH · Search NASA

Results for “sliding joint”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

A Solution to Asymmetric Marangoni GTA Weld Behavior in a Dissimilar Chemistry Stainless Steel Joint [Slides]

Asymmetric and irregular weld morphology is an issue with the 9516 shipping container GTA weld. Observation of the weld puddle and cross sections showed the weld was biased toward the body side of the joint. This issue is attributed to a difference in the sulfur content and Marangoni fluid flow characteristics of the lid (150 ppm) and body (10 ppm) components of the weld joint. An additional contributing factor in this issue is the large difference in mass between the ½” thick lid and 1/8” thick body. A solution was developed comprised of a preliminary partial penetration weave pass across the joint intended to homogenize the sulfur content prior to the full penetration pass.

42 ENGINEERING↗

Seismic Modeling Workshop - Joint inversion [Slides]

Why joint inversion? It enables spanning spatial and data scales! Multiple benefits: Different data sets have different spatial coverage and resolution. “Standard” geophysical models are developed only to fit one type of data. Different data types have different strengths. Multiple challenges: Deal with different data bandwidths. Design responsive misfit norms; relative weighting of data sets. Make assumptions to model the different data; relationships between independent data sets.

58 GEOSCIENCES↗

Optimization of COMPASS-U Support Structure

The global support structure for Compass Upgrade (COMPASS-U) employs many bolted and pinned components to improve the manufacturability of the whole structures. This is a departure from other designs used for highly loaded tokamaks, like Alcator C-Mod which used large forgings. Modeling of the numerous connections and interfaces was a challenge. This article will describe how to optimize the C-frame support structure with the goal to eliminate differential displacements at those interfaces and, importantly, minimize toroidal mutual displacement at the sliding joint of the toroidal field (TF) coils. The global support structure consists of 16 C-frames, and it can be simplified as a 1/8th cyclic symmetry model due to the eight vertical rods mounting that connect bottom CS and PF1-3 assemblies to the C-frames. Structure variants with different connection webs between two neighboring C-frames have been analyzed. The preloading of bolts can be split into several preload substeps to simulate the real assembly process of the COMPASS-U support structure. Additionally, the TF crown and the wedge plate can be further improved to become a solid part to better hold the TF coils.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Structural development of laminar flow control aircraft chordwise wing joint designs

For laminar flow to be achieved, any protuberances on the surface must be small enough to avoid transition to turbulent flow. However, the surface must have joints between the structural components to allow assembly or replacement of damaged parts, although large continuous surfaces can be utilized to minimize the number the number of joints. Aircraft structural joints usually have many countersunk bolts or rivets on the outer surface. To maintain no mismatch on outer surfaces, it is desirable to attach the components from the inner surface. It is also desirable for the panels to be interchangeable, without the need for shims at the joint, to avoid surface discontinuities that could cause turbulence. Fabricating components while pressing their outer surfaces against an accurate mold helps to ensure surface smoothness and continuity at joints. These items were considered in evaluating the advantages and disadvantages of the joint design concepts. After evaluating six design concepts, two of the leading candidates were fabricated and tested using many small test panels. One joint concept was also built and tested using large panels. The small and large test panel deflections for the leading candidate designs at load factors up to +1.5 g's were well within the step and waviness requirements for avoiding transition.The small panels were designed and tested for compression and tension at -65 F, at ambient conditions, and at 160 F. The small panel results for the three-rib and the sliding-joint concepts indicated that they were both acceptable. The three-rib concept, with tapered splice plates, was considered to be the most practical. A modified three-rib joint that combined the best attributes of previous candidates was designed, developed, and tested. This improved joint met all of the structural strength, surface smoothness, and waviness criteria for laminar flow control (LFC). The design eliminated all disadvantages of the initial three-rib concept except for unavoidable eccentricity, which was reduced and reacted satisfactorily by the rib supports. It should also result in a relatively simple low-cost installation, and makes it easy to replace any panels damaged in the field.

Fischler, J. E.↗

Mode Conversion Losses in Expansion Units for ITER ECH Transmission Lines

The ITER electron cyclotron heating transmission lines will consist of 63.5 mm diameter corrugated waveguides, each carrying 1 MW of 170 GHz microwaves. These transmission lines must include expansion units to accommodate expansion and contraction along the path from the gyrotron microwave sources to the tokamak. A numerical mode matching code has been developed to calculate power losses due to mode conversion of the operating mode, HE11, to higher order modes as a result of the radial discontinuities in a sliding joint. Two expansion unit designs were evaluated, a simple gap expansion unit and a more complex tapered expansion unit. The gap expansion unit demonstrated loss that oscillated rapidly with expansion length, due to trapped modes within the unit. The tapered expansion unit has been shown to effectively suppress these trapped modes at the expense of increased fabrication complexity. In a gap expansion unit, for a waveguide step size of 2.5 mm, loss can be kept below 0.1% to a maximum expansion length of 17 mm. Expansion units without corrugation on interior walls were also evaluated. Expansion units that lack corrugations are found to increase mode trapping within the units, though not beyond useful application. The mode matching code developed in this paper was also used to estimate mode conversion loss in vacuum pumpouts for the ECH lines; the estimated loss was found to be negligibly small.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

External tank project new technology plan

A production plan for the space shuttle external tank configuration is presented. The subjects discussed are: (1) the thermal protection system, (2) thermal coating application techniques, (3) manufacturing and tooling, (4) propulsion system configurations and components, (5) low temperature rotating and sliding joint seals, (6) lightning protection, and (7) nondestructive testing technology.

Source record↗

Development progress, external tank for the Space Shuttle Main Propulsion System

Attention is given to the design parameters of the LH2/LO2 system in a description of the development of the external tank for the Space Shuttle Main Propulsion System (MPS). Design and functional changes for the MPS are reviewed, including: improvement of the vibroacoustic environment through the adaptation of a two-stage pilot to the existing basic valve design, a redesign of the GH2 vent line to accommodate increased deflections and loads, and the minimization of ice formation through slide joint insulation. The anti-geyser splash plate for the LO2 system is outlined in terms of fuel flow parameters under varying conditions of temperature and pressure, and test results for individual components are presented.

Norquist, L.↗

Fusion Nuclear Science Facility (FNSF) before Upgrade to Component Test Facility (CTF)

The compact (R0~1.2-1.3m) Fusion Nuclear Science Facility (FNSF) is aimed at providing a fully integrated, continuously driven fusion nuclear environment of copious fusion neutrons. This facility would be used to test, discover, understand, and innovate scientific and technical solutions for the challenges facing DEMO, by addressing the multi-scale synergistic interactions involving fusion plasma material interactions, tritium fuel cycle, power extraction, and the nuclear effects on materials. Such a facility properly designed would provide, initially at the JET-level plasma pressure (~30%T2) and conditions (e.g., Hot-Ion H-Mode), an outboard fusion neutron flux of 0.25 MW/m2 while requiring a fusion power of 19 MW. If and when this research operation is successful, its performance can be extended to 1 MW/m2 and 76 MW by reaching for twice the JET plasma pressure and Q. High-safety factor q and moderate- plasmas would minimize plasma-induced disruptions, helping to deliver reliably a neutron fluence of 1 MW-yr/m2 and a duty factor of 10% presently anticipated for the FNS research. Success of this research will depend on achieving time-efficient installation and replacement of all components using extensive remote handling (RH). This in turn requires modular designs for all internal components, including the single-turn toroidal field coil center-post with RH-compatible bi-directional sliding joints. Such device goals would further dictate placement of support structures and vacuum seal welds behind the internal and shielding components. If these further goals could be achieved, the FNSF would provide a ready upgrade path to the Component Test Facility (CTF), which would aim to test, at higher neutron fluence and duty cycle, the demanding fusion nuclear engineering and technologies for DEMO. This FNSF-CTF strategy would be complementary to the ITER and the Broader Approach programs, and thereby help mitigate the risks of an aggressive world fusion DEMO R&D Program. The key physics and technology research needed in the next decade to manage the potential risks of this FNSF are identified.

Peng, Yueng Kay Martin↗

Comparison of Joint Modeling Approaches Including Eulerian Sliding Interfaces

Accurate representation of discontinuities such as joints and faults is a key ingredient for high fidelity modeling of shock propagation in geologic media. The following study was done to improve treatment of discontinuities (joints) in the Eulerian hydrocode GEODYN (Lomov and Liu 2005). Lagrangian methods with conforming meshes and explicit inclusion of joints in the geologic model are well suited for such an analysis. Unfortunately, current meshing tools are unable to automatically generate adequate hexahedral meshes for large numbers of irregular polyhedra. Another concern is that joint stiffness in such explicit computations requires significantly reduced time steps, with negative implications for both the efficiency and quality of the numerical solution. An alternative approach is to use non-conforming meshes and embed joint information into regular computational elements. However, once slip displacement on the joints become comparable to the zone size, Lagrangian (even non-conforming) meshes could suffer from tangling and decreased time step problems. The use of non-conforming meshes in an Eulerian solver may alleviate these difficulties and provide a viable numerical approach for modeling the effects of faults on the dynamic response of geologic materials. We studied shock propagation in jointed/faulted media using a Lagrangian and two Eulerian approaches. To investigate the accuracy of this joint treatment the GEODYN calculations have been compared with results from the Lagrangian code GEODYN-L which uses an explicit treatment of joints via common plane contact. We explore two approaches to joint treatment in the code, one for joints with finite thickness and the other for tight joints. In all cases the sliding interfaces are tracked explicitly without homogenization or blending the joint and block response into an average response. In general, rock joints will introduce an increase in normal compliance in addition to a reduction in shear strength. In the present work we consider the limiting case of stiff discontinuities that only affect the shear strength of the material.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Validating Mixtures of 233 U, 235 U, and 239 Pu for the Sum-of-Fractions Method [Slides]

A joint effort by PNNL and ORNL examined mixtures of 233 U, 235 U, and 239 Pu to determine subcritical mass limits based on similarities to critical benchmark experiments through the Sum-of-Fractions method. Results of the validation efforts by ORNL were used to determine areas of applicability based on EALF and moderator/reflector type. TSUNAMI-1D, TSUNAMI-IP, and VADER sequences used for generating sensitivities, similarity assessments, and statistical testing. Validation efforts provided here using the Sum-of-Fractions method results in k eff values below established calculational margins and provides additional flexibility to limits provided in ANSI/ANS-8.15.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Joint DoD/DOE Munitions Program [Slides]

The JMP was established by an MOU between DOE and DoD in 1985. The JMP is one of three related programs administered by Jose Gonzalez in the Land Warfare and Munitions Office, AT&L. The other two programs are the Joint Fuze and Joint Insensitive Munitions Technology Programs. Oversight is provided by a Technical Advisory Committee (TAC) that is comprised of DoD Laboratory Directors, PMs, PEOs, and senior staff. Each DOE/NNSA weapons laboratory is responsible for identifying the appropriate local matching funds according to their individual needs and mission space.

36 MATERIALS SCIENCE↗

Stochastic Modeling of the Joint Neutron Number-Cumulative Fission Fragment Kinetic Energy Deposition Distribution and its Statistical Moments [Slides]

We investigate the joint distribution of the neutron number and cumulative fission-fragment kinetic energy (FKE) deposition, with a specific focus on low-order statistical moments: the mean, variance, and correlation. Starting from a point-kinetic framework, we derive a forward Master equation (FME) for the joint distribution and develop the corresponding moment equations.

42 ENGINEERING↗

A Comparative Study of Joint Modeling Methods and Analysis of Fasteners [Slides]

Motivation: Crucial aspect of mechanical design is joining methodology of parts. Ability to analyze joint and fasteners in system for structural integrity is fundamental. Different modeling representations of fasteners include spring, beam, and solid elements. Various methods compared for linear system to decide method appropriate for design study. New method for modeling fastener joint is explored from full system perspective. Analysis results match well with published experimental data for new method.

42 ENGINEERING↗

Near-field non-radial motion generation from underground chemical explosions in jointed granite

Here, this paper describes analysis of non-radial ground motion generated by chemical explosions in a jointed rock formation during the Source Physics Experiment (SPE). Such motion makes it difficult to discriminate between various subsurface events such as explosions, implosions (i.e. mine collapse) and earthquakes. We apply 3-D numerical simulations to understand experimental data collected during the SPEs. The joints are modelled explicitly as compliant thin inclusions embedded into the rock mass. Mechanical properties of the rock and the joints as well as the joint spacing and orientation are inferred from experimental test data, and geophysical and geological characterization of the SPE site which is dominantly Climax Stock granitic outcrop. The role of various factors characterizing the joints such as joint spacing, frictional properties, orientation and persistence in generation of non-radial motion is addressed. The joints in granite at the SPE site are oriented in nearly orthogonal directions with two vertical sets dipping at 70–80 degrees with the same strike angle, one vertical set almost orthogonal to the first two and one shallow angle joint set dipping 15 degrees. In this study we establish the relationship between the joint orientation and azimuthal variations in the polarity of the observed shear motion. The majority of the shear motion is generated due to the effects of non-elastic sliding on the joints near the source, where the wave can create significant shear stress to overcome the cohesive forces at the joints. Near the surface the joints are less confined and are subject to sliding when the pressure waves are reflected. In the far field, where the cohesive forces on the joints cannot be overcome, additional shear motion can be generated due to elastic anisotropy of the rock mass given by preferred spatial orientations of compliant joints.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗