Results for “surface defects”

NASA NTRS1984

The scattering of ultrasonic third sound from substrate surface defects

The interaction of third sound with isolated surface defects is examined. Phase-inverted reflections are observed to occur at surface defects even when the wavelength of the third sound is much greater than the dimensions of the defect. The origin of the scattering mechanism is believed to be due to the change in the helium film thickness in the vicinity of the topological variations introduced by the presence of the surface defects. Data are obtained for ultrasonic frequencies in the 20-200 kHz range.

Generazio, E. R.↗

DOE OSTI2026

Correlation of coercivity, microstructure, and surface defects in HDDR-processed Nd-Fe-B powders for bonded magnet applications

Hydrogenation-Disproportionation-Desorption-Recombination (HDDR) is an effective method for producing high coercivity, anisotropic powder from either fresh Nd-Fe-B alloy or recycled Nd-Fe-B magnets for use in bonded magnets. We investigated the impact of surface defects on the coercivity of HDDR-processed Nd-Fe-B using scanning electron microscopy (SEM), magnetic measurements, and micromagnetic simulations. We observed that coercivity decreases as particle size reduces, with SEM revealing surface defects and the detachment of Nd 2 Fe 14 B grains and Nd-rich phases from the particle surface. Micromagnetic simulations indicate that demagnetization initiates at the particle surface, where these defects are most concentrated, leading to reduced coercivity. The reduction in squareness of demagnetization curve, knee point field and coercivity for smaller HDDR particles is attributed to an increased specific surface area, which exhibits reduced nucleation field and weak domain wall pinning field during magnetization reversal. By addressing the role of surface defects in coercivity degradation, this study provides insights for improving both new powder production and recycling strategies, ultimately leading to enhanced performance of bonded magnets and contributing to more sustainable practices in the rare earth supply chain. One potential strategy to enhance the performance of HDDR Nd-Fe-B materials involves reducing the fraction of fine particles ($<$35 µm) and promoting the formation of grain boundary phases on particle surfaces.

Liu, Xubo B. [Ames Laboratory (AMES), Ames, IA (Un↗

NASA NTRS1994

System and process for detecting and monitoring surface defects

A system and process for detecting and monitoring defects in large surfaces such as the field joints of the container segments of a space shuttle booster motor. Beams of semi-collimated light from three non-parallel fiber optic light panels are directed at a region of the surface at non-normal angles of expected incidence. A video camera gathers some portion of the light that is reflected at an angle other than the angle of expected reflectance, and generates signals which are analyzed to discern defects in the surface. The analysis may be performed by visual inspection of an image on a video monitor, or by inspection of filtered or otherwise processed images. In one alternative embodiment, successive predetermined regions of the surface are aligned with the light source before illumination, thereby permitting efficient detection of defects in a large surface. Such alignment is performed by using a line scan gauge to sense the light which passes through an aperture in the surface. In another embodiment a digital map of the surface is created, thereby permitting the maintenance of records detailing changes in the location or size of defects as the container segment is refurbished and re-used. The defect detection apparatus may also be advantageously mounted on a fixture which engages the edge of a container segment.

Mueller, Mark K.↗

DOE OSTI2026

Effect of macroscopic surface defects on dynamic damage: An experimental and numerical study

This study examines the impact of macroscopic surface defects on the dynamic ductile damage behavior of polycrystalline metals using plate-impact experiments. Defects of various shapes (flat, round, and point) were manufactured on the free or impact surfaces of annealed copper specimens. The experiments were diagnosed with photon Doppler velocimetry measurements and soft recovery techniques. The experimental results revealed that defect shape and location significantly affect velocity–time profiles and void distribution. In order to understand the dynamics of shock propagation and corresponding ductile damage evolution within the target specimens, the impact experiments were modeled with a calibrated Tepla model, a dynamic ductile damage model for polycrystalline metals [Nguyen et al., Int. J. Solids Struct. 329, 113833 (2026)]. Overall, our resulting simulated velocity showed good agreement with measured velocity, and our simulated porosity distributions qualitatively matched experimental data. Based on our simulation results, defects on the free surface were found to distort rarefaction waves and therefore the corresponding spall planes. On the other hand, defects on the impact surface generated a delayed shock when the flyer plate and the defected target area were in contact, leading to distortion of the spall plane. The distortion of the spall plane resulted in a non-uniform distribution of voids within the defected specimens. Lastly, we examined the role of local work hardening due to the defect manufacturing process on the velocity and porosity distribution, using Tepla simulations with a simplified representation of local hardening. This investigation highlights the importance of defect geometry, location, and local hardening associated with defect generation in dynamic ductile damage processes.

36 MATERIALS SCIENCE↗

NASA NTRS1990

Surface defects and chemistry on the SnO2(110) surface

A variety of ultrahigh vacuum (UHV) surface science techniques have been used to characterize the structural, electronic and chemical properties of SnO2(110), a model catalytic surface. Two types of surface oxygen vacancies have been identified, each associated with different band gap (defect) electronic states. Adsorption experiments show that the interaction of simple gases with this surface occurs primarily through these oxygen vacancies and can show site-specificity to only one of the two types of vacancies.

Cox, David F.↗

NASA NTRS2011

Phase Retrieval System for Assessing Diamond Turning and Optical Surface Defects

An optical design is presented for a measurement system used to assess the impact of surface errors originating from diamond turning artifacts. Diamond turning artifacts are common by-products of optical surface shaping using the diamond turning process (a diamond-tipped cutting tool used in a lathe configuration). Assessing and evaluating the errors imparted by diamond turning (including other surface errors attributed to optical manufacturing techniques) can be problematic and generally requires the use of an optical interferometer. Commercial interferometers can be expensive when compared to the simple optical setup developed here, which is used in combination with an image-based sensing technique (phase retrieval). Phase retrieval is a general term used in optics to describe the estimation of optical imperfections or aberrations. This turnkey system uses only image-based data and has minimal hardware requirements. The system is straightforward to set up, easy to align, and can provide nanometer accuracy on the measurement of optical surface defects.

Dean, Bruce↗

NASA NTRS2013

Surface Inspection Tool for Optical Detection of Surface Defects

The Space Shuttle Orbiter windows were damaged both by micrometeor impacts and by handling, and required careful inspection before they could be reused. The launch commit criteria required that no defect be deeper than a critical depth. The shuttle program used a refocus microscope to perform a quick pass/fail determination, and then followed up with mold impressions to better quantify any defect. However, the refocus microscope is slow and tedious to use due to its limited field of view, only focusing on one small area of glass at a time. Additionally, the unit is bulky and unable to be used in areas with tight access, such as defects near the window frame or on the glass inside the Orbiter due to interference with the dashboard. The surface inspection tool is a low-profile handheld instrument that provides two digital video images on a computer for monitoring surface defects. The first image is a wide-angle view to assist the user in locating defects. The second provides an enlarged view of a defect centered in the window of the first image. The focus is adjustable for each of the images. However, the enlarged view was designed to have a focal plane with a short depth. This allows the user to get a feel for the depth of different parts of the defect under inspection as the focus control is varied. A light source is also provided to illuminate the defect, precluding the need for separate lighting tools. The software provides many controls to adjust image quality, along with the ability to zoom digitally the images and to capture and store them for later processing.

Nurge, Mark↗

NASA NTRS1971

Dye penetrant indications caused by superficial surface defects in 2014 aluminum alloy welds.

Demonstration that dye penetrant indications on the heat-affected zone of 2014-T6 aluminum GMA weldments are frequently caused by superficial surface conditions and are less than 0.007 in. deep. The following methods are suggested for minimization of these surface defects: stabilization of the arc, application of dc ?GTA' welding procedures, reduction of the caustic etch time, and use of fine grain materials.

Hocker, R. G.↗

NASA NTRS2002

Evaluation of New Repair Methods for Seal Surface Defects on Reusable Solid Rocket Motor (RSRM) Hardware

The focus of the evaluation was to develop a back-up method to cell plating for the improvement or repair of seal surface defects within D6-AC steel and 7075-T73 aluminum used in the RSRM program. Several techniques were investigated including thermal and non-thermal based techniques. Ideally the repair would maintain the inherent properties of the substrate without losing integrity at the repair site. The repaired sites were tested for adhesion, corrosion, hardness, microhardness, surface toughness, thermal stability, ability to withstand bending of the repair site, and the ability to endure a high-pressure water blast without compromising the repaired site. The repaired material could not change the inherent properties of the substrate throughout each of the test in order to remain a possible technique to repair the RSRM substrate materials. One repair method, Electro-Spark Alloying, passed all the testing and is considered a candidate for further evaluation.

Stanley, Stephanie D.↗

NASA NTRS2003

Evaluation of New Repair Methods for Seal Surface Defects on Reusable Solid Rocket Motor (RSRM) Hardware

The focus of the evaluation was to develop a back-up method to cell plating for the improvement or repair of seal surface defects within D6-AC steel and 7075-T73 aluminum used in the RSRM program. Several techniques were investigated including thermal and non-thermal based techniques. Ideally the repair would maintain the inherent properties of the substrate without losing integrity at the repair site. The repaired sites were tested for adhesion, corrosion, hardness, microhardness, surface toughness, thermal stability, ability to withstand bending of the repair site, and the ability to endure a high-pressure water blast without compromising the repaired site. The repaired material could not change the inherent properties of the substrate throughout each of the test in order to remain a possible technique to repair the RSRM substrate materials. One repair method, Electro-Spark Alloying, passed all the testing and is considered a candidate for further evaluation.

Stanley, Stephanie↗

NASA NTRS2001

Identification of Surface and Near Surface Defects and Damage Evaluation by Laser Speckle Techniques

As a part of the grant activity, a laboratory was established within the Department of Electrical Engineering for the study for measurements of surface defects and damage evaluation. This facility has been utilized for implementing several algorithms for accurate measurements of defects. Experiments were conducted using simulated images and multiple images were fused to achieve accurate measurements. During the nine months of the grants when the principal investigator was transferred in my name, experiments were conducted using simulated synthetic aperture radar (SAR) images. This proved useful when several algorithms were used on images of smooth objects with minor deformalities. Given the time constraint, the derived algorithms could not be applied to actual images of smooth objects with minor abnormalities.

Gowda, Chandrakanth H.↗

DOE OSTI2025

CO 2 Hydrogenation on Pd(111): The Role of Subsurface Hydrogen and Surface Defects

Palladium-based catalysts are often used in carbon dioxide (CO 2 ) hydrogenation reactions with different possible reaction pathways producing methanol, methane, formic acid, or carbon monoxide. We used ambient pressure X-ray photoelectron spectroscopy (AP-XPS) to understand the surface reaction mechanism of CO 2 hydrogenation on Pd(111). AP-XPS results show that the order in which the reactants are introduced yields different initial surface species. In a CO 2 and H 2 mixture, carbonaceous species (CH x , C*, PdC x ) are formed upon heating Pd(111) at 400 K and above. In addition, a Pd(111) sample pre-exposed to an elevated pressure of H 2 followed by evacuation to ultrahigh vacuum (UHV) can store enough hydrogen atoms in the subsurface and bulk to provide a hydrogen source for the CO 2 hydrogenation reaction to occur when exposed to CO 2 gas alone. In conclusion, the formation of carbonaceous species likely occurs through the decomposition of a transient CH x O intermediate facilitated by low-coordinated sites and surface defects.

36 MATERIALS SCIENCE↗

NASA NTRS1987

The effects of wall surface defects on boundary-layer transition in quiet and noisy supersonic flow

The design of supersonic vehicles with laminar flow control and vehicles such as the Space Shuttle requires information on allowable transition tolerances to fabrication defects such as discrete surface roughness and waviness. A relatively large data base on the effects of discrete roughness on transition exists for subsonic and supersonic speeds. The existing supersonic wind tunnel transition data are contaminated by wind tunnel noise emanating from the turbulent boundary layers on the nozzle walls. Roughness and waviness transition data obtained in a quiet Mach 3.5 supersonic wind tunnel are compared with those obtained in conventional noisy flows.

Morrisette, E. Leon↗

NASA NTRS1995

Optoelectronic Instruments For Analysis Of Surface Defects

Family of portable optoelectronic instruments developed to facilitate inspection of surface flaws like gouges, scratches, raised metal, and dents on large metal workpieces subject to surface-finish requirements. Instrument brought to workpiece and semiautomatically makes electronic record of three-dimensional shape of flaw. Entire inspection process takes only minutes. Prototype instrument includes structured-light microscope. Concept involves projection of known pattern of light onto surface inspected. Topography of surface determined from distortion of pattern as viewed through instrument.

Collins, J. David↗

NASA NTRS1979

Influence of alignment and surface defects on the performance of X-ray telescopes

The effects of misalignment and surface deformations on the image quality of a grazing incidence telescope with six nested subsystems are investigated. The axial rms-spot size serves as a measure for the image quality. The surface deformations are simulated by ellipsoidal and sinusoidal deviations from the ideal surface. Misalignments are tilts, decenters, and despaces of the individual elements. The effects of each type of defect are analyzed in a single two-element system. The full nested system is then analyzed in the presence of all possible defects on all 12 elements, whereby the magnitude of the defects is randomized within a given upper limit.

Korsch, D.↗

DOE OSTI2025

Influence of Surface Defects on WO 3 Photoelectrodes for Catalyzing Chloride Oxidation in Water

Tungsten oxide (WO 3 ) is an n-type semiconductor due to oxygen vacancies (□ O •• in Kroger-Vink notation) or surface protonation as H x WO 3 . It is one of the few acid-stable oxides under large positive bias, which makes WO 3 ideal for interrogating the mechanism of the chloride oxidation reaction (COR). The large, positive valence band edge of ∼3 eV provides the overpotential necessary to carry out the COR, but the reaction competes with the oxygen-evolution reaction in water. The □ O •• defect density can be controlled by the atmosphere under which the material is annealed, so WO 3 films were prepared by a spin-coating method from an ammonium metatungstate precursor annealed at 500 °C under air, flowing O 2 , and flowing argon. Annealing the films in a flowing O 2 atmosphere hinders the formation of □ O ••, and annealing in Ar leads to greater surface W 6+ , likely due to expelling intercalated H + . The saturated photocurrent density (j ph ) is highest in films with the greatest concentration of W 5+ and greatest concentration of oxide defects: (0.66 mA/cm 2 annealed in air, 0.58 mA/cm 2 annealed in Ar, and 0.49 mA/cm 2 annealed in O 2 , reported at 1.5 V vs Ag/AgCl, pH 3 (before the onset of a dark reaction). The defect concentrations are determined by X-ray photoelectron spectroscopy. In all cases the Faradaic efficiency for the COR is near unity. Finally, we demonstrate that W 5d states can be probed by ligand K-edge X-ray absorption near-edge spectroscopy via pre-edge (Cl 1s → W 5d) transitions, lower in energy than the ligand-centered (Cl 1s → 4p) transition. We use this analysis to show the presence of W─Cl covalent bonds on the WO 3 films post-COR, corroborated by DFT calculations. Furthermore, this result stands in contrast to the commonly assumed mechanistic proposal invoking outer-sphere electron transfer to a physisorbed chloride ion.

Cl K-edge↗

NASA NTRSDate not supplied

Discerning Cell Surface Defects with 3D Optical Profilometry

This investigation seeks to establish better criteria that can be used for qualitative visual screening of cylindrical battery cells through exploration of various defects across multiple cylindrical Lithium-Ion battery cells. This investigation focuses on INR18650s and INR21700s cells from Molicel, LG, and Samsung. The principal instrument used is a high-definition 3D optical profilometer with measurement accuracy less than 0.5 microns. Through this effort, a catalog was built discerning minor surface imperfections from significant flaws. The catalog generated covers a comparison of axial and radial scratches, less than 5 microns, greater than 5 microns and greater than 15 microns, as well as the difference between surface discoloration, early-stage pitting, and late stages of corrosion. An exploration is made into cell button defects and crimp shoulder defects. When ultra-high-power optical magnification and three-dimension topological tools are not immediately available, this catalog will help determine if an individual cell is usable, worth further investigation, or failing. The purpose of this catalog is to be a field guide used for quick reference of a potential issue, with the goal of increasing screening throughput while reducing the need for costly examination. Trade names and trademarks are used in this abstract for identification only. Their usage does not constitute an official endorsement, either expressed or implied, by the National Aeronautics and Space Administration.

battery↗

NASA NTRSDate not supplied

Discerning Cell Surface Defects with 3D Optical Profilometry

This investigation seeks to establish better criteria that can be used for qualitative visual screening of cylindrical battery cells through exploration of various defects across multiple cylindrical Lithium-Ion battery cells. This investigation focuses on INR18650s and INR21700s cells from Molicel, LG, and Samsung. The principal instrument used is a high-definition 3D optical profilometer with measurement accuracy less than 0.5 microns. Through this effort, a catalog was built discerning minor surface imperfections from significant flaws. The catalog generated covers a comparison of axial and radial scratches, less than 5 microns, greater than 5 microns and greater than 15 microns, as well as the difference between surface discoloration, early-stage pitting, and late stages of corrosion. An exploration is made into cell button defects and crimp shoulder defects. When ultra-high-power optical magnification and three-dimension topological tools are not immediately available, this catalog will help determine if an individual cell is usable, worth further investigation, or failing. The purpose of this catalog is to be a field guide used for quick reference of a potential issue, with the goal of increasing screening throughput while reducing the need for costly examination. Trade names and trademarks are used in this abstract for identification only. Their usage does not constitute an official endorsement, either expressed or implied, by the National Aeronautics and Space Administration.

battery↗