Engineering topics

Bortolotti, Pietro (ORCID:0000000285159488)

Publications and source records attributed to Bortolotti, Pietro (ORCID:0000000285159488).

18 records

DOE OSTI2025

An AI-Based 3D Bat Movement Tracking System at Wind Energy Facilities Using Multi-Thermal Video Cameras

The poster at the 15th Wind Wildlife Research Meeting discusses how to leverage the potential of real-time thermal-imaging methodologies in quantifying nocturnal bat activities at wind turbines, using 3D computer vision techniques within a deep learning framework. This innovation enables the automatic detection and classification of bats, birds, and insects in thermal-imaging videos captured at wind turbine sites, facilitating efficient and accurate data analysis for enhanced understanding and mitigation of bat-wind turbine interactions.

AI↗

DOE OSTI2024

Wind Turbine Design Optimization for Hydrogen Production

To help meet the need for inexpensive green fuels, we are working on wind turbine design optimization specifically for hydrogen production. We have thus far achieved a 1.53% decrease in LCOH as compared to a turbine optimized for LCOE using the same code, design variables, and models. We accomplished this by optimizing some components of the wind turbine tower, rotor, and drivetrain design with hydrogen production and costs in the design loop.

hydrogen↗

DOE OSTI2024

Comparison of Loads and Aeroacoustics Between Upwind and Downwind Wind Turbine Rotors

This presentation discusses the motivation, preparation, risk mitigation, execution, and results of a full-scale experiment where the rotor of a 1.5 megawatt wind turbine was operated in a downwind configuration. The experiment took place at the National Renewable Energy Laboratory Flatirons Campus in Colorado, USA, and collected conventional loads and power together with acoustic measurements from an array of four microphones. Results from load simulations complement the experiment. Fatigue loads and performance are compared between 410 minutes of downwind operation with 960 minutes of conventional upwind operations. Downwind operations cause an increase in damage equivalent loads in a few load channels. Damage equivalent load of blade root flapwise and edgewise moment and the damage equivalent load of tower base fore aft moment increase between 2% and 20% depending on the wind speed. The comparison in active power is less conclusive, but experimental results show more power in downwind than predicted by simulations. In terms of acoustics, the overall sound pressure levels are similar between upwind and downwind, but downwind worsens the metrics describing amplitude modulation.

aeroacoustics↗

DOE OSTI2024

One-to-one aeroservoelastic validation of operational loads and performance of a 2.8 MW wind turbine model in OpenFAST

Abstract. This article presents a validation study of the popular aeroservoelastic code suite OpenFAST leveraging weeks of measurements obtained during normal operation of a 2.8 MW land-based wind turbine. Measured wind conditions were used to generate one-to-one turbulent flow fields (i.e., comparing simulation to measurement in 10 min increments, or bins) through unconstrained and constrained assimilation methods using the kinematic turbulence generators TurbSim and PyConTurb. A total of 253 bins of 10 min of normal turbine operation were selected for analysis, and a statistical comparison in terms of performance and loads is presented. We show that successful validation of the model was not strongly dependent on the type of inflow assimilation method used for mean quantities of interest, which had median modeling errors per wind-speed interval generally within 5 %–10 % of the measurement. The type of inflow assimilation method did have a larger effect on the fatigue predictions for blade-root flapwise and tower-base fore–aft quantities, which surprisingly saw larger errors from the assumed higher-fidelity assimilation methods. Avenues for further work are discussed and include possible improvements to the aerodynamic, structural, and controller modeling that may offer insight on the origin of the up to ∼ 40 % median overprediction of fatigue for these quantities.

17 WIND ENERGY↗

DOE OSTI2024

Sound at Scale: Characterizing Impacts of Noise Ordinances on the Onshore Wind Energy Technical Potential for the United States

Recent surveys have documented the rapid rise of sound ordinances across state and county jurisdictions, which has become crucial for wind energy siting. However, the lack of information on ordinances and computational challenges in turbine sound modeling create uncertainties regarding how evolving policies may affect resource potential and clean energy objectives. Therefore, we develop an approach to evaluate wind turbine sound profiles at millions of locations across the U.S. and translate them into setback distances for every residential structure. Compared to a baseline reference scenario, we find a 7% reduction in the national wind energy capacity potential when accounting for counties with existing sound ordinances. Additionally, when expanding the surveyed sound ordinances nationwide, we observe a potential loss of 53% of the national wind capacity under the most stringent ordinances, with a disproportionate share of this lost capacity coming from high-quality and low-cost wind resource. This work reveals that neglecting sound ordinances results in a significant overestimation of wind resource potential and highlights the important trade-offs between increased wind energy deployment to meet target decarbonization goals and the social/environmental impacts of this deployment that must be considered.

aeroacoustics↗

DOE OSTI2024

The Future of Land-Based Wind Turbine Rotor Technology: The Perspective from NREL

The Big Adaptive Rotor (BAR) Project looks at potential innovative pathways for future land-based wind turbine technology. BAR is led by the National Renewable Energy Laboratory and is sponsored by the Wind Energy Technology Office of the US Department of Energy. This talk will describe innovations and challenges faced by the teams working on BAR. The innovations include numerical models predicting the stability and performance of highly flexible blades, downwind rotors to maximize wind farm power, and controlled bending of 100-meter-long blades during rail transport. The challenges of developing predictive numerical models and formulating successful value propositions supporting new technologies such as distributed aero control devices will also be discussed.

BAR↗

DOE OSTI2023

Capturing Time-Varying Wake Dynamics Using Hybridized Actuator Disks in Steady-State Simulations for Improved Optimization Efficiency

When optimizing turbine blade properties, using a time varying, unsteady simulation allows for high-fidelity representations of the wake dynamics. Unfortunately these types of optimizations are prohibitively expensive in terms of computation time and memory requirements. This presentation aims to show a method of transferring the wake dynamics of an unsteady simulation to a much more computationally tractable steady state simulation using hybrid actuator disks informed by unsteady, actuator line model dynamics.

actuator disk model↗

DOE OSTI2023

Design Space Exploration for Novel Reduced-Vortex Turbine Rotors Using Free Vortex Wake Methods

In this work, we explore the use of mid-fidelity free vortex wake (FVW) tools, namely NREL's cOnvecting LAgrangian Filaments (OLAF) tool, to design and analyze wind turbine rotor blades. The goal of the exercise is to determine whether designs exist that out-perform traditional blade designs, which are optimized using the Blade-Element Momentum (BEM) method. We find that using design of experiments to generate simple modifications of the blade tip, OLAF predicts higher performance in terms of power coefficient for redesigned blades that are non-optimal according to BEM. We then use optimization methods with OLAF in the loop to attempt to automatically find OLAF-optimal designs. We analyze the results of these optimizations, demonstrating that some roadblocks exist before OLAF and FVW tools can be used to automatically find FVW-optimal blade designs that might exceed the performance of BEM-optimal blade designs.

blade design↗

DOE OSTI2023

Wind Turbine Design Optimization for Hydrogen Production

To help meet the need for inexpensive green fuels, we are working on wind turbine design optimization specifically for hydrogen production. We have thus far achieved a 1.53% decrease in LCOH as compared to a turbine optimized for LCOE using the same code, design variables, and models . We accomplished this by optimizing some components of the wind turbine tower, rotor, and drivetrain design with hydrogen production and costs in the design loop.

design↗

DOE OSTI2023

How to Flip a GE1.5 Wind Turbine from Upwind to Downwind

An experiment is planned on a 1.5 MW wind turbine to make its rotor operate in a downwind configuration. The talk at the NAWEA WindTech 2023 conference will discuss how such a challenging experiment has been prepared and will show the ongoing steps in the field.

big adaptive rotor↗

DOE OSTI2023

Optimization and Comparison of Modern Offshore Wind Turbine Generators Using GeneratorSE 2.0

As the offshore wind industry keeps growing at a rapid pace, developers are bracing themselves for a huge demand in critical rare earth metals which will threaten an already vulnerable supply chain. The wind energy industry is addressing this problem by investing in modern generator technologies that employ magnets with reduced rare earth content and high-field magnets enabled by rare-earth-free superconductors. In this paper we introduce the National Renewable Energy Laboratory's newly advanced GeneratorSE 2.0, which is a design and optimization tool that was developed to investigate the feasibility of such modern generators. Two direct-drive generator topologies with different magnet materials and mounting arrangements are investigated: an outer-rotor, V-shaped interior permanent magnet generator, and an inner-rotor normally conducting armature, paired with a low-temperature superconducting field with race-track coils. These technologies were evaluated for a range of power ratings between 15 and 25 MW, which represent the next generation of offshore wind turbines for both fixed-bottom and floating applications. The analyses indicate a new trend favoring the low-temperature superconducting technology for the direct-drive system.

direct-drive generators↗

DOE OSTI2023

Wind Turbine Noise Code Benchmark: A Comparison and Verification Exercise: Preprint

In a number of institutions and companies, researchers and engineers are developing modeling numerical frameworks that are used to predict the aerodynamic noise emission from a wind turbine rotor. The simulation codes vary from empirically-tuned engineering models to high-fidelity computational ones. Their common feature is the fact that they all specifically model the main aerodynamic noise mechanisms occurring at the rotating blades, namely trailing edge noise and turbulent inflow noise. Nevertheless, it can be expected that these different modeling frameworks will produce different results for a same given rotor design, and identical operating conditions. Trailing edge noise is put at the forefront of the study as it is recognized as the main audible source of noise from wind turbines. The present benchmark aims at comparing the results from the different modeling approaches, and drawing some conclusions from these comparisons. This effort, denoted as Wind Turbine Noise Code benchmark, was initiated in 2019 as a joint-activity between the IEA Wind Task 39 (Quiet Wind Turbine Technology) and Task 29 (Detailed Aerodynamics of Wind Turbines, now Task 47). In addition to the investigation of the noise emissions themselves, the rotor aerodynamic characteristics are investigated as they have a significant impact on the noise generation mechanisms. A number of test cases are defined and the aerodynamic and aeroacoustic predictions from the various models are compared. There exist some discrepancies between the different methods, but it is difficult to conclude if one methodology is better than another in order to design a wind turbine with noise as a constraint.

aeroacoustics↗

DOE OSTI2023

A Comparison of Generator Technologies for Offshore Wind Turbines

Leading wind turbine manufacturers are racing to build larger and more powerful offshore machines. Drivetrain configurations often use a permanent-magnet synchronous generator (PMSG), in either a direct-drive configuration or coupled to a gearbox. With increasing demand for critical rare-earth magnets, new generator technologies are emerging to ensure a stable and secure supply chain. We evaluate three different topologies of radial flux synchronous generators employing high field magnets with reduced or no rare-earth content: a direct-drive interior PMSG (DD-IPMSG), a geared drivetrain combining a medium speed gearbox with a PMSG (MS-PMSG), and a direct-drive low-temperature superconducting generator (DD-LTSG). We develop a conceptual design module for each of these technologies within a larger framework for full turbine design. This provides the fairest comparison between technologies at nominal power ratings from 15-25MW, which represent the next generation of offshore wind turbines. The analyses show that if operational expenditures (OpEx) are constant across the technologies, MS-PMSG results in the lowest LCOE with reductions of up to 7% relative to DD-IPMSG. DD-LTSG also yields lower LCOE values by 2-3% for fixed-bottom turbines and 3-5% with a floating platform. However, results are sensitive to OpEx assumptions, with a mere 10% increase causing the conclusions to shift.

direct drive↗

DOE OSTI2023

Toward the Advanced Manufacturing of Land-Based Wind Turbine Blades

The National Renewable Energy Laboratory and General Electric (GE) are partners within the Additive and Modular-Enabled Rotor Blades and Integrated Composites Assembly (AMERICA) project. AMERICA aims to develop advanced manufacturing solutions to reduce labor and cycle time while increasing recyclability of wind turbine blades. The project is funded by the U.S. Department of Energy's Advanced Manufacturing Office. This paper describes the techno-economic and life cycle analysis of the novel manufacturing process applied to the 15-meter long tip of the blade of a representative 3.4 MW land-based wind turbine. We establish a comparison to a standard manufacturing process, highlighting challenges and opportunities. Several uncertainties affect the analysis, but we highlight an opportunity space. With the current set of assumptions, the tip adopting advanced manufacturing is predicted to lower labor by 21%, cycle time by 39%, and total blade tip costs by 15% while simultaneously increasing production quality and adopting recyclable thermoplastic resin. A life cycle analysis returns comparable metrics for climate change impact and embodied energy between the two processes.

3D printing↗

DOE OSTI2022

Toward the Advanced Manufacturing of Land-Based Wind Turbine Blades: Preprint

The National Renewable Energy Laboratory (NREL) and General Electric (GE) are partners within the Additive and Modular Enabled Rotor Blades and Integrated Composites Assembly (AMERICA) project. AMERICA aims to develop advanced manufacturing solutions to reduce labor and cycle time while increasing recyclability of wind turbine blades. The project is funded by the Advanced Manufacturing Office (AMO) of the U.S. Department of Energy (DOE). This paper describes the techno-economic analysis of the novel manufacturing process applied to the tip of the blade of a representative land-based wind turbine. A comparison to a standard manufacturing process is established, highlighting challenges and opportunities. Several uncertainties affect the analysis, but with the current set of assumptions, the tip adopting advanced manufacturing is predicted to lower labor by 21%, cycle time by 39%, and total blade tip costs by 15% while simultaneously increasing production quality and adopting recyclable thermoplastic resin.

3D printing↗

DOE OSTI2022

Effectively using multifidelity optimization for wind turbine design

Abstract. Wind turbines are complex multidisciplinary systems that are challenging to design because of the tightly coupled interactions between different subsystems. Computational modeling attempts to resolve these couplings so we can efficiently explore new wind turbine systems early in the design process. Low-fidelity models are computationally efficient but make assumptions and simplifications that limit the accuracy of design studies, whereas high-fidelity models capture more of the actual physics but with increased computational cost. This paper details the use of multifidelity methods for optimizing wind turbine designs by using information from both low- and high-fidelity models to find an optimal solution at reduced cost. Specifically, a trust-region approach is used with a novel corrective function built from a nonlinear surrogate model. We find that for a diverse set of design problems – with examples given in rotor blade geometry design, wind turbine controller design, and wind power plant layout optimization – the multifidelity method finds the optimal design using 38 %–58 % of the computational cost of the high-fidelity-only optimization. The success of the multifidelity method in disparate applications suggests that it could be more broadly applied to other wind energy or otherwise generic applications.

17 WIND ENERGY↗

DOE OSTI2022

Land-based wind turbines with flexible rail-transportable blades – Part 2: 3D finite element design optimization of the rotor blades

Abstract. Increasing growth in land-based wind turbine blades to enable higher machine capacities and capacity factors is creating challenges in design, manufacturing, logistics, and operation. Enabling further blade growth will require technology innovation. An emerging solution to overcome logistics constraints is to segment the blades spanwise and chordwise, which is effective, but the additional field-assembled joints result in added mass and loads, as well as increased reliability concerns in operation. An alternative to this methodology is to design slender flexible blades that can be shipped on rail lines by flexing during transport. However, the increased flexibility is challenging to accommodate with a typical glass-fiber, upwind design. In a two-part paper series, several design options are evaluated to enable slender flexible blades: downwind machines, optimized carbon fiber, and active aerodynamic controls. Part 1 presents the system-level optimization of the rotor variants as compared to conventional and segmented baselines, with a low-fidelity representation of the blades. The present work, Part 2, supplements the system-level optimization in Part 1 with high-fidelity blade structural optimization to ensure that the designs are at feasible optima with respect to material strength and fatigue limits, as well as global stability and structural dynamics constraints. To accommodate the requirements of the design process, a new version of the Numerical Manufacturing And Design (NuMAD) code has been developed and released. The code now supports laminate-level blade optimization and an interface to the International Energy Agency Wind Task 37 blade ontology. Transporting long, flexible blades via controlled flapwise bending is found to be a viable approach for blades of up to 100 m. The results confirm that blade mass can be substantially reduced by going either to a downwind design or to a highly coned and tilted upwind design. A discussion of active and inactive constraints consisting of material rupture, fatigue damage, buckling, deflection, and resonant frequencies is presented. An analysis of driving load cases revealed that the downwind designs are dominated by loads from sudden, abrupt events like gusts rather than fatigue. Finally, an analysis of carbon fiber spar caps for downwind machines finds that, compared to typical carbon fibers, the use of a new heavy-tow carbon fiber in the spar caps is found to yield between 9 % and 13 % cost savings.

17 WIND ENERGY↗

DOE OSTI2021

Progress on Optimizing Wind Farms and Rotor Designs Using Adjoints

Modern wind plants are increasingly tasked with multiple performance objectives. In addition to designing plants that maximize power output and minimize the levelized cost of energy (LCOE), the design and operation of wind plants is increasingly influenced by challenges regarding grid integration of variable generation renewables. This places a growing emphasis on making wind plants more controllable and predictable. WindSE is a Reynolds-averaged Navier-Stokes (RANS) model designed around analytical gradient and adjoint methods, with the ability to capture terrain-induced effects, as shown in Figure 1. The recent addition of an unsteady solver with an actuator line method (ALM) and ongoing work to enable massively parallel optimizations gives it a unique niche to explore coupled plant-level controls and design problems. This code is an open source python package built on the FEniCS framework that utilizes fast, parallel PETSc solvers to model fluid flow throughout wind-farm scale domains. Two recent studies performed using WindSE demonstrate the capability to optimize under a wide variety of flow conditions and objective functions. In the first, we present an optimization focused on modifying the layout of a wind farm with a fixed number of turbines for maximum total power output [1]. This study highlights the ability to quickly perform simulations using the steady Navier-Stokes solver combined with rotors represented as actuator disks while also stressing the importance of capturing terrain-induced effects. Gradient-based optimization using the RANS equations is viable due to the inclusion of efficiently computed adjoint derivatives. We interpret the physical results of the optimal layout and also discuss the computational cost of scaling to larger problems. In the second study, we present the capabilities of the unsteady Navier-Stokes solver, where rotor-blade profiles represented by actuator lines are optimized to enhance wake steering effects and overall power production [2]. We quantify the wind plant performance gains obtained from this type of simultaneous control co-design optimization as compared to optimizing the blade design and yaw independently. Figure 2 shows the differences between a baseline two-turbine system and an optimized system where we fine-tune the blade chord profile. Results and challenges from each study are quickly summarized and used to motivate the current development efforts within WindSE. Current and future work is focused on enabling higher-resolution studies with more degrees of freedom through parallelization of both the simulation and optimization algorithms. We present benchmarking results to show that WindSE performs well in both weak- and strong-scaling tests and further demonstrate that the optimizer obtains the same convergence rates in both shared- and distributed-memory environments. Using larger wind farms, we can study deep-array effects within an optimization context, allowing the use of objective functions that have been previously unstudied. As an example, we present ongoing work on a blockage metric which characterizes the loss of available kinetic energy due to wake effects from multiple upstream turbines.

adjoint optimization↗