Search NASA⌕ Search

Engineering topics

Elam, Jeffrey W.

Publications and source records attributed to Elam, Jeffrey W..

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Preliminary Results from ADRIANO2 Test Beams

A novel high-granularity, dual-readout calorimetric technique (ADRIANO2) is under development as part of the research program of T1604 Collaboration. (Talk Presented at the 19th International Conference on Calorimetry in Particle Physics (CALOR 2022), University of Sussex, Sussex, UK, 16–20 May 2022). The building block of such a calorimeter consists of a pair of optically isolated, small size tiles made of scintillating plastic and lead glass. The prompt Čerenkov light from the glass can be exploited to perform high resolution timing measurements, while the high granularity provides good resolution of the spatial components of the shower. Dual-readout compensation and particle flow techniques can be applied simultaneously to the scintillation and to the Čerenkov section, providing excellent energy resolution as well as PID particle identification. These characteristics make ADRIANO2 a 6-D detector, suited for High Energy as well as High Intensity experiments. A report on the status of the ADRIANO2 project, preliminary measurements of light yield, and current and future R&D plans by T1604 Collaboration are discussed.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2022

Tunable Solid Acid Catalyst Thin Films Prepared by Atomic Layer Deposition

Solid acid catalysts, including zeolites and amorphous silica-aluminas (ASAs), are industrially important materials widely used in the fuel and petrochemical industries. The versatility of zeolites is due to the Brønsted acidity of the bridging hydroxyl and shape selectivity that can be tailored during and after synthesis. This is in contrast to amorphous silica-alumina, where tailoring acidity is a major challenge as the Brønsted acid structure in ASA is still debated. In both cases, however, the pore size and acidity cannot be tuned independently, and this is particularly limiting in the application of biomass conversion, where zeolite pores are too small for the molecules of interest. Herein, we present a method using atomic layer deposition (ALD) to prepare thin films of solid acid materials where the ratio of Brønsted to Lewis acid sites can be tuned precisely. This capability, combined with the sub-nm pore size control afforded by ALD yields a powerful and flexible method for synthesizing solid acid catalysts inside virtually any mesoporous host. We demonstrate the utility of these materials in two acid-catalyzed reactions relevant to biomass conversion: (1) Meerwein–Ponndorf–Verley–Oppenauer (MPVO) reaction and dehydration of fructose and (2) cascade reaction of glucose to 5-hydroxymethylfurfural. Finally, we propose a plausible structure for the Brønsted acid sites in our materials based on infrared spectroscopy and solid-state nuclear magnetic resonance measurements and density functional theory calculations and argue that this same structure might apply to conventional ASAs as well.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Refractory solar selective coatings

Selective receiver coatings provide high performance for concentrated solar power applications. The solar selective coating provides high solar absorptivity (90% or greater) with low IR emissivity (0.1 or less) while maintaining stability at temperatures greater than 700° C. The coating comprises a composite of a mesoporous photonic matrix with a conformal optical coating. One example composite coating includes a mesoporous photonic coating comprising a plurality of particles having sizes between 100 nm and 2000 nm, and a conformal optical coating formed by Atomic Layer Deposition (ALD) that infiltrates the mesoporous structure of the photonic coating and comprises metal nanoparticles and an amorphous dielectric matrix.

14 SOLAR ENERGY↗
DOE OSTI2022

Method of creating structure for particle detection in time projection chambers and photodetectors

Time projection chambers are useful for high energy particle physics, nuclear physics, and astronomy. To enhance the particle detection efficiency and performance of the projection chambers functional bilayer thin film coatings based on the atomic layer deposition method are utilized. Coating material selection is based on Auger neutralization process ion induced electron emission from metallic surfaces (e.g., Mo or W) combined with a high secondary electron emission coefficient. Application of high secondary electron emission materials (e.g., MgO and CaF2) enhances the multiplication of these emitted electrons from ion induction processes. Therefore, using suitable bilayer coatings the overall TPC signal detection efficiency can be increased.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2022

Removal of Surface Carbonate from Lithium-Ion Battery Cathode Materials via Vapor-Phase Fluorination

Herein, ultrathin metal-fluoride barrier coatings on the surface of lithium-ion battery (LIB) cathodes can improve cycling stability and prevent corrosion by acidic byproducts in the electrolyte. Atomic layer deposition (ALD) is an effective method to deposit ultrathin metal fluoride coatings on LIB cathodes. Although numerous studies have demonstrated the benefit of ALD metal fluoride coatings to LIB performance, comparatively few works have examined the effect of individual ALD precursors on the cathode surface. This paper uses X-ray photoelectron spectroscopy (XPS) measurements to elucidate the surface chemical changes on LIB cathode material surfaces upon exposure to the ALD metal fluoride precursor, hydrogen fluorine pyridine (HFPy). We found a decrease in surface carbonate and an increase in surface fluoride after HFPy exposure suggesting the conversion of lithium carbonate (Li 2 CO 3 ) to lithium fluoride (LiF). This conversion is desirable given that Li 2 CO 3 degrades LIB performance, whereas LiF provides an excellent physio-chemical barrier against chemical attack during cycling. Scanning transmission electron microscopy, X-ray energy dispersive spectroscopy, and XPS measurements following HFPy exposure to Li 2 CO 3 powder revealed the formation of a conformal LiF shell around the Li 2 CO 3 particles. Finally, we confirmed the complete conversion of similar to 7 nm ALD Li 2 CO 3 films on silicon from HFPy exposure using XPS and spectroscopic ellipsometry. The elimination of problematic Li 2 CO 3 from LIB cathode surfaces and conversion into a protective LiF coating via a single precursor vapor treatment may provide a cost-effective method for enhancing LIB performance.

25 ENERGY STORAGE↗
DOE OSTI2022

Ordered nanoscale domains by infiltration of block copolymers

A method of preparing tunable inorganic patterned nanofeatures by infiltration of a block copolymer scaffold having a plurality of self-assembled periodic polymer microdomains. The method may be used sequential infiltration synthesis (SIS), related to atomic layer deposition (ALD). The method includes selecting a metal precursor that is configured to selectively react with the copolymer unit defining the microdomain but is substantially non-reactive with another polymer unit of the copolymer. A tunable inorganic features is selectively formed on the microdomain to form a hybrid organic/inorganic composite material of the metal precursor and a co-reactant. The organic component may be optionally removed to obtain an inorganic feature s with patterned nanostructures defined by the configuration of the microdomain.

Darling, Seth B.↗
DOE OSTI2022

Multifunctional transitional metal-based phosphide nanoparticles towards improved polysulfide confinement and redox kinetics for highly stable lithium-sulfur batteries

The shuttle effect and the sluggish redox kinetics of lithium polysulfides (LiPSs) are the major issues impeding the practical applications of lithium-sulfur batteries (LSBs). Herein, a highly-efficient Ni 2 P electrocatalyst supported on N, P co-doped graphene (Ni 2 P@NPG) is developed via a simple “recrystallization-self-assembly” method to address the above issues. Here, the ultrafine Ni 2 P nanoparticles ensure abundant adsorption-diffusion-conversion interfaces for accelerating LiPSs transformation and Li 2 S deposition, which extremely decreases the accumulation of LiPSs in the electrolyte and therefore prevents the migration of LiPSs. Their superior catalytic performance is demonstrated by reduced Gibbs free energy changes of rate-limiting step based on the systematic theoretical calculations and the reduced shuttle effect is tested by the three-dimensional reconstructions of Raman depth profiles. Benefiting from these synergistic effects, the LSBs with Ni 2 P@NPG modified separators present a superior cycling performance with an average capacity decay rate of 0.048 % per cycle at 1C around the 400 cycles and a high-rate capacity of 731 mAh/g at 2C. Even with a high-sulfur loading of 3.53 mg cm –2 , the cell can still contain a reversible capacity of 809 mAh/g at 0.2C with a remarkable columbic efficiency of 98.4 %.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Systems and methods for photothermal material

Chinese ink is applied on various materials and stabilized by atomic layer deposition to fabricate solar steam generation devices. The encapsulated ink has excellent photothermal properties and evaporation efficiency under simulated sunlight, holding great promise in solar evaporation device applications.

Yang, Hao-Cheng↗
DOE OSTI2022

Scalable synthesis of supported catalysts using fluidized bed atomic layer deposition

Overcoating layers deposited on the surface of heterogeneous catalysts using atomic layer deposition (ALD) have been shown to increase catalyst activity, lifetime, and selectivity. In this study, we performed Al 2 O 3 ALD and Pd ALD in a commercial fluidized bed reactor on high surface area mesoporous powder supports to create overcoated catalysts with high precursor utilization. We investigated the reaction mechanism for both Al 2 O 3 ALD and Pd ALD using in situ mass spectrometry and developed a mathematical model to understand the precursor saturation behaviors. We characterized the catalyst samples using a variety of techniques to measure the surface area, porosity, composition, and surface chemistry of the overcoated catalysts. Finally, we used propane dehydrogenation as a probe reaction to evaluate the performance of the catalysts prepared by fluidized bed ALD.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Atomic-Scale View of Redox Induced Changes for Monolayer MoO x on α-TiO 2 (110) with Chemical-State Sensitivity

Supported molybdenum oxide (MoO x ) plays an important role in catalytic transformations from alcohol dehydrogenation to transesterification. During these reactions, Mo and oxygen surface species undergo structural and chemical changes. A detailed, chemical-state specific, atomic-scale structural analysis of the catalyst under redox conditions is important for improving catalytic properties. In this study, monolayer of MoO x grown on α-TiO 2 (110) by atomic-layer deposition is analyzed by X-ray standing wave (XSW) excited X-ray photoelectron spectroscopy (XPS). The chemical shifts for Mo 2p 3/2 and O 1s peaks are used to distinguish Mo 6+ from Mo 4+ and surface O from bulk O. Excitation of XPS by XSW allows pin-pointing the location of these surface species relative to the underlying substrate lattice. Finally, measured 3D composite atomic density maps for the oxidized and reduced interfaces compare well with our density functional theory models, and collectively create a unique view of the redoxdriven dynamics for this complex catalytic structure.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Oil skimmer with oleophilic coating

A method of fabricating an coating includes providing a coating comprising a base material. The base material is coated with an inorganic material using at least one of an atomic layer deposition (ALD), a molecular layer deposition (MLD), or sequential infiltration synthesis (SIS) process. The SIS process includes at least one cycle of exposing the coating to a first metal precursor for a first predetermined time and a first partial pressure. The first metal precursor infiltrates at least a portion of the base material and binds with the base material. The coating is exposed to a second co-reactant precursor for a second predetermined time and a second partial pressure. The second co-reactant precursor reacts with the first metal precursor, thereby forming the inorganic material on the base material. The inorganic material infiltrating at least the portion of the base material. The inorganic material is functionalized with a material.

Darling, Seth B.↗
DOE OSTI2022

ALD reactor for coating porous substrates

A system and method for improved atomic layer deposition. The system includes a top showerhead plate, a substrate and a bottom showerhead plate. The substrate includes a porous microchannel plate and a substrate holder is positioned in the system to insure flow-through of the gas precursor.

Mane, Anil U.↗
DOE OSTI2022

Modification of LiMn 2 O 4 surfaces by controlling the Acid–Base surface chemistry of atomic layer deposition

In this combined theoretical and experimental study, we report the effects of Al precursor selection on the growth chemistry, interfacial structure, and electrochemistry of Al 2 O 3 coatings on spinel LiMn 2 O 4 (LMO) surfaces by atomic layer deposition (ALD). Five Al precursors, exhibiting a range of Lewis acid-base properties, were used to establish trends in the ALD Al 2 O 3 growth chemistry on LMO powders in comparison to redox-inactive planar silicon substrates. We show that the Lewis acid-base properties of the Al precursor ligands can be used to tune both the Mn oxidation states and the Al 2 O 3 coverage on the LMO surface. Density functional theory calculations are used to examine the reaction mechanism of each precursor on LMO surfaces, elucidating a correlation between the Lewis acidity of the ligands and the decomposition thermochemistry. In-depth X-ray photoelectron spectroscopy and in situ Fourier transform infrared spectroscopy measurements support these theoretical predictions and further reveal how different Al precursors modify the atomic and electronic structure near the LMO surface during ALD. While the Mn oxidation state is strongly influenced by the Lewis acidity of the precursor ligand, the surface coverage and thickness of the Al 2 O 3 coating are a more representative descriptor of the electrochemical performance measured in coin cell experiments. Finally, we show how the ligand acid-base properties of ALD precursors can be used to rationally tailor atomic layer growth mechanisms, which may enable atomic level control over the structure of functionalized interfaces for various applications related to catalysis, semiconductors, and energy storage.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Structural Changes during the Conversion Reaction of Tungsten Oxide Electrodes with Tailored, Mesoscale Porosity

In-plane tungsten oxide nanostructures, including hexagonally patterned cylinders and holes in a matrix, were fabricated via sequential infiltration synthesis (SIS) on self-assembled block copolymer templates. Using the tailored morphology and porosity of these model electrodes with in situ grazing incidence small angle X-ray scattering, the intrinsic structural change of nanoscale active materials during the conversion reaction of WO 3 + 6Li ↔ W + 3 Li 2 O was investigated at controlled electrochemical conditions. Reversible electrode volume expansion and contraction was observed during lithiation and delithiation cycles, respectively. The potential where electrode’s thickness expansion started was ~1.6 V, which is close to thermodynamically expected one for conversion reaction of WO 3 with lithium (1.65 V). The temporal evolution of the electrode volume at constant electrode potentials revealed high overpotential for bulk lithiation and slow conversion reaction kinetics, despite the tailored porosity of the SIS electrodes. Oxide cylinders showed smaller overall electrode thickness change, likely due to unconstrained lateral volume change, as compared to a matrix with holes. On the other hand, better connectivity and guided volume change of the latter electrode morphology provided improved cycling stability. Additionally, heterogeneity in an electrode, from internal pores and density gradients, was found to aggravate the fragmentation of the electrode during conversion reaction. Insights into oxide conversion reaction kinetics and the relationship between electrode mesostructure and cycling behavior obtained from this study can help guide the more rational design of conversion electrode for high performing batteries.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Molecular layer etching

A method of etching an organic or hybrid inorganic/organic material. The method etches molecular layer deposition coatings. An etching cycle comprises a first half reaction exposing the coating to a precursor. A second half reaction exposes a second precursor, removing or etching a portion of the coating.

Young, Matthias John↗