Engineering topics
Gupta, Varun
Publications and source records attributed to Gupta, Varun.
CO 2 -Responsive Fracturing Fluids for Enhanced Geothermal Systems (Final Report)
Our group has recently developed StimuFrac, a non-toxic stimuli-responsive fracturing fluid consisting of a CO 2 -reactive polymer which has shown at the lab-scale to consistently fracture rock cores at significantly lower net pressures in a range of representative geothermal pressure/temperature conditions. However, until now the mechanism/s responsible for more effective fracturing, of critical importance to optimize fracturing performance as well as strategize injection methodologies for field deployment, was not understood. In this document, we report (1) on the two main mechanisms responsible for fracturing rock at lower net pressures with StimuFrac; (2) the phase behavior of StimuFrac/CO 2 under geothermal wellbore conditions; and (3) based on high-temperature true triaxial stimulations, detailed evidence that StimuFrac/CO 2 is the best performing stimulation fluid under EGS T/P conditions as compared to water, waterless CO 2 , and CO 2 /water fracturing fluids. This is because i) it requires significantly lower volumes of CO 2 due to its reduced leak off into the formation by the crosslinked polymer solution; ii) large fractures can be generated reproducibly at both low and high CO 2 injection flow rates, and iii) the reversible (previously reported) viscosity increase of StimuFrac could be beneficial to transport proppants when they become available for EGS. These results were particularly evident for hot nearly dry rock as well as partially and nearly fully water-saturated granitic rock. GTO requires StimuFrac to be evaluated in fully water-saturated rock to determine whether the above-described performance applies under these conditions. Since (1) GTO considers there is no enough evidence for Sa different StimuFrac formulation to work below 90C (where full water-saturation in an open system is possible) and (2) no polyaxial loading frame larger than a few centimeters that can do hydraulic fracturing tests while maintaining the rock sample fully saturated with water at 200 C exists; PNNL concludes that the only way to determine if StimuFrac represents an advanced fracturing fluid alternative for EGS, is to perform a stimulation in an actual EGS reservoir.
Scalable Direct Recycling of Cathode Black Mass from Spent Lithium‐Ion Batteries
Abstract End of life (EoL) lithium‐ion batteries (LIBs) are piling up at an intimidating rate, which is alarming for environmental health. With further expected rapid growth of LIB use, the magnitude of spent battery accumulation is also expected to grow. LiNi x Co y Mn z O 2 (NCM) cathode materials are a dominant chemistry in high energy LIBs, and make up a huge portion of this waste accumulation. Direct recycling is one of the most promising ways to turn this waste to wealth, but has been limited to lab‐scale, due to lack of robustness, namely the tedious pretreatment required that involves toxic organic solvents. Herein, a process that integrates the pretreatment and relithiation of the cathode black mass is demonstrated. Cathode material from EoL electric vehicle (EV) batteries is treated in a 100 g per batch operation and the regenerated cathode active material demonstrates 100% electrochemical performance recovery, with 91% yield rate, and shows promise for further scale up. This process has the advantages of integration, scalability, and universality, which clears the barricade for direct recycling to move from lab to industry scale with considerable profitability.
Uncertainty Quantification Framework for Predicting Material Response with Large Number of Parameters: Application to Creep Prediction in Ferritic-Martensitic Steels Using Combined Crystal Plasticity and Grain Boundary Models
This paper presents an uncertainty quantification (UQ) framework for the physics-based model prediction of material response with a large number of parameters. The application problem presented in this work is that of predicting creep in Grade 91 steel at 600°C. The material response is defined with a physically based microstructural model with constitutive equations emulating several observed phenomena in Grade 91 and embodied into an explicit geometry mesoscale finite element model for prior austenite grains and grain boundaries. Creep within the grains and in grain boundaries are represented by crystal plasticity for dislocation motion and a physics-based model for cavity growth and nucleation, respectively. The creep behavior of this material is influenced by several parameters, some of which have a wide range of variation based on experimental data. UQ combined with microstructural modeling can discover the core microstructural causes of experimental variability, leading to improved materials with lower variability in critical long-term material properties. In this study, we investigate the model's uncertainty to identify material properties that may be modified during production to increase creep life and analyze different components of the crystal plasticity model for improvements. For this purpose, a quantity of interest is defined as time to minimum creep rate, which correlates well to the creep failure of the material. A deep neural network model was trained and validated to be used as a surrogate for the finite element model. Then, a variance-based sensitivity analysis is performed on the surrogate model to find the Sobol indices of the input parameters in respect to the output quantity of interest. The Sobol indices are used to reduce the dimensionality of the model. Generalized polynomial chaos expansion is used on the reduced basis models to propagate the uncertainty from the input parameters to the quantity of interest using the deep neural network surrogate model. These results are benchmarked against uncertainty propagation using Monte Carlo simulations. In conclusion, the UQ performed through the reduced basis model captures almost all the uncertainty in the model with significantly fewer simulations, making it possible to perform the UQ directly via simulations with the finite element model rather than surrogate machine-learned models.
Current Challenges in Efficient Lithium‐Ion Batteries’ Recycling: A Perspective
Abstract Li‐ion battery (LIB) recycling has become an urgent need with rapid prospering of the electric vehicle (EV) industry, which has caused a shortage of material resources and led to an increasing amount of retired batteries. However, the global LIB recycling effort is hampered by various factors such as insufficient logistics, regulation, and technology readiness. Here, the challenges associated with LIB recycling and their possible solutions are summarized. Different aspects such as recycling/upcycling techniques, worldwide government policies, and the economic and environmental impacts are discussed, along with some practical suggestions to overcome these challenges for a promising circular economy for LIB materials. Some potential strategies are proposed to convert such challenges into opportunities to maintain the global expansion of the EV and other LIB‐dependent industries.
Meshfree simulation and experimental validation of extreme thermomechanical conditions in friction stir extrusion
Abstract Friction stir extrusion (FSE) is a novel solid-phase processing technique that consolidates and extrudes metal powders, flakes, chips, or billets into high-performance parts by plastic deformation, which has the potential to save substantial processing time and energy. Currently, most studies on FSE are experimental and only a few numerical models have been developed to explain and predict the complex physics of the process. In this work, a meshfree simulation framework based on smoothed particle hydrodynamics (SPH) was developed for FSE. Unlike traditional grid-based methods, SPH is a Lagrangian particle-based method that can handle severe material deformations, capture moving interfaces and surfaces, and monitor the field variable histories explicitly without complicated tracking schemes. These aspects of SPH make it attractive for the FSE process, where in situ evolution of field variables is difficult to observe experimentally. To this end, a 3-D, fully thermomechanically coupled SPH model was developed to simulate the FSE of aluminum wires. The developed model was thoroughly validated by comparing the numerically predicted material flow, strain, temperature history, and extrusion force with experimental results for a certain set of process parameters. The validated SPH model can serve as an effective tool to predict and better understand the extreme thermomechanical conditions during the FSE process.
Experimental workflow to estimate model parameters for evaluating long term viscoelastic response of CO2 storage caprocks
Understanding the time-dependent behavior of reservoir and sealing formations is critical to assessing risks associated with geological carbon storage since time-dependent deformation strongly influences mechanical responses of some rock types. Many studies have evaluated the risk of CO2 leakage and induced seismicity by assuming poroelastic rheology in sealing formations. Few have considered viscoelastic or other time-dependent responses, where the existing literature adopts 1D models to represent long-term time-dependent responses. This is primarily because to date, the general form of a reasonable 3D time-dependent model for rocks remains unclear. In this paper, we address this unclear issue by proposing a new workflow to select constitutive modeling parameters to evaluate if a 3D viscoelastic model is reasonable using several-hour-long experimental data and a power-law response to extrapolate to the decades-long time frames of interest in geologic carbon storage. To provide experimental data, we conducted multi-level loading/unloading triaxial relaxation tests with four rock types. The experimental results showed that the maximum load relaxation observed is approximately 49%, with some rock types showing as little as 1.4%. Using a simple linear viscoelastic model, parameters were chosen such that a maximum deviation of 1.5 MPa in axial stress and 7 MPa in radial stress was attained with the extrapolated 30-year data. We found that a reasonable parameter range for the normalized elastic modulus is 0.1~2 for rocks with significant time-dependent responses and 0.01~0.06 for those with small time-dependent responses. No matter how significant time-dependent responses are for rocks considered, our results showed that the relaxation time has a general range of 1~10^10 s, whose time scale can be one or two orders higher than a time frame typically envisioned for CO2 injection projects.
A microstructure-based modeling approach to predict the mechanical properties of Zr alloy with hydride precipitates
In nuclear reactors, hydrides can form in fuel cladding due to hydrogen absorption in ZIrcaloy and cause embrittlement. This work presents a microstructure-based finite element model to predict the stress-strain response of Zircaloy containing hydrides. Quantitative microstructural details extracted from scanning electron microscopy (SEM) images were used to generate heterogeneous microstructures including the morphology and spatial distribution of hydrides. The constitutive material model for zircaloy in this study is based on crystal plasticity theory which considers the hexagonal close-packed (HCP) atomic structure of Zircaloy material. The hydrides were modeled as brittle material along with a damage model. Hydride formation inside the zircoloy matrix results in residual stress. This phenomenon is also captured in this model. A parametric study has been conducted to understand the effect of volume fraction, orientation, and lamellae thickness of the hydride phase on the mechanical properties of the overall material.
Microstructure based modeling of friction stir welded joint of dissimilar metals using crystal plasticity
We report the friction stir welding (FSW) process shows promising results in joining dissimilar metals which are otherwise almost impossible to join using traditional welding techniques. Being a new technique, the deformation and the failure mechanism of the joints made by the FSW process needs to be investigated. In this work, a joint between AZ31 Mg alloy and DP590 steel is modeled using phenomenological crystal plasticity formulation on the mesoscale in the form of a representative volume element (RVE). The interface of the two materials is modeled using a cohesive zone model. A parametric study has been performed to understand the effect of grain size and interface fracture toughness as well as strength on the mechanical performance of the joint. It was found that the grain size of AZ31 Mg alloy, as well as DP590 steel, has little effect on the overall joint performance. On the other hand, interface fracture toughness and strength have a significant impact on the mechanical properties of the joint
Determining cohesive parameters for modeling interfacial fracture in dissimilar-metal friction stir welded joints
Not Available
Alternative, Less Water-Intensive, Fracturing Fluids for Enhanced Geothermal Systems
Four fracturing fluids; water, CO2, CO2 with water, and CO2 with an aqueous solution of a CO2-reactive polymer, poly(allylamine) (PAA, 1wt%) were evaluated using a high-temperature true-triaxial fracturing apparatus and ½ foot side granite cubic samples. All three CO2-based fracturing fluids, CO2, CO2 with water, and CO2 with aqueous PAA fractured granite at higher breakdown pressures, high transient flow rates, and produce higher-conductivity fractures as compared to water. Additionally, faster pressurization rates with CO2-based fracturing fluids (obtained when fracturing at constant flow rate mode) are found to be associated with higher fracture conductivities. When partially saturating the rock sample with PAA solution followed by fracturing with CO2, the volume expansion caused by CO2-induced cross-linking of PAA leads to a faster pressure increase due to the associated stress generated and increase in viscosity. It was also found that CO2 as a fracturing fluid injected in hot dry rock (HDR) attain the highest fracture conductivity only when injected at very high flow rates, followed very closely by the CO2/PAA fracturing fluid system that generates fractures with, on average, similarly high conductivity values though independently of injection flow rate and using 1/6 of the mass of CO2 as compared to CO2 in HDR. Breakdown pressures were also similar for CO2 stimulation in HDR and CO2/PAA fluid system under identical injection flow rates. It is concluded that CO2 (when injected in HDR) and CO2/PAA are the fluids of choice for stimulation of granitic rock samples under the studied geothermal P/T conditions. CO2/PAA, however, offer the following three additional advantages; 1) it requires significantly lower volumes of CO2, 2) fracture permeability is independent of injection flow rate, and 3) the reversible (previously reported) viscosity increase is beneficial to transport proppants if they are ever developed enhanced geothermal systems.
Effect of interfacial characteristics on magnesium to steel joint obtained using FAST
Not Available
Foot-scale Evaluation of CO2-Responsive Polymer and CO2 Binary Fluid as an Alternative Fracturing Fluid for Enhanced Geothermal Systems
A foot-scale high-temperature true-triaxial fracturing apparatus was used to conduct hydraulic fracture tests on rock samples. The fracturing tests used different fluids including water, CO2, CO2 with water, and CO2 with a 1% polyallylamine (PAA)/water solution. The tests were conducted with both constant pressure injection and constant flow rate injection modes. CO2-based fracturing fluids were found to produce higher breakdown pressures, high transient flow rates, and produce higher-conductivity fractures as compared to water-based fracturing fluids. Additionally, faster pressurization rates with CO2-based fracturing fluids (obtained when fracturing at constant flow rate mode) are found to be associated with higher fracture conductivities. When fracturing with CO2-based fluids in the presence of a PAA aqueous solution, for example if the rock is saturated with 1wt% PAA in water, the volume expansion caused by CO2-induced crosslinking of PAA leads to a faster pressure increase due to the associated volume expansion and increase in viscosity. It was also found that CO2 as a fracturing fluid injected in hot dry rock (HDR) attain the highest fracture conductivity only when injected at very high flow rates, followed very closely by the CO2/PAA fracturing fluid system that generates fractures with, on average, similarly high conductivity values though independently of injection flow rate and using 1/6 of the mass of CO2 as compared to CO2 in HDR. Breakdown pressures were also similar for CO2 stimulation in HDR and CO2/PAA fluid system under identical injection flow rates. Finally, the well-known low viscosity of CO2 phase prevents the efficient transport of proppants while the reacted CO2/PAA fluid system is known to form a high viscosity binary fracturing fluid system with the potential to carry proppant in addition of being a fine fracturing fluid.
Insights into a Greener Stimuli-Responsive Fracturing Fluid for Geothermal Applications
StimuFracTM, is a non-toxic stimuli-responsive fracturing fluid consisting on a CO2-reactive polymer which has shown at the lab-scale to consistently fracture rock cores at significantly lower net pressures in a range of representative geothermal pressure/temperature conditions. In this work, we report on the two main mechanisms responsible for fracturing rock at lower net pressures with this novel fracturing fluid. The first mechanism is the additional work / overpressure generated by aqueous polymer solution during its CO2-triggered volume expansion. The second mechanism is associated to a reduction in pore invasion pressure as a result of the lower interfacial tension of StimuFrac. This reduction in pore invasion pressure results in a reduction in fracturing net pressure as previously reported. The results presented in this work illustrate the potential of StimuFrac as a greener and less-energy intensive fracturing fluid for geothermal and fossil energy production.
Interface solutions of partial differential equations with point singularity
Not Available