Search NASA⌕ Search

Engineering topics

Kombaiah, Boopathy

Publications and source records attributed to Kombaiah, Boopathy.

At least 37 records · Page 2

Strengthening Mechanisms and Deformation Behavior of Industrially-Cast and Lab-Cast Dual-Phase High Entropy Alloy

An iron-rich high entropy alloy Al 0.65 CoCrFe 2 Ni comprising of both FCC and BCC phases was designed and fabricated using induction melting at a large industrial scale and suction casting at a small lab scale. Spinodally decomposed interdendritic regions were uniformly distributed in the industrially melted alloy, and a finer dendritic structure with smaller sized spinodal structures was observed in the alloy suction cast at lab scale. The suction cast alloy fabricated at the lab scale exhibited significantly higher compressive yield strength compared to the industrially cast alloy. The relative strengthening contributions in the alloys due to solid solution, grain boundary, dislocation interactions and interphase boundary were analyzed. Dislocation hardening was the major contributor responsible for the higher strength of the SC alloy. The deformation behavior in the alloys was examined with the help of orientation image mapping. Finally, intense slip band formation at large strains in the industrially melted alloy indicates that cold working can be an effective technique to enhance the strength of the dual-phase high entropy alloy processed at a large scale.

36 MATERIALS SCIENCE↗

Nanostructured Composite Alloys for Extreme Environments

Accumulative Roll Bonding was used to process nanolayered Cu/Nb and Zr/Nb composites with varying individual layer thickness. Mechanical tests show remarkable strength as the average layer thickness decreases. Relatively high strength is preserved even at elevated temperatures. Despite differences in texture between rolling paths (longitudinally rolled-RL and cross rolled-CR) Cu/Nb, flow stresses between the resultant materials were similar. In addition, thermal conductivity does not change significantly as the interface density increases. The alloys show remarkable resistance to irradiation damage at very high doses due to stability of the interfaces. The results on Zr/Nb indicate that liquid phase chemistry resulting from thermal spikes play an important role and should be taken into account when designing alloys for extreme environments.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

3D analysis of TRISO fuel compacts via X-ray computed tomography

In this study, low-enriched uranium oxycarbide (LEUCO) and surrogate tristructural isotropic (TRISO)- coated-particle compacts with particle volumetric packing fractions of 25%, 40%, and 48% were imaged utilizing X-ray-computed tomography. Subsequent 3D image analysis identified and further quantified kernel size, sphericity, and observed porosity. In addition, the spatial distribution, coordination number, and kernel-nearest neighbors were analyzed and compared for the different packing fractions. Metrics such as observed porosity and sphericity enabled quantification and screening for abnormal kernels within TRISO compacts. Assessment of TRISO particle location confirmed and further quantified a non-uniform distribution of TRISO particles with the spatial distribution in the radial direction being roughly described as a dampened sinusoidal function. The amplitude and frequency of this non-uniform distribution increased with increasing packing fraction. Measured kernel-nearest neighbor distances indicated two regions along the radial surfaces of compacts where TRISO particles are more likely to be in intimate contact with one another. These regions were found: (1) at upper and lower faces of compacts (i.e., corners); (2) offset ~10% of a compact's length from the axial center near the exterior surface. Within these regions, small quantities of defective TRISO surrogate particles (48% packing fraction) and defective LEUCO TRISO particles (40% packing fraction) were found. No defective particles were found within 25% packing fraction LEUCO TRISO compacts.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Environmentally Assisted Cracking Research for Current and Advanced Nuclear Structural Materials

Understanding environmentally assisted cracking is an important aspect of nuclear materials research, as it provides information about failure mechanisms that lead to safety concerns or shutdowns. Idaho National Laboratory has ongoing research to understand how materials behave in the harsh nuclear environments for both the current fleet of light water reactors, as well as advanced reactors, where materials are exposed to more extreme environments. Corrosion and cracking of current materials, advanced materials, and materials formed through advanced manufacturing techniques are being examined, with particular interest in irradiation effects on corrosion and cracking, as well as the effects of environmental impurities. Testing, such as stress corrosion cracking, corrosion fatigue, and in-situ crack growth measurements, as well as a suite of characterization tools, including electron microscopy techniques and x-ray computed tomography, are being utilized to better understand the material response, limitations, and cracking mechanisms to ensure safe and reliable nuclear plants.

36 MATERIALS SCIENCE↗

Layer dissolution in accumulative roll bonded bulk Zr/Nb multilayers under heavy-ion irradiation

In this work, the heavy-ion irradiation behavior of bulk zirconium-niobium multilayered composites was investigated up to large doses. Multilayers with an average individual layer thicknesses ranging between 15 and 80 nm were synthesized by accumulative roll bonding technique. The irradiation was performed with a defocused 7 MeV Zr 2+ ion beam at 500 °C. The maximum dose achieved was ~145 dpa at the depth of ~1.5 μm from the irradiated surface. Sub-surface microstructural damage and the chemical redistribution were characterized by transmission electron microscopy and energy dispersive spectroscopy, respectively. Irrespective of the layer thicknesses, the irradiation condition caused layer instability and the extent of damage varied with the dose levels. Doses lesser than ~60 dpa caused layer fragmentation and greater than ~60 dpa resulted in layer dissolution. The chemical mixing of layers occur to a depth of ~1 μm, consuming multiple bi-layer periods. Despite the elevated irradiation temperature (500 °C) and a slightly positive heat of mixing (+6 kJ/mol), no phase separation was observed and single-phase was retained in the mixed region. The results demonstrate that chemical mixing was facilitated by the liquid phase miscibility of Zr and Nb, which propelled the interdiffusion within the thermal spikes towards mixing.

36 MATERIALS SCIENCE↗

Post-irradiation examination of legacy high burnup fuel to support safety testing

Safety/transient testing to evaluate performance under off-normal conditions is an essential pillar for both the development of Accident Tolerant Fuels (ATF) and the optimization of fuel operation economics beyond current discharge burnups. Among other factors, the successful interpretation of the transient testing results relies upon the knowledge of the initial conditions of the test, including the characteristics of the fuel system under scrutiny. When testing pre-irradiated material, the assumptions that the fuel and the cladding still have the same properties as in the pre-irradiation stage is obviously wrong and could affect the results of the test. This is particularly true the more burnup accumulates in the fuel rod and irradiation progresses. The knowledge of the initial microstructure of both fuel and cladding allows a clearer interpretation of the subsequent transient testing results, provides validation of the physical phenomena underlying the model predictions and eliminates the uncertainties related to the limited knowledge of the sample status before the test. One example is the phenomenon of fine fragmentation that occurs in Light Water reactor (LWR) fuel. During a Loss of Coolant Accident (LOCA) or Reactivity Initiated Transient (RIA) the fuel can severely fragment. During LOCA, high burnup fuel tend to finely fragment, which has raised safety concerns due to the increased likelihood of dispersal of such small particles once the cladding has burst and due to the increased fission gas release. Therefore, efforts have been devoted to the assessment of a pulverization threshold that could determine the conditions under which fine fragmentation is predominant. However, the lack of information regarding the initial conditions of the fuel, and the connections between those conditions and the pre-transient irradiation history, have hindered the development of a fully mechanistic fragmentation and pulverization criterion. The empirical relationships rely on conservative estimations, due to the lack of information on critical material properties and characteristics. More generally, experimental evidence of the irradiation-induced modifications at microstructural scale are necessary to determine the behavior of the material at the macroscopic scale, with the latter being the one of technological interest. Significant progress has been made in the last two decades in the developments of analytical materials science techniques that can be applied to highly radioactive materials, such as high burnup fuels. The availability of new techniques and the improvement of existing ones has enabled investigations previously not possible that can deepen the understanding of the fuel characteristics and properties at high burnup. The better knowledge of material behavior and irradiation-induced phenomena could help the prediction of its performance. In this context, the scope of the present work is to apply a wide portfolio of advanced characterization techniques to determine properties that are relevant for safety and performance. The results are interpreted in the context of engineering scale post-irradiation examinations and available information on the irradiation conditions.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

First-principles calculation of lattice distortions in four single phase high entropy alloys with experimental validation

Exceptional properties of high entropy alloys (HEAs) are attributed to the disordered random solid solution of multiple alloying elements. Despite numerous studies, the fundamental understanding at the electronic and atomic levels is still missing. We report a comparative study of four fcc HEAs of NiFeCoCr and NiFeCoCrX (X = Mn, Cu, or Pd) based on ab initio calculations using large supercells with 500 atoms in equal composition. After fully optimizing their structures using the VASP package, their electronic structure, interatomic bonding, partial charge distribution, and mechanical properties are calculated and compared, revealing the intricate interdependence among them. A novel parameter based on the quantum mechanical metric for internal cohesion, the total bond order density (TBOD), is used to interpret the calculated properties. The highest TBOD is found in Cantor alloy NiFeCoCrMn but lower in NiFeCoCrPd. The atomic radii vary depending on their local chemical environment. The resulting lattice distortions is validated experimentally in NiFeCoCrMn and NiFeCoCrPd. Moreover, modeling of Cu and Pd clustering in the supercell shows they have lower total energy in agreement with the observation of Cu-enhanced nano-participates in NiFeCoCrCu and Pd-induced concentration wave in NiFeCoCrPd HEAs.

36 MATERIALS SCIENCE↗

Structure of the pellet-cladding interaction layer of a high-burnup Zr-Nb-O nuclear fuel cladding

Here, structure of the pellet/cladding-interaction (PCI) layer of a high-burnup nuclear fuel with niobium-bearing cladding was investigated using modern transmission electron microscopy (TEM) techniques. Morphology of the PCI consisted of uniform zirconia layer on the cladding side and finger-like features towards to the ceramic fuel. The PCI layer showed a complex microstructure that constitutes three distinct zirconia layers formed by two zirconia phases. From cladding to fuel, monoclinic, tetragonal, and another tetragonal phase were determined via TEM diffraction patterns and precession electron diffraction (PED) using ASTAR microscopy platform (AMP). Characterizations showed that monoclinic and tetragonal phases close to the cladding were crack-free, but the tetragonal layer adjacent to the fuel contained cracks and pores. Presence of the monoclinic layer suggested that its formation involved the gaseous diffusion of oxygen below threshold dose of fission product damage before the fuel/cladding contact occurred. Furthermore, high-resolution TEM revealed compound phase of (U,Zr)O 2 at fringes of zirconia fingers on the fuel side.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Near-surface modification of defective KTaO 3 by ionizing ion irradiation

The synergistic effect of nuclear (S n ) and electronic (S e ) energy loss observed in some ABO 3 perovskites has attracted considerable attention due to the real possibility to modify various near-surface properties, such as the electronic and optical properties, by patterning ion tracks in the defective near-surface regions. In this study, we show that low-energy ion-induced disordering in conjunction with ionizing ion irradiation (18 MeV Si, 21 MeV Ni and 91.6 MeV Xe) is a promising approach for tailoring ion tracks in the near-surface of defective KTaO 3 . Experimental characterization and computer simulations reveal that the size of these latent ion tracks increases with S e and level of pre-existing damage. These results further reveal that the threshold S e value (S e th ) for track creation increases with decreasing pre-damage level. The values of S e th increase from 5.02 keV nm -1 , for a pre-existing fractional disorder of 0.53 in KTaO 3 , to 10.81 keV nm -1 for pristine KTaO 3 . Above these thresholds, amorphous latent tracks are produced due local melting and rapid quenching. Below a disorder fraction of 0.08 and S e ≤ 6.68 keV nm -1 , the synergistic effect is not active, and damage accumulation is suppressed due to a competing ionization-induced damage annealing process. These results indicate that, depending on S e and the amount of pre-existing damage, highly ionizing ions can either enhance or suppress damage accumulation in KTaO 3 , thus providing a pathway to tailoring defects states. Comprehending the conflicting roles of highly ionizing ions in defective ABO 3 oxides is vital for understanding and predictive modeling of ion-solid interactions in complex oxides, as well as for achieving control over ion track size in the near-surface of defective KTaO 3 .

36 MATERIALS SCIENCE↗

Microstructural and Micro-Chemical Evolutions in the Irradiated UCO Fuel Kernels of AGR-1 and AGR-2 TRISO Fuel Particles

AGR-1 and AGR-2 TRISO fuel particles were fabricated with slightly different fuel kernel chemical compositions, modified fabrication processes, different fuel kernel diameters, and changed 235U enrichments. To correlate those differences with the fuel kernel responses to neutron irradiations in terms of irradiated fuel microstructure, fission products chemical and physical states, and fission gas bubble evolutions, extensive microstructural and analytical characterizations were conducted. The studies used a state of art transmission electron microscopy (TEM) equipped with Energy-dispersive X-ray spectroscopy (EDS) of four silicon solid-state detectors which have super sensitivity and fast speed. The TEM specimens were prepared from selected AGR-1 and AGR-2 irradiated fuel kernels exposed to safety testing after irradiation. The particles were chosen to represent a representative irradiation conditions with a fuel burnup within the range from 10.8 to 18.6% FIMA, and the time-average volume-average temperatures vary from 1070 to 1287°C. The 235U enrichment was 19.74 wt.% for the AGR1 fuel kernels and 14.03 wt.% for the AGR-2 fuel kernels. The TEM results show that there were significant microstructural reconstructions in the irradiated fuel kernels for both the AGR-1 and AGR-2 fuels. There are four major phases including fuel matrix of UO2 and UC, U2RuC2, and UMoC2 in the irradiated AGR2 fuel kernel. Zr and Nb form solid solution in the UC phase. UMoC2 phase often shows a detectable concentration of Tc. Pd was found to mainly locate in the buffer layer or to be associated with fission gas bubble within the UMoC2 phase. The EDS maps qualitatively show that the rare-earth fission products (Nb, et al.) preferentially reside in the UO2 phase. In contrast, in the irradiated AGR1 fuel kernel, no U2RuC2 or UMoC2 precipitates were positively identified. Instead, there is a high number of rod-shape precipitates enriched with Ru, Tc, Rh, and Pd observed in the fuel kernel center and edge zone. The difference of microstructural and micro-chemical evolutions in irradiated fuel kernels between the AGR-1 and AGR-2 TRISO fuel particle may result from a combined factor of irradiation temperature, fuel geometry and chemical composition. However, the irradiation temperature probably play a more deterministic role. Limited electron energy loss spectroscopy (EELS) characterizations on the AGR2 fuel kernel show that there is nearly no carbon in the UO2 phase while a small fraction of oxygen was detected in the UC/UMoC2 phase.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Heterogeneous creep deformation behavior of functionally graded transition joints (GTJs)

Dissimilar metal welds (DMWs) made between ferritic steels and austenitic alloys are used extensively in high-temperature power plant components. These DMWs experience premature creep failure in the ferritic steel’s heat affected zone (HAZ), close to the weld interface. Steep variations in microstructure and chemical composition across the dissimilar weld interface have been the contributing factors for the failure. Graded transition joints (GTJs), developed by functionally grading the chemical composition in layers, have been proposed as potential candidates to replace DMWs. In this research, GTJ coupons were fabricated between 2.25Cr-1Mo steel and Alloy 800H base material using two filler materials: (i) Inconel 82 and (ii) P87. These samples were aged at 600°C for 2000h to accelerate high-temperature microstructural evolution seen in service conditions, before subjecting them to short-term (~1 month) creep tests. Surface strains were measured using digital image correlation (DIC) technique to extract creep strain rates at different locations within GTJs. Both the GTJs exhibited heterogeneous creep strain distribution. Creep strain accumulated in the FGHAZ of 2.25Cr-1Mo steel, similar to type IV failure associated with Cr-Mo steel weldments. Microstructure based creep model framework was developed to describe the discrete creep strain rates observed in various 2.25Cr-1Mo steel regions of GTJs.

36 MATERIALS SCIENCE↗

Advanced Microscopy Report on UCO Fuel Kernels from Selected AGR-1 and AGR-2 Experiments

A variety of neutron irradiation experiments were completed at Idaho National Laboratory (INL) on tristructural isotropic (TRISO) coated particles contained in a graphitic matrix as part of the Advanced Gas Reactor (AGR) fuel development and qualification program. Although the initial advanced microscopy and microanalysis studies on AGR-1 particles focused predominantly on the SiC layer?s role as the main fission-product containment, studies were further expanded to evaluate UCO kernels of selected AGR-1 and AGR-2 coated particles. Fuel kernels tested in the AGR-1 and AGR-2 experiments is composed of a mixture of UO2 and UC, with a nominal as-fabricated stoichiometry of UO1.37 C0.35 and UO1.43 C0.39, respectively. These as-fabricated kernel-stoichiometry values are determined at the completion of kernel fabrication and do not account for any changes that will occur during the subsequent coating and compacting processes.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Advanced Electron Microscope and Micro Analysis of TRISO coated Particles: FY2020 Overview

Objectives Understanding Effects of Irradiation on TRISO layers Fission product chemistry and behavior in UCO kernel Identify and Understand Fission Product Transport Mechanisms in TRISO Coated Particles Outcomes and Impact Impact on Performance Improve Predictive Behavior Modeling Kernel Behavior: Release from kernel; release from whole particle Known Fission Product Transport Mechanisms

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

From suppressed void growth to significant void swelling in NiCoFeCr complex concentrated solid-solution alloy

Void swelling can result in dimensional instability and undermine the safe operation of nuclear reactors. Current strategies to inhibit void swelling mainly focus on enhancing defect absorption and recombination by introducing high-density defect sinks. Complex concentrated solid-solution alloys (CSAs), including high-entropy alloys, can withstand severe radiation damage due to their inherent chemical complexity without interfaces. However, the underlying mechanisms for void suppression in CSAs are far from clear. In this research, we studied the void evolution with respect to irradiation depths, doses, and temperatures in equiatomic NiCoFeCr under 3 MeV Ni ion irradiations. At relatively low doses (16 and 54 displacements per atom, dpa), voids form mainly outside of the ion-damaged region, and void formation in the peak damage region is suppressed, leading to negligible swelling. However, with further increase of dose (86 up to 250 dpa), significant void growth occurs in the peak damage region and extended dislocation lines dominate instead of short dislocation lines and loops formed at lower doses. From 500 to 700 °C, the dislocation density decreases while dislocations grow. Although the overall void swelling increases dramatically from 500 to 580 °C at 54 dpa, void growth in the peak damage region is still suppressed. The transition from suppressed void growth to significant void swelling is attributed to dislocation evolution and local chemical inhomogeneity (enrichment of Fe/Cr in the matrix) at higher doses. Our study shows that controlling element diffusion and defect evolution through tuning chemical complexity can further enhance the swelling resistance of CSAs.

36 MATERIALS SCIENCE↗

Material Properties of Non-Irradiated Zircaloy 4 in Support of ASME Code Acceptance for Pressure Vessel Design

A program underway at Oak Ridge National Laboratory (ORNL) to support private industry design of a system for production of 99Mo includes review of Zircaloy-4 (Zry-4) properties as a potential material for a primary vessel in the system. Because Zry-4 is not a material specified in the ASME Boiler and Pressure Vessel Code, a review has been performed to obtain the necessary data in the non-irradiated condition from the literature and from additional testing of Zry-4 to enable creation of tables of material properties required for ASME Code Section III Article ND-3000 design. A strategy for an in-vessel surveillance program is also recommended for early detection of potential corrosion and irradiation degradation issues during operational life of the vessel. Additionally, the ASME Code Section II, Part D was reviewed to ascertain the requirements for proposing a new material for Code approval. A plate of Zry-4 procured by ORNL was used to obtain tensile properties that were used as the basis for determining the maximum allowable stresses applicable to the vessel design. The materials properties of primary interest for ASME Code application are tensile properties, fracture toughness, fatigue, and five specific physical properties required by the Code for approval of a new material. The literature review revealed that all reported experimental data showed tensile strengths to substantially exceed the minimum specifications in ASTM B352. Sufficient fracture toughness and fatigue data are available to conclude that Zry-4 has sufficient fracture and fatigue resistance in the unirradiated condition for vessel design and operation. Of the physical properties reviewed, only thermal conductivity revealed a discrepancy that is recommended for further review. A surveillance program plan has been developed that is probably the maximum that would need to be implemented for the specific vessel design considered. Once adequate non-irradiated and irradiated data are available from preproduction testing of the Zry-4 and weld metal and HAZ materials, the program could be reduced to reflect that either initial properties are very good and/or the effects of embrittlement appear to be minimal. However, the overall design of a surveillance program is, of course, also dependent on the ASME Code design class for the pressure vessel.

Nanstad, Randy↗