Search NASA⌕ Search

Engineering topics

Nemeth, William

Publications and source records attributed to Nemeth, William.

At least 19 records

Microwave Annealing for Fast and Effective Hydrogen Activation in Polycrystalline Silicon Passivating Contacts

Hydrogenation is a crucial step in the fabrication of high-efficiency silicon solar cells. In this study, the effectiveness of hydrogen activation is demonstrated via microwave annealing of hydrogen-rich dielectrics coated on poly-Si passivating contacts. This method is compared with conventional hydrogenation techniques, such as annealing in N2 in the presence of a hydrogen-rich source (such as hydrogenated aluminum oxide (AlOx:H), hydrogenated silicon nitride (SiNy:H), or a AlOx:H/SiNy:H stack). Key improvements observed include a reduction in J0 from 30 to <5 fA cm-2, an increase in iVoc from 690 to >730 mV, and an enhancement in effective lifetime (teff) from 0.6 to ~3.5 milliseconds on phosphorus-doped poly-Si/SiO2 passivating contact samples. With a very short annealing time of ~1-2 min, the samples passivated by AlOx:H, SiNy:H, or the stack show similar performance to samples subjected to 30 min of nitrogen annealing. Photoluminescence (PL) spectra corroborate the findings regarding the hydrogenation of the poly-Si layer and the c-Si substrate, with an increase in PL intensity after microwave annealing. Ultimately, this work suggests that microwave annealing could be a promising addition, offering flexibility to traditional firing hydrogenation processes.

hydrogenation↗

High Temperature Copper Metallization: Demand, Hurdles and Reliability

As newer cells structures come online, the pressing need to replace silver in the metallization pastes has renewed interest in alternative technologies employing base metals. Copper typically leads the charge with its abundance and lower cost but has faced numerous obstacles from relatively higher oxidation and diffusion rates which can damage the lifetime of the devices. In this study, a low-cost alternative to silver metallization pastes has been shown on PERC cells. The screen printable copper paste can be fired in air at temperatures >500 degrees C, and the impact of processing conditions and equipment on the performance and reliability of 274 cm2 cells have been evaluated. Through damp heat testing of micro-modules using 16 cm2 cells, routes that can lead to both the failure and success of durable contacts have been demonstrated.

copper↗

Optical Modeling of Polysilicon: TOPCon PV

Determine how film thickness changes with different deposition methods. Analyze relationship between film thickness and optical constants. The deposition rate of intrinsic polysilicon is higher during initial deposition then begins to slow down as deposition time increases. Longer depositions of polysilicon are more crystalline in structure than shorter depositions. N-type doping of polysilicon is more crystalline in structure than p-type doping, despite similar film thicknesses.

Bruggeman effective media approximation↗

Characterization of Tunnel Oxides in TOPCon Solar Cells

The 1.12 nm thickness for the tunnel oxide layer is near the optimal range described by Choi et al. This thickness should be effective at enabling quantum tunneling; however, it is slightly lower than the reported optimal range which could negatively impact the passivation of the poly-Si interface. An appropriate balance between the two functions must be met to optimize efficiency. Follow up work could focus on testing the optimal range for tunnel oxide thickness in TOPCon solar cells, as well as improving the manufacturing process to produce better control of film thickness. This work could be extended into more advanced TOPCon solar cells including double or triple stack structures, as well as experimental pinhole designs.

SOLAR ENERGY↗

Screen-Printed Complex Ag Inks for Si HJT Metallization

Metallization using reactive metal inks has recently attracted significant research interest due to its advantages in cost of materials and manufacturing, while still achieving performance comparable to traditional fire-through particle pastes. Here, we present for the first time the use of reactive silver (Ag) inks via industrial screen-printing and inkjet printing methods for the metallization of different Si surfaces used in tunneling oxide passivating contacts (TOPCon) and Silicon heterojunction (SHJ) solar cells. Printed Ag lines exhibit a conductivity of ~5 Mu O·cm, which is approximately 3 times that of bulk Ag (1.59 µO·cm). The printed metal has a thickness of ~0.5-1.5 Mu m, an order of magnitude smaller than the current fire-through metal finger thickness (~15 Mu m). Contact resistivity measurements of the screen-printed and inkjet-printed samples on a transparent conducting oxide (TCO) surface show a very low value of ~0.2-12 mO·cm 2. Photoluminescence images of the metallized samples demonstrate minimal surface passivation degradation compared to the non-metallized areas (?iVoc <3.5 mV). Scanning electron microscopy images (SEM) reveal the structure of the printed metals on the Si surfaces as porous but much denser than fire-through Ag by nanoparticle paste. In the final presentation, we will showcase our results of printing these reactive Ag inks on high-efficiency heterojunction and TOPCon solar cells with full-area M6 wafers. Additionally, the adhesion of these reactive Ag inks on different Si surfaces according to ASTM D3359-17, as well as the performance of solar cells after standard IEC 61215 freeze/thaw and damp heat tests, will be presented. These new metal inks show promising potential as an alternative to the currently dominant particle-based pastes, offering lower Ag consumption and lower processing temperatures without compromising performance.

heterojunction solar cells↗

Crystalline Si Surface Passivation with Nafion for Bulk Defects Detection with Electron Paramagnetic Resonance

Here, in monocrystalline Si (c-Si) solar cells, identification and mitigation of bulk defects are crucial to achieving a high photoconversion efficiency. To spectroscopically detect defects in the c-Si bulk, it is desirable to passivate the surface defects. Passivation of the c-Si surface with dielectrics such as Al 2 O 3 and SiNx requires deposition at elevated temperatures, which can influence defects in the bulk. Herein, we report on the passivation of different Czochralski (Cz) Si wafer surfaces by an organic copolymer, Nafion. We test the efficacy of the surface passivation at temperatures ranging from 6 to 473 K to detect bulk defects using electron paramagnetic resonance (EPR) spectroscopy. By comparing with state-of-the-art passivation layers, including Al 2 O 3 and liquid HF/HCl, we found that at room temperature, Nafion can provide comparable passivation of n-type Cz Si with an implied open-circuit voltage (iV oc ) of 713 mV and a recombination current prefactor J o of 5 fA/cm 2 . For p-type Cz Si, we obtained an iV oc of 682 mV with a J o of 22.4 fA/cm 2 . Scanning electron microscopy and photoluminescence reveal that Nafion can also be used to passivate the surface of c-Si solar cell fragments scribed from a solar cell module by using a laser. Consistent with previous studies, analysis of the EPR spectroscopy data confirms that the H-terminated surface is necessary, and fixed negative charge in Nafion is responsible for the field-effect passivation. While the surface passivation quality was maintained for almost 24 h, which is sufficient for spectroscopic measurements, the passivation degraded over longer durations, which can be attributed to surface SiO x growth. These results show that Nafion is a promising room-temperature surface passivation technique to study bulk defects in c-Si.

14 SOLAR ENERGY↗

Defect control strategies for Al 1- x Gd x N alloys

Tetrahedrally bonded III-N and related alloys are useful for a wide range of applications from optoelectronics to dielectric electromechanics. Heterostructural AlN-based alloys offer unique properties for piezoelectrics, ferroelectrics, and other emerging applications. Atomic-scale point defects and impurities can strongly affect the functional properties of materials, and therefore, it is crucial to understand the nature of these defects and the mechanisms through which their concentrations may be controlled in AlN-based alloys. In this study, we employ density functional theory with alloy modeling and point defect calculations to investigate native point defects and unintentional impurities in Al 1-x Gd x N alloys. Among the native defects that introduce deep midgap states, nitrogen vacancies (V N ⁠) are predicted to be in the highest concentration, especially under N-poor growth conditions. We predict and experimentally demonstrate that V N formation can be suppressed in thin films through growth in N-rich environments. We also find that Al 1-x Gd x N alloys are prone to high levels of unintentional O incorporation, which indirectly leads to even higher concentrations of deep defects. Growth under N-rich/reducing conditions is predicted to minimize and partially alleviate the effects of O incorporation. The results of this study provide valuable insights into the defect behavior in wurtzite nitride-based alloys, which can guide their design and optimization for various applications.

36 MATERIALS SCIENCE↗

Metal-Complex Inks for Lower Cost and Improved Passivation for Silicon Photovoltaic Metallization

This contribution introduces the silicon PV community to screen-printable metal-complex inks that potentially will reduce Ag usage in Si PV metallization to one-quarter and costs to one-third that of traditional particle-based pastes while also improving passivation. Metal-complex inks are formulated using a Tollen’s reaction to produce inks with a high percentage of diamminesilver (I) cations (22 wt %) in a solution of acetate and formate anions. When printed and dried, labile ammonia ligands evaporate, leaving behind silver cations which, when reduced by formate anions and acetic acid, plate out silver and silver acetate. When annealed to just 300 °C a dense metallic silver film forms with excellent conductivity, and adhesion to silicon. When compared to traditional particle-based screen-printing pastes, the metal-complex inks are much denser, have higher conductivity, use less Ag, and are a fraction of the cost. Importantly, the inks anneal from 90 – 450 °C allowing for improved passivation schemes compared with fired SiNx. This contribution highlights first experiments on the improved passivation of metallized poly-Si/SiO2 passivated contacts using metal-complex Ag inks.

Young, David L. (ORCID:0000000340970493)↗

Loss Analysis and Performance Optimization Pathways of 729-mV Voc Si Solar Cells with Poly-Si on Locally-Etched Dielectric Passivating Contacts

In this article, the loss analysis of silicon solar cells with polysilicon on locally-etched dielectric passivating contacts with Voc=729.0 mV and efficiency=22.6% has been presented. Experimentally, nano-pinholes were introduced in SiO x (2.2 nm) and SiO x /SiN y (2.2 nm/8nm) stack using metal-assisted chemical etching (MACE). SunSolve and Quokka3 were used to simulate the experimental solar cell and investigate the optical and electrical power losses. Simulations suggest maximum power loss occurs due to recombination and resistive losses in the bulk (~0.76 mW/cm2) followed by power loss due to rear contact recombination (~0.35 mW/cm2). Recombination at the front surface also contributes to 0.24 mW/cm2. The effect of improving the bulk lifetime and lowering the recombination current density at the rear side on Voc, FF and hence, efficiency has been investigated. Further, advanced structures have been proposed to minimize recombination and parasitic absorption to achieve higher Voc and Jsc of the solar cells with locally-etched dielectric passivating contacts.

contacts↗

A New Method for the Evaluation of Majority and Minority Carrier Contact Resistivity of Polysilicon on Oxide Contacts

In this contribution we present a novel technique for characterizing the majority and minority carrier contact resistivity in polysilicon on oxide passivating contacts. Traditionally, contact resistivity is measured through the Transfer Length Method (TLM). This method presents difficulties when measuring the minority carrier contact due to the presence of a blocking diode which prevents current flow between the pads. Our novel method is performed by creating a unipolar device which has the same contact on both sides (either symmetric n-type or symmetric p-type) and metalizing the device with a grid on one side, and a full metal contact on the back (the same pattern that will be used in a final cell). We then measure the resistance across the device at increasing illumination. Since the resistivity of the wafer is a function of carrier density, when increasing illumination, the wafer resistivity decreases. We can then fit modeling equations to the measured resistivity and extrapolate the fit to infinite illumination where only the contact resistivity is measured to accurately measure both the minority and majority carrier contact resistivity.

current measurement↗

Defect Characterization of Monocrystalline Silicon Solar Cells with Polysilicon Passivated Contact Using Electrically-Detected Magnetic Resonance (EDMR) Spectroscopy

As the c-Si based solar cell efficiencies are approaching over 26%, it is becoming critical to characterize the low concentrations of the defects – as low as 10^10-10^11 cm-3 (for e.g., iron contamination in high-lifetime Ga-doped wafers3 and n-type wafers), and further reduce them. Also, atomistic level understanding of the mechanisms of the low concentration process-induced-defects and reliability limiting defects (such as light and elevated temperature induced degradation, surface passivation degradation) is needed to design the mitigation strategies. The conventional characterization techniques are limited due to their detection limitations. Some of the techniques based on lifetime spectroscopies can still be used for low concentration characterization however, they are based on estimations and theoretical models and hence, indirect and cannot fully reveal information about the microscopic mechanism of the defects. Thus, we present the application of an ultrasensitive magnetic resonance-based technique for the direct spectroscopic detection of the defects in Si PV - electrically detected magnetic resonance (EDMR). In this work, we aim to focus on establishing a process flow for fabrication of minicells with (miniature replica of the larger-area cells) and setting up the routine for EDMR measurements on them with the EDMR instrumentation capability at NREL. For the EDMR measurements, sample size is limited by the dimensions of sample holder tube (width less than 3.2 mm, active area - 20 mm). Thus, we have designed c-Si based minicells with polysilicon (poly-Si) passivated contacts same as the larger-area cells that we fabricate in our group at NREL. We also modified our minicell process flow for fabricating the textured minicells for preserving the texture during processing and taking care of the laser-ablation edge damage which can significantly affect the performance of such small devices. We have achieved comparable performance on these newly fabricated minicells as that of our 4 cm2 devices with same structure (comparable VOC, JSC, FF). We also conducted EDMR measurements on the minicells and observed a distinct EDMR signal at g-value ~2.005 at temperatures 30K and above, as shown in Fig. 2. We associate this signal to the presence of silicon dangling bonds based on the g-value. We also observed an EDMR signal at g-value ~1.998 at temperature ~5K. The origin of this signal is still being investigated. Thus, we show the proof of concept of minicells and EDMR measurements with which we now aim to study some of the unknown defects in silicon solar cell devices.

EDMR↗

Understanding Hydrogen Passivation Mechanism in Poly-Si Passivating Contacts: Insights from Effusion Studies

Silicon PV is the dominant PV technology, and captures >95% world market share, supporting -100 GW/year. Diffused and passivated pn junctions along with other rear side passivation technologies are the mainstream technologies and will continue to remain so in the coming decades. Passivated contacts, using tunnel oxide passivation stacks at the rear side, will gain market share from about 10% in 2022 up to 58% within the next 10 years. Most mature approaches use passivating layers of hydrogenated Al2O3 and SiNx. LPCVD SiNx provides less hydrogen for passivation compared to PECVD SiNx but can retain the hydrogen up to higher temperatures which is beneficial for firing. Although SiNx provides large amount of hydrogen, this doesn't necessarily translate to good passivation. AlOx:H contributes to retaining H at higher temperatures. Water molecules are also detected during H-effusion and may play a role in passivation of the oxide/wafer interface.

effusion study↗

High-Performance Passivating Contacts for Si PV Based on Engineered, Doped Nanopinholes through Dielectric Layers

We present a novel, industrially relevant method to fabricate high-performance poly-Si passivating contacts for Si PV. Passivating contacts based on SiOx/poly-Si layer stacks have been implemented in record-efficiency homojunction Si solar cells. In this technology, the carrier transport through a surface-passivating SiOx is enabled either by quantum-tunneling or nanopinholes. The doped poly-Si layer provides charge-carrier selectivity. Previously, the ISFH research group demonstrated a record 26.1% efficient Si homojunction cell, where transport pinholes in ~2 nm SiOx were produced by thermal breakdown at > 1000 degrees C, which is hard to control and is surface morphology-dependent. At room temperature, our new process uses electroless plating of Ag nanoparticles, followed by metal-assisted chemical etching. Nanogalvanic corrosion yields < 20 nm-wide nanopinholes in an insulating > 2 nm SiOx layer. The nanopinholes are filled by a heavily doped a-Si:H overlayer. We drive in the dopants into the Si wafer with subsequent high-temperature annealing. Preferential incorporation of dopants at pinhole locations results in nanoscale p+/n or n+/n junctions near the wafer interface. Each heavily-doped nanoscale pinhole junction collects and transports photogenerated carriers to the cell metal contacts. The density of the engineered nanopinholes can be tuned over a wide range which is critical for optimization of device performance. The same nanogalvanic corrosion principles can be applied to produce doped transport pinholes in well-passivating thick dielectric SiOx/SiNy stacks. Importantly, our process does not rely on thermal breakdown of the dielectric layers and can be applied to textured wafers resulting in Si solar cells with > 20% conversion efficiency.

dielectric layer↗

Self-Assembled Monolayer Procedure to Pattern Silicon Passivated Contacts

We utilize hexamethyldisilazane (HMDS)-based self-assembled monolayers to pattern polysilicon (polySi) passivated contacts. We find process conditions that allow for etching frontside n/polySi between fingers, thereby increasing Jsc. Importantly, the Voc does not degrade indicating the additional process steps do not introduce defects or impurities. HMDS layers remain on the surface for metallization without detriment to transport.

hexamethyldisilazane↗

Loss Analysis and Performance Optimization Pathways of 729-mV VocSi Solar Cells with Poly-Si on Locally-Etched Dielectric Passivating Contacts

In this article, the performance analysis of a 22.5% efficient polysilicon on silicon oxide (poly-Si/SiOx) passivated contact solar cells with deliberately introduced pinholes using metal-assisted chemical etching (MACE) has been performed with the help of optical analysis using Sunsolve and electrical analysis using Quokka3. The power loss is maximum due to recombination and resistive losses in the bulk (~0.76 mW/cm2 ) followed by power loss due to rear contact recombination (~0.35 mW/cm2 ). Recombination at the front surface also contributes to 0.24 mW/cm2. The effect of improving the bulk lifetime and lowering the recombination current density at the rear side on Voc, FF and efficiency has been investigated.

MACE↗

Self Assembled Monolayers for Passivated Contacts

Passivated contacts mitigate defects typically encountered due metallization of solar cells. We deposit amorphous silicon (a-Si:H) on an oxidized silicon wafer via PECVD and anneal at high temperature to crystallize into polysilicon passivated contact. One drawback is the absorption of the polysilicon between grid fingers, so removal of this material is desirable to maximize Jsc. Alternatively, interdigitated back contact cells rely on a gap between n- and p- fingers, which is commonly etched to ensure electronic isolation. We utilize a self assembled monolayer (SAM) using hexamethyldisilazane (HMDS) as a precursor to pattern and etch amorphous silicon (a-Si:H) and polysilicon without the need for photoresist. Ultraviolet light exposure oxidizes the HMDS by photocleaving the organic groups [1] of the SAM leaving a patterned SiO2. Directly soaking this in TMAH will eventually etch the SAM and the silicon, where the SiO2 serves as an etch mask. Inversely, a dilute HF dip selectively etches this SiO2 and the SAM remains. A subsequent soak in TMAH selectively etches the underlying silicon, where the SAM serves as an etch mask. Importantly, we find that the SAM can remain intact for metallization, where we measure 10 mO-cm2 specific contact resistivity on n-type polysilicon.

passivation↗

Hydrogen Stability and Bonding in SiN x and Al 2 O 3 Dielectric Stacks on Poly-Si/SiO x Passivating Contacts

Polycrystalline Si on SiO x passivating contacts enables some of the highest efficiency single-junction Si photovoltaic devices, but the high-temperature firing process needed for industrial metallization can significantly reduce passivation. We show that after firing, the implied open-circuit voltage, iV oc , for the Al 2 O 3 /SiN x /poly-Si/SiO x /c-Si stack is 20-30 mV higher than the SiNx/Al 2 O 3 /poly-Si/SiO x /c-Si stack and therefore provides better passivation of the SiO x /c-Si interface. Using effusion measurements and Fourier transform infrared spectroscopy, we demonstrate that more than twice as much hydrogen is retained in the dielectric up to the peak firing temperature of ~800 degrees C for Al 2 O 3 -capped structures. If the Al 2 O 3 layer is not present in the stack, after firing, the iVoc is lower by 50-100 mV compared to Al 2 O 3 /SiN x or SiN x /Al 2 O 3 stacks. These studies will inform future work on the role of dielectrics in aiding the passivation of poly-Si/SiO x passivating contacts.

08 HYDROGEN↗

Controlled Dielectric Breakdown to Form Pinhole Passivating Contacts

This contribution explores an alternate route to forming pinhole-based poly-Si/dielectric/c-Si passivating contacts. The method utilizes controlled dielectric breakdown or electroforming to produce nanoscale pinholes in a thick (non-tunnelling) dielectric which, when annealed, allows dopant atoms to pass from doped poly-Si through the pinholes and into the c-Si wafer, forming conductive pathways. We show that the pinholes lose passivation after electroforming but can be repassivated with a forming gas anneal. N-type contacts show contact resistivities of ~20 mOhm-cm2, but p-type contacts are ~100 mOhm-cm2. Devices show a distinct kink in the J-V curve indicative of a barrier to transport. The method can be expanded to optimized dielectric passivation stacks (not just thin, single layers) and can be formed in parallel over the faces of the wafer in selected areas (pinholes only under the grid lines).

CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND SU↗