Search NASA⌕ Search

Engineering topics

Nemeth, William

Publications and source records attributed to Nemeth, William.

At least 37 records · Page 2

Electrical Analysis of Pulsed Laser Annealed Poly-Si: Ga/SiOx Passivating Contacts

In this contribution, we examine Ga hyper-doped poly-Si/SiOx contacts realized by pulsed laser melting (PLM). Here, we use Ga as a novel p-type dopant and B as a conventional dopant to induce non-equilibrium doping using an excimer laser. We perform simulations to visualize the maximum melt depth profiles within the poly-Si, with a goal of distributing dopants close to the tunneling oxide, but at the same time preserving the passivation. Hall measurements show that sheet resistance for B is lower than Ga due to its higher solid solubility limit in Si. After comparing the Hall active dopant concentration with the chemical concentration obtained by SIMS measurement, we show nearly 100% activation B activation reaching 10^21 cm-3, while only ~20% activation for Ga. Nevertheless, we achieve active doping concentrations of Ga in poly-Si six times higher than its solid solubility limit in Si (~10^19 cm-3). We compare our Hall mobilities with values in the literature for c-Si and show that B mobilities in laser-treated poly-Si are close to that of the literature value for B, while Ga mobilities are lower, possibly due to additional scattering channels within grain boundaries and deformed lattice. We also compare our results on PLM samples with conventional furnace annealed samples, and we show much higher percent activation and mobilities. Previously, we showed a low contact resistivity of 35.5 +/- 2.4 m..omega..cm2. Here, we further confirm this result by scanning spreading resistance microscopy and Kelvin force nanoprobe microscopy. We demonstrate that our poly-Si: Ga/nCz contact exhibits large drift and diffusion currents under normal cell operating voltage, which widens the laser processing window for a good metal/poly-Si/c-Si contact.

high-efficiency solar cells↗

Pinhole electrical conductivity in polycrystalline Si on locally etched SiN$_y$/SiO$_x$ passivating contacts for Si solar cells

State-of-the-art monocrystalline Si (c-Si) solar cells require passivating contacts to achieve a high degree of charge-carrier separation and collection. In this work, we focus on boron-doped polycrystalline Si on locally etched silicon nitride/silicon oxide (PLENO) passivating contacts. In PLENO contacts, excellent surface passivation is provided by the ~10 nm dielectric bilayer, while pinholes in the dielectric bilayer, that are filled with doped polycrystalline Si, provide charge-carrier selectivity and transport. During PLENO fabrication, etch undercut in the dielectric bilayer occurs. Here, using electrical characterization and microscopies, we show that undercut causes pinholes to be electrically resistive in PLENO. A processing sequence that eliminates the undercut in the final PLENO structure results in electrically conductive pinholes with low contact resistivity.

14 SOLAR ENERGY↗

Mechanism of Hydrogen Passivation in Passivated Contact Si Solar Cells

In this abstract, we discuss the mechanism of hydrogen passivation on symmetrical n-Si/ultra-thin SiO2/polySi structures. The hydrogen was introduced from different hydrogen-containing dielectric layers (AlOx:H and SiNx:H and their stacks), as well as by forming gas anneal (FGA). The effusion of hydrogen both from the dielectric layers and in the underlying poly-Si was explored using a quadrupole mass spectrometer (QMS) and FTIR spectroscopy. We show that the strength of hydrogen bonds depend on the deposition technique as well as hydrogenation mechanism. While a PECVD SiNx:H loses hydrogen at a peak temperature of ~450 degrees C, LPCVD SiNx:H, although having less hydrogen compared to PECVD, effuses at a peak temperature of ~850 degrees C. This becomes important to maintain passivation of passivated contacts after firing of metal contacts at high temperatures. On the other hand, it has been observed that SiNx:H provides larger amount of hydrogen to poly-Si after FGA compared to FGA treated AlOx:H, which acts as a capping layer and helps in retaining the hydrogen up to higher temperatures.

hydrogen bonding configuration↗

Metal-Complex Inks for Lower Cost and Improved Passivation for Silicon Photovoltaic Metallization

This contribution introduces the silicon PV community to screen-printable metal-complex inks that potentially will reduce Ag usage in Si PV metallization to one-quarter and costs to one-third that of traditional particle-based pastes while also improving passivation. Metal-complex inks are formulated using a Tollen's reaction to produce inks with a high percentage of diamminesilver (I) cations (22 wt %) in a solution of acetate and formate anions. When printed and dried labile ammonia ligands evaporate, leaving behind silver cations which, when reduced by formate anions and acetic acid, plate out silver and silver acetate. When annealed to just 300 degrees C a dense metallic silver film forms with excellent conductivity, and adhesion to silicon. When compared to traditional particle-based screen-printing pastes, the metal-complex inks are much denser, have higher conductivity, use less Ag, and are a fraction of the cost. Importantly, the inks anneal from 90 - 450 degrees C allowing for better passivation schemes than fired SiNx. This contribution highlights first experiments on the improved passivation of metallized poly-Si/SiO2 passivated contacts using metal-complex, Ag inks compared with particle-based, fired pastes.

metal-complex ink↗

High-voltage monocrystalline Si photovoltaic minimodules based on poly -Si/SiO x passivating contacts for high-power laser power conversion

By using photovoltaic cells under high-intensity laser illumination, much higher photoconversion efficiencies are obtained than under the solar spectrum. Here we demonstrate a monocrystalline Si based minimodule to convert laser light into electricity using edge-illuminated Si "minicells" based on polysilicon on silicon oxide passivating contacts. Ten fully metallized devices were stacked in series and illuminated from the edge, creating a high-voltage, low-current minimodule that mitigates resistive and Auger-Meitner losses. The minimodule shows a high open-circuit voltage of >5 V when tested under 1-Sun illumination and >7 V at higher illumination intensities when tested with a flash simulator. The fill factor in these minimodules is limited by shunting at low illuminations but reaches a maximum of ~78% for higher illumination intensities >40 Suns (current density >1200 mA/cm 2 ), indicating that the minimodules are not limited by series resistance up to 40 Suns. Under 1000 nm monochromatic light, we measure efficiencies >40% at > 40 Suns equivalent illumination, showing the potential of passivated contact Si cells for laser power conversion.

14 SOLAR ENERGY↗

Structure and Electronic Properties of Mesopores in Si PV Devices with PLEO Contacts

All current state-of-the-art silicon photovoltaic (PV) devices employ some flavor of passivating contact structure to minimize detrimental recombination while providing good conductivity. These properties are most often provided by a dielectric layer (SiNx, Al2O3, or SiOx) that is in contact with the crystalline silicon (c-Si) substrate. The effectiveness of these layers is heavily dependent on the nanoscale structure of both the dielectric layers and the crystalline silicon interface. As an example, the tunneling probability for charge carriers across thin SiOx layers, a process that is critical to maintain high conductivity, is extremely sensitive to the SiOx thickness. SiOx with a thickness below 2 nm readily allows charge carrier tunneling, whereas it is impeded for greater thicknesses. In the latter case it has been shown that modifications to the thermal processing schedule can induce disruptions, or pinholes, in thick SiOx layers that allow transport of charge carriers while maintaining excellent passivation. However, this requires higher temperatures processes that may inhibit widespread adoption by industry. Recently, another option has been presented that may circumvent the necessity for high temperature processing, namely metal assisted chemical etching (MACE). MACE relies on deposition of Ag nanoparticles onto the SiOx layers with subsequent electroless etching to form mesopores in the SiOx layers that are analogous to the pinholes created with high temperature processing. The size and density can be controlled based on the Ag nanoparticle deposition conditions. The resulting contact structure is known as polysilicon on locally etched oxide (PLEO) contacts. The nanoscale structure of the mesopores in PLEO contacts define the device level observables such as recombination current (Jo) and junction resistance. In this work we present atomic resolution transmission electron microscopy (TEM) analysis of mesopores in PLEO contacts formed with a different processing conditions to connect provide insight into how the nanoscale structure of the SiOx layer influences PV device properties. Additionally, we have previously used electron beam induced current (EBIC) to probe local transport properties in Si PV devices with a SiOx layer containing pinholes due to high temperature processing. Using EBIC we were able to directly show the enhance charge carrier transport through the pinholes. Here we also employ EBIC to study non-uniformities in charge carrier recombination and transport associated with mesopores in PLEO contacts and compare these results with our previous work on devices with pinholes in the SiOx formed through high temperature processes. The products of this work provide critical information that is required to both further optimize performance of Si PV devices with PLEO contact and to drive future adoption of this technology by industry.

ENGINEERING,SOLAR ENERGY↗

Nanopinhole Passivating Contact Si Solar Cells Fabricated with Metal-Assisted Chemical Etching

Monocrystalline Si (c-Si) solar cells with passivating contacts based on doped polycrystalline Si (poly-Si) on ≈2.0 nm silicon oxide (SiO x ) require >1000 °C thermal processing to create conducting pinholes in the SiO x layer. However, this high thermal budget can induce bulk defects in the Czochralski c-Si wafers used as the cell absorber layer. We demonstrate that pinholes can instead be created using metal-assisted chemical etching on planar or textured morphologies, at room temperature. This wet process creates up to 200 nm wide conducting pinholes that are directly observed with transmission electron and atomic force microscopies. High-performance hole-selective poly-Si/SiN y /SiO x and electron-selective poly-Si/SiO x passivating contacts are fabricated and implemented in laboratory-scale solar cells. This process development significantly broadens the range of passivation layer materials, their thicknesses, and surface morphologies, which enables the design of poly-Si contacts with superior passivating quality.

14 SOLAR ENERGY↗

Metal oxide barrier layers for terrestrial and space perovskite photovoltaics

Perovskite photovoltaics are attractive for both terrestrial and space applications. Although terrestrial conditions require durability against stressors such as moisture and partial shading, space poses different challenges: radiation, atomic oxygen, vacuum and high-temperature operation. Here we demonstrate a silicon oxide layer that hardens perovskite photovoltaics to critical space stressors. A 1-um-thick silicon oxide layer evaporated atop the device contacts blocks 0.05 MeV protons at fluences of 10 15 cm -2 without a loss in power conversion efficiency, which results in a device lifetime increase in low Earth orbit by x20 and in highly elliptical orbit by x30. Silicon-oxide-protected Cs 0.05 (MA 0.17 FA 0.83 ) 0.95 Pb(I 0.83 Br 0.17 ) 3 ) (MA, methylammonium; FA, formamidinium cation) and CsPbI 2 Br cells survive submergence in water and N,N-dimethylformamide. Furthermore, moisture tolerance of Sn-Pb and CsPbI 2 Br devices is boosted. Devices are also found to retain power conversion efficiencies on exposure to alpha irradiation and atomic oxygen. So, this barrier technology is a step towards lightweight packaging designs for both space and terrestrial applications.

14 SOLAR ENERGY↗

Mitigation of shunt in poly -Si/SiO$_{x}$ passivated interdigitated back contact monocrystalline Si solar cells by self-aligned etching between doped fingers

Polycrystalline silicon on silicon oxide (poly-Si/SiO x ) passivating contacts can be used for ultra-high-efficiency interdigitated back contact (IBC) monocrystalline silicon solar cells. We evaluate the use of intrinsic poly-Si for the region that isolates the p- and n-type fingers at the back side of IBC devices. To mitigate shunt across the isolation region between the doped p- and n-type fingers, we demonstrate self-aligned subtractive processing by etching the poly-Si in the isolation region using SF6 plasma followed by etching in a tetramethylammonium hydroxide (TMAH) solution. After removal of the poly-Si, the isolation region was passivated with SiN x and Al 2 O 3 , which resulted in an 11.7% increase in the fill factor in a 19.8% efficient device. Furthermore, we evaluate the limitations of this device through Suns-V oc analysis and simulations using SunSolve and Quokka3 solar cell simulation software. Through Quokka3, we show that the most significant efficiency losses come from junction recombination current (J 02 ) in the isolation region between doped fingers. We predict that the cell efficiency can be most improved with reduced J 02 through better isolation of heavily doped fingers by etching the isolation region deeper into the bulk or through enhanced surface chemical passivation in this region.

14 SOLAR ENERGY↗

Pulsed Laser Annealed Ga Hyperdoped Poly‐Si / SiO x Passivating Contacts for High‐Efficiency Monocrystalline Si Solar Cells

Polycrystalline Si ( poly ‐Si)‐based passivating contacts are promising candidates for high‐efficiency crystalline Si solar cells. We show that nanosecond‐scale pulsed laser melting (PLM) is an industrially viable technique to fabricate such contacts with precisely controlled dopant concentration profiles that exceed the solid solubility limit. We demonstrate that conventionally doped, hole‐selective poly ‐Si/SiO x contacts that provide poor surface passivation of c ‐Si can be replaced with Ga‐ or B‐doped contacts based on non‐equilibrium doping. We overcome the solid solubility limit for both dopants in poly ‐Si by rapid cooling and recrystallization over a timescale of ∼25 ns. We show an active Ga dopant concentration of ∼3 × 10 20 cm −3 in poly ‐Si which is six times higher than its solubility limit in c ‐Si, and a B dopant concentration as high as ∼10 21 cm −3 . We measure an implied open‐circuit voltage of 735 mV for Ga‐doped poly ‐Si/SiO x contacts on Czochralski Si with a low contact resistivity of 35.5 ± 2.4 mΩ cm 2 . Scanning spreading resistance microscopy and Kelvin probe force microscopy show large diffusion and drift current in the p ‐ n junction that contributes to the low contact resistivity. Our results suggest that PLM can be extended for hyperdoping of other semiconductors with low solubility atoms to enable high‐efficiency devices.

14 SOLAR ENERGY↗

Characterization of Engineered Pinholes in Dielectric Stacks of High-Performance Poly-Silicon Passivating Contacts

Passivating contact structures are expected to be implemented in > 50 % of industrially manufactured silicon photovoltaics produced over the next decade. One type of passivating contact utilizes a c-Si/dielectric/doped poly-Si layer stack. In cases where the dielectric layer/s are thick enough to impede tunneling of charge carriers, it was shown that disruptions (pinholes) in the dielectric are required to facilitate transport.[1] Pinholes in SiOx layers have typically been formed via high temperature annealing that allows localized breakup of this layer. This approach has drawbacks; 1) high temperature annealing increases cost and 2) pinhole formation is sensitive to both the SiOx thickness and wafer surface morphology making control of density and dimensions difficult. Recently, an alternative method of pinhole formation relying on metal assisted chemical etching (MACE) was shown to allow control over pinhole areal densities.[2] Such control is critical as both the density and dimensions of the pinholes determine saturation current density and contact resistivity. The contacts formed with the MACE process are known as polysilicon on locally etched oxide or PLEO and also result in low saturation current densities and low contact resistivity due to SiOx passivation and engineered pinhole enabled charge carrier transport, respectively. Photovoltaic devices with efficiencies greater than 20 % have recently been produced with these contacts, demonstrating the viability of contacts with engineered pinholes. Experimentally, preferential local collection of excess charge carriers has been observed and definitively connected to thermally induced pinholes in thick SiOx layers within c-Si/SiOx/poly-Si contact structures.[3] Recent work has shown that enhanced local collection of excess carriers can result from enhanced diffusion of dopants through pinholes in SiOx layers.[4] This study was restricted to simulation and characterization of poly-Si with the same dopant type as the c-Si substrates. In this work we focus our analysis on boron doped poly-Si with different stacks of dielectric layers (PLEO and PLENO where the N refers to a SiNy layer on top of the SiOx) on n-type crystalline silicon. This provides insight into how engineered pinholes affect charge collection across the p-n junction. Like previous observations of locally enhanced carrier transport through thermally induced pinholes, the EBIC images in Figure 1 shows that engineered pinholes in PLENO (1a) and PLEO (1b) also exhibit locally enhanced carrier transport at pinhole locations (bright spots in the images). We will also present detailed correlative nanoscale structural and chemical analysis using TEM imaging and EELS analysis with sample preparation guided by EBIC imaging. This allows us to connect the density and dimensions of engineered pinholes with charge carrier transport and measured photovoltaic device parameters. Our findings will accelerate the adoption of PLEO and PLENO contacts in industrially manufactured photovoltaic devices.

EBIC↗

Spectroscopic Investigation of Shallow Hole Traps in Ga- and B-doped Czochralski Silicon: Insight into Light-Induced Degradation

We report the minority carrier lifetime in B-doped Czochralski (Cz) Si declines upon carrier injection due to light-induced degradation (LID), which is attributed to the formation of a recombination-active boron-oxygen complex. Ga-doped Cz Si does not undergo LID. Previously, we showed that B-doped Cz Si undergoes a transition from paramagnetic to diamagnetic due to LID. Herein, we show that Ga-doped Cz Si remains paramagnetic upon carrier injection. This suggests that either the shallow hole traps that are formed in B-doped Cz Si are absent in Ga-doped Cz Si, or the negative-U centers in Ga-doped Cz Si do not transform into a recombination-active configuration, because the shallow acceptor trap state is shallower than the Ga acceptor level in the forbidden gap. In contrast to B-doped Cz Si, the defect signatures in Ga-doped Cz Si do not change upon light exposure, as detected by both electron paramagnetic resonance and deep-level transient spectroscopy.

14 SOLAR ENERGY↗

Electrical Analysis of Pulsed Laser Annealed Poly-Si:Ga/SiOx Passivating Contacts

High-efficiency single crystalline silicon (c-Si) solar cells require precise control of dopant diffusion profiles and highly active doping concentrations through thermal annealing. Conventional furnace annealing has been successfully employed for dopant diffusion in aluminum back-surface field (Al-BSF), passivated emitter and rear contact (PERC), and Topcon cells. However, furnace annealing limits some next-generation polycrystalline silicon (poly-Si) on SiOx passivating contacts. This limitation largely affects p-type passivating contacts by not being able to: 1) control the dopant diffusion accurately to prevent B segregation at the SiOx and c-Si interface; and 2) provide highly activated doping concentrations for low contact resistivity. In this contribution, we use a nanosecond excimer laser to examine the passivation quality and electrical performance of both B- and Ga-doped poly-Si/SiOx passivating contacts. The core of this method is to take advantage of the nonequilibrium nature of the anneal through rapid melting and recrystallizing the poly-Si in a short timescale and to achieve doping concentrations above the solid solubility limit. Simulations were performed on polished surfaces to visualize the doping diffusion profiles under different laser conditions, and secondary ion mass spectrometry (SIMS) was used to verify the experimental diffusion profiles post pulsed laser melting (PLM). The results show the dopant diffusion profiles can be tuned precisely through PLM. The electrical analysis using VdP-Hall measurements reveals that the active doping concentration reached 10^21 cm-3 for B and ~2×10^21 cm-3 for Ga in poly-Si, far exceeding their solid solubility limit in Si, with a nearly 100% dopant activation achieved for B, and 20% for Ga. This highly activated dopant profile results in a low contact resistivity of <15 mO·cm^2 for B-doped contacts and <40 mO·cm^2 for Ga-doped contacts. We demonstrate that the passivation quality of the laser annealed contacts shows a linear dependency with the laser energy density and the number of pulses. PLM was also performed on random pyramid textured samples, and we found that preferential melting exists for the tips of pyramids, which can be pursued further for selective pinhole opening. Additionally, we perform thermal stability tests of these hyperdoped passivating contacts and show that under certain laser conditions, the B-doped samples exhibit good thermal stability with near full activation for temperatures up to 800°C. Lastly, we transfer this technique to a larger area by overlapping laser spots and show uniform passivation quality and electrical performance. We are currently implementing this PLM annealed p-type passivating contacts into double-side back-junction poly-Si/SiOx passivating contact devices. Our results show that PLM can not only enable the next generation of high-efficiency c-Si photovoltaics technology but can also benefit the c-Si integrated circuit industry through hyperdoping other semiconductors with atoms that may otherwise have a low solubility.

doping diffusion profile↗

Nafion Passivation of c-Si Surface and Edge for Electron Paramagnetic Resonance

Effective surface passivation of crystalline silicon (c-Si) surface by reducing the carrier recombination rate has led to modern c-Si solar cells with efficiencies > 25% in both laboratory and industrial settings. Typical mainstream surface passivation techniques include high-temperature silicon oxide (SiOx), amorphous silicon (a-Si:H), hydrogen-rich silicon nitride (SiNx), and aluminum oxide (Al2O3) [1]. They have demonstrated excellent surface recombination velocity of < 1 cm/s owing to both chemical passivation (via the hydrogen saturation of Si dangling bonds at the c-Si surface), and field-effect passivation (via the band bending from the fixed charge of the dielectric layers). Recently, several groups have studied solution-based organic materials for c-Si passivation, including bis(trifluoromethane)sulfonimide (TFSI), polystyrenesulfonate, and Nafion [2, 3] via spin or dip coating. All films were processed at ambient room temperature, and a high lifetime of 12 ms, as well as a low saturation current density (J0) of 16 fA/cm2, have been demonstrated using Nafion passivation [2]. However, despite the air instability, Nafion has several advantages when introduced to PV applications: (a) Wafer quality can be measured at high throughput after several process stages. (b) It is compatible with PL mapping, compared to HF liquid passivation which cannot be performed in room ambient. (c) Nafion process is fast and poses fewer constraints on process complexity, and cleanness, compared to Al2O3 and a-Si:H passivation. (d) Nafion is the ideal room temperature passivation, which can be applied onto a small fragment of a degraded module to investigate microscopic mechanisms when studying degradation mechanisms. Edge passivation is needed for advanced characterization tests such as Electron Paramagnetic Resonance (EPR), Electrically Detected Magnetic Resonance (EDMR), Deep Level Transient Spectroscopy (DLTS), local cell current-voltage (J-V), and Suns-Voc. In such cases, the laser-damaged minicell edges will obscure the true degradation mechanisms, and Nafion can effectively passivate them without causing further degradation through elevated-temperature processes. In this contribution, we show the passivation results of Nafion on bare nCz and compare it with a Al2O3 witness. We highlight the importance of edge pre-treatment before Nafion to achieve good passivation. We show that Nafion can reach decent passivation without undergoing high-temperature processes. We also explore the temperature dependency of Nafion through photoluminescence (PL) study and demonstrate the application of Nafion under cryogenic temperature (~6 K) through EPR. Our results reveal that Nafion can reduce surface and edge Si dangling bonds at low temperatures. Thus, it can be used as an effective room temperature passivation technique for advanced characterization methods.

c-Si↗

Room Temperature, Dip Coating Organic Passivation for c-Si Surfaces

Surface passivation of crystalline Si (c-Si) to reduce recombination rate is crucial to obtain high-efficiency c-Si solar cells. A fast passivation technique that can be performed at room temperature is needed when studying the degradation behaviors using various characterization methods to not destroy the degraded states. In this contribution, we explore Nafion via dip coating on n-type Cz wafers. We show that both the Nafion concentration and the conditions of surface and edge affect the passivation quality, and we achieve excellent passivation quality of iVoc of 716 mV, with a saturation current density (J0) of 7 fA/cm2. Additionally, electron paramagnetic resonance (EPR) shows Nafion can be used under cryogenic temperature and reveals the reduction of Si dangling bond after Nafion treatment.

dielectric solar cell↗

Controlling Pinhole Radius and Areal Density in a-Si/SiOx Using Metal-Assisted Chemical Etching

Polysilicon on silicon oxide (poly-Si/SiOx) passivating contacts with predominant charge-carrier transport via pinholes are currently prepared via a>1000 degrees C thermal step to induce oxide break-up. Herein, we develop the precursor of a pinhole-enabled poly-Si/SiOx contact utilizing room temperature metal-assisted chemical etching (MACE) to form pinholes in the SiOx. The pinholes were created via electroless Ag nanoparticle (Ag NP) deposition followed by the MACE of intrinsic amorphous hydrogenated silicon (a-Si:H) on SiOx, creating isolated mesopores through the film stack. By varying the MACE etching solution (HF:H2O2) concentration, we were able to vary the pinhole areal density over four orders of magnitude (104-107 cm-2). We observed the Ostwald ripening of the Ag NP to enable control over the pinhole radii. Our work demonstrates proof-of-concept for a-Si:H/SiOx with mesopores across the film stack, which may serve as precursor for the development of poly-Si/SiOx passivating contacts of both polarities.

MATERIALS SCIENCE,SOLAR ENERGY↗

Restored Passivation after Complete Removal of Front Poly-Si Between the Grid in Poly-Si/SiO2 Front/Back Cells

This work explores the use of wet chemical etching to completely remove the front poly-Si layer between grid lines of a front/back poly-Si/SiO2 passivated contact device. The purpose of the work is to provide excellent passivation under the metal grid, but to also maximize Jsc by eliminating optical absorption in the front poly-Si. We show that after a high temperature anneal to distribute carriers in the poly-Si/SiO2/c-Si interface all of the poly-Si can be removed selectively with TMAH, using the SiO2 as an etch-stop layer. The etched surface can be repassivated back to its original level with the addition of a SiNx/Al2O3 stack grown on the preserved tunnelling oxide layer followed by a short forming gas anneal. Using symmetric 100 - 200 nm intrinsically doped poly-Si/SiO2 on textured n-type wafer templates we show absolute device efficiency enhancement from 15% to 21% by increasing the Jsc by 12 mA/cm2 after removing the front poly-Si and repassivating while effectively preserving the Voc, and FF of the device. IQE values are similar to PERC devices in the short wavelength range.

etching↗