Search NASA⌕ Search

Engineering topics

Teng, Fei

Publications and source records attributed to Teng, Fei.

At least 37 records · Page 2

Microstructural and phase changes in alpha uranium investigated via in-situ studies and molecular dynamics

A deeper knowledge of thermally induced microstructural and phase evolution in nuclear metallic fuel can be obtained using novel in-situ microscopic analyses. Such studies can provide information on the dynamics of phase transitions which is not possible with conventional postmortem characterization (post-irradiation examination). In this work, the behavior of alpha uranium (α-U) was investigated via in-situ heating tests in a transmission electron microscope. Here, the main objective is to understand the microstructural and phase changes, such as defect annihilation and ß phase formation and retention, observed in reactor in-pile transient studies at the Transient Reactor Test facility. Indeed, defect migration and rearrangement were observed within the α phase starting at 673 K; α→ß phase transition was observed between 773 K and 1,073 K during the heating ramp (which is in the temperature window reported for α→ß transition temperatures). Recrystallization and formation of nano grains was observed at high temperatures (over 1,073 K). Such recrystallization was possibly related to the formation of the γ phase. Finally, it was indeed observed that the ß phase (but not γ phase) was retained at room temperature upon rapid cooling. Molecular dynamics studies support these experimental results and shows that the γ phase of pure uranium cannot be retained at room temperature if not stabilized with the addition of an alloying element.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

The effects of radiation-induced grain subdivision and dislocations on the fracture properties of uranium dioxide

Microcantilever bending tests were applied on uranium dioxide samples irradiated by 84 MeV Xe ions. Depending on the initial grain sizes, different levels of grain subdivision and dislocation development were observed near the irradiated surface. These radiation damage features were shown to degrade the fracture properties of both samples. The fundamental aspects of the radiation-microstructure-property relationships were discussed in this paper, taking a holistic consideration of the microcantilever bending data, fractography and microstructures. The separate effects of the irradiation-induced grain subdivision and dislocations on the fracture initiation and propagation of uranium dioxide were discussed. In conclusion, it was observed that radiation-induced dislocations and grain subdivision, without the presence of Xe bubbles co-located with the defects, cause reductions in the Young's modulus, fracture strain, and fracture stress, and a transition to intergranular fracture.

36 MATERIALS SCIENCE↗

Irradiation Effects on Stability of δ-UZr2 phase in U-50 wt% Zr Alloy

U-50wt%Zr is a candidate metallic nuclear fuel with potential application in light water reactors due to its excellent thermal properties and high radiation tolerance. The Zr-rich UZr fuels possess greater swelling resistance and fission gas release characteristics compared with U-rich UZr fuels. In this current study, the δ-phase U-50wt%Zr is proton irradiated at room temperature to 1 displacement per atom (dpa) to provide insights on phase stability under irradiation conditions. High resolution characterization of Transmission Electron Microscopy (TEM) and Atom Probe Tomography (APT) characterization techniques are used to elucidate microstructural changes due to irradiation. TEM and APT results show highly oriented bcc β-Zr-rich platelet precipitates nucleating adjacent to α-U phases inside the UZr 2 matrix. Formation of this platelet morphology is characteristic of Widmänstatten structure which can be attributed to a variety of factors such as differences in thermal expansion coefficient between the phases, grain size, alloy composition, and cooling rate. The phases present are distinctly different than those observed through in situ annealing, but irradiation accelerates diffusion and phase separation kinetics. These microstructural changes in U-50wt%Zr are different from those achieved by pure thermodynamic or high temperature heavy ion irradiation experiments. Finally, our work, together with previous ones, highlight the necessity to study the U-Zr phase diagram under non-equilibrium thermodynamics conditions to support this material's deployment as a viable nuclear fuel form.

36 MATERIALS SCIENCE↗

Detailed characterization of a PWR fuel rod at high burnup in support of LOCA testing

Experimental investigations of the fuel microstructure and volatile fission products along the pellet of a high burnup specimen (local burnup 76 GWd/tHM) have been conducted to support future transient testing. Detailed microscopy examinations have been carried out at different length scales. Transmission electron microscopy has highlighted a significant amount of damage across the entire radius with the formation of networks of dislocations. The optical and scanning electron microscopy determined the formation of three zones in the pellet with different characteristics. An intermediate region with no grain subdivision, lower porosity than the central zone porosity and high retained fission gas in nanometric bubbles and in the matrix was present between r/r0 ˜ 0.55 and 0.8. The high retention of gas in this region might suggest that the region will be prone to fine fragmentation, in addition to the HBS. An abrupt transition in the structure was observed at mid radius, with a third region developing from the mid radius to the pellet center. In this part of the pellet, metallic and grey phases with size between hundreds of nanometers and a few micrometers have formed at grain boundaries. The majority of fission gas has been released from the grain matrix and the original grains have polygonised, forming sub-grain domains separated by low-angle grain boundaries. No final explanation can be given for the polygonization occurring in the center, but on the basis of the irradiation history and the analysis of all the post irradiation examination (PIE) data, it is postulated that the polygonization within the original grains is an effect of dynamic recovery occurring at high temperature in the fuel center.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Measurement of grain boundary strength of Inconel X-750 superalloy using in-situ micro-tensile testing techniques in FIB/SEM system

Grain boundaries (GBs), known as two-dimensional defects, are omnipresent in polycrystalline metallic alloys and thus influence a wide range of mechanical properties under different environmental conditions like irradiation and corrosion. Therefore, quantifying the strength of individual GBs is critical for understanding the degradation of mechanical properties of materials under different conditions. In this study we developed an efficient approach for the fabrication of micro-tensile specimens with a GB almost perpendicular to the tensile direction, which is expected to advance the development of individual GB tensile testing at micro or nanoscale in a wide scope of materials. Further, an in-situ cantilever micro-tensile testing method was developed and used to quantify the strength of a Σ3 GB in Inconel X-750 with the combination of finite element modeling. The average ultimate tensile strength (UTS) of a non-irradiated Σ3 GB is estimated at around 1.4 GPa, comparable to that of a neutron-irradiated Σ3 GB with a dose of ~1.5 dpa (1.3 GPa). Moreover, the in-situ push-to-pull micro-tensile testing technique developed in this work provides valuable insights into the high-angle GB deformation and fracture behavior. This method generates qualitatively similar ductility behavior before and after neutron irradiation as the bulk material testing. However, the ductility and UTS values obtained from this method are different from bulk measurements due to vastly different specimen dimensions.

36 MATERIALS SCIENCE↗

Transmission Electron Microscopy based Characterization of a U-20Pu-10Zr Fuel Irradiated in Experimental Breeder Reactor-II

U-Pu-Zr metallic fuels are important fuel candidate for future advanced and/or test reactors. To better understand fuel performance and guide future fuel development, a U-20Pu-10Zr (in weight) metallic fuel irradiated in the Experimental Breeder Reactor was revisited using advanced electron microscopies. This fuel was irradiated to a burnup of 7.6 % at a peak cladding temperature of 521 °C. In this research, several transmission electron microscopy samples were extracted from different but representative radial locations of the fuel cross section using focused ion beam technique. Phase identification and chemical analysis with sub-micron spatial resolution was carried out using scanning transmission electron microscopy. Multiple phenomena that are critical to fuel performance, such as Zr phase and its distribution in a different matrix, were revealed in an unpreceded and highly detailed manner. An improved understanding of fuel reconstruction in U-Pu-Zr metallic fuel under reactor irradiation is provided.

36 MATERIALS SCIENCE↗

On the differential representation and color-kinematics duality of AdS boundary correlators

The AdS boundary correlators and their dual correlation functions of boundary operators have been the main dynamic observables of the holographic duality relating a bulk AdS theory and a boundary conformal field theory. We show that tree-level AdS boundary correlators for generic states can be expressed as nonlocal differential operators of a certain structure acting on contact Witten diagrams. We further write the boundary correlators in a form that is very similar to flat space amplitudes, with Mandelstam variables replaced by certain combinations of single-state conformal generators, prove that all tree-level AdS boundary correlators have a differential representation, and detail the conversion of such differential expressions to position space. We illustrate the construction through the computation of the boundary correlators of scalars coupled to gluons and gravitons; when converted to position space, they reproduce known results. Color-kinematics duality and BCJ relations can be defined in analogy with their flat space counterparts, and are respected by the scalar correlators with a gluon exchange. We also discuss potential approaches to the double copy and find that its direct generalization may require nontrivial extensions.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Small-scale mechanical testing and characterization of fuel cladding chemical interaction between HT9 cladding and advanced U-based metallic fuel alloy

Fuel cladding chemical interactions (FCCI) occurred on the interface between the nuclear metal fuel and cladding is the primary cause of cladding wastage, weakening cladding mechanical integrity, and placing fuel and cladding at risk. Although the microstructural and phase information of FCCI has been fairly understood, mechanical properties remain less studied due to limited reaction volume. Here, through a combining of advanced electron microscopy characterizations and small-scale mechanical testing techniques, including indentation and micro-tensile testing, this study investigated the microscale mechanical properties of FCCI between the ferritic/martensitic (F/M) HT9 cladding and an advanced Uranium (U)-based metallic fuel irradiated at the Advanced Test Reactor to 2.2% FIMA with peak inner cladding temperature reached to 650 °C. Mechanical testing results show significant hardening and embrittlement in the FCCI region. The brittle fracture of FCCI specimen is mainly attributed to the formation of nano-crystallized intermetallic σ-FeCr phase. Whereas mechanical softening was revealed in the unreacted HT9 matrix due to irradiation-induced microstructural and microchemical evolution, specifically, the disappearance of martensitic lath structure and the formation of Fe 2 Mo Laves phase precipitation which consumed the solid solution strengthening Mo from the F/M HT9 matrix. Due to the achieved high cladding temperature, this fuel pin is of particular significance for revealing the high-temperature irradiation effect on the mechanical properties of HT9 cladding. Therefore, the outcomes of this study are expected to contribute to the development of multi-scale mechanical behavior modeling of HT9 cladding for Generation IV reactors which requires cladding to run at higher temperature (above 600 ?).

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Micro-tensile testing of the bond line in hot isostatic pressed aluminum

Considerable effort is being devoted to development and regulatory qualification of low enriched fuels for research and test reactors by many agencies worldwide. One promising fuel configuration being examined for United States higher power research and test reactors (USHPRRs) are plate-type fuels composed of a metallic uranium-molybdenum foil clad in an aluminum alloy. The two pieces of aluminum alloy cladding are bonded using a hot isostatic pressing method. The mechanical properties of the resulting bond line in the aluminum alloy cladding will vary by the HIP'ing parameters, requiring a need to characterize the bond line. Small scale mechanical testing can provide a path for evaluating the mechanical properties and deformation behavior of the bond line both prior to and following irradiation. Here, in this research, room temperature micro-tensile specimens of non-irradiated and irradiated samples containing an Al alloy (AA 6061) bond line were tested to evaluate its strength and deformation behavior. Observations indicated that the strain rate did not affect the deformation behavior or strength and most of the micro-tensile specimens failed in a ductile mode in grains around the bond line. There was no indication that the microstructural features from the bond line affected the mechanical properties of the micro-tensile specimens. An initial examination was performed on irradiated material but further systematic studies of the effects of irradiation can be performed in the future.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

One-loop matrix elements of effective superstring interactions: α' -expanding loop integrands

In the low-energy effective action of string theories, non-abelian gauge interactions and supergravity are augmented by infinite towers of higher-mass-dimension operators. We propose a new method to construct one-loop matrix elements with insertions of operators D 2k F n and D 2k R n in the tree-level effective action of type-I and type-II superstrings. Inspired by ambitwistor string theories, our method is based on forward limits of moduli-space integrals using string tree-level amplitudes with two extra points, expanded in powers of the inverse string tension α'. Similar to one-loop ambitwistor computations, intermediate steps feature non-standard linearized Feynman propagators which eventually recombine to conventional quadratic propagators. With linearized propagators the loop integrand of the matrix elements obey one-loop versions of the monodromy and KLT relations. We express a variety of four- and five-point examples in terms of quadratic propagators and formulate a criterion on the underlying genus-one correlation functions that should make this recombination possible at all orders in α'. The ultraviolet divergences of the one-loop matrix elements are crosschecked against the non-separating degeneration of genus-one integrals in string amplitudes. Conversely, our results can be used as a constructive method to determine degenerations of elliptic multiple zeta values and modular graph forms at arbitrary weight.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Fuel-cladding chemical interaction of a prototype annular U-10Zr fuel with Fe-12Cr ferritic/martensitic HT-9 cladding

As an alternative fuel form, the annular metallic fuel design eliminates the liquid sodium bond between the fuel and the cladding, providing back-end fuel cycle and other benefits. The fuel-cladding chemical interaction (FCCI) of annular fuel also presents new features. In this work, state-of-the-art electron microscopy and spectroscopy techniques were used to study the FCCI of a prototype annular U-10wt%Zr (U-10Zr) fuel with ferritic/martensitic HT-9 cladding irradiated to 3.3% fission per initial heavy atom. Compared with sodium-bonded solid fuels, negligible amounts of lanthanides were found in the FCCI layer in the investigated helium-bonded annular fuel. Instead, most lanthanides were retained in the newly formed UZr 2 phase in the fuel center region. The interdiffusion of iron and uranium resulted in tetragonal ( U ,Zr) 6 Fe phase (space group I4/mcm) and cubic ( U ,Zr)( Fe ,Cr) 2 phase (space group Fd 3 ¯ m). The ( U ,Zr)( Fe ,Cr) 2 phase contains a high density of voids and intergranular uranium monocarbides of NaCl-type crystal structure (space group Fm 3 ¯ m). At the interdiffusion zone and inner cladding interface, a porous lamellar structure composed of alternating Cr-rich layers and U-rich layers was observed. Next to the lamellar region, the unexpected phase transformation from body-centered cubic ferrite (α-Fe) to tetragonal binary Fe-Cr σ phase (space group P4 2 /mnm) occurred, and tetragonal Fe-Cr-U-Si phase (space group I4/mmm) was identified. Due to the diffusion of carbon into the interdiffusion zone, carbon depletion inside the HT-9 led to the disappearance of the martensite lath structure, and intergranular U-rich carbides formed as a result of the diffusion of uranium into the cladding. These detailed new findings reveal the unique features of the FCCI behavior of annular U-Zr fuels, which could be a promising alternative fuel form for high burnup fast reactor applications.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

BCJ amplitude relations for Anti-de Sitter boundary correlators in embedding space

We generalize the color/kinematics duality of flat-space scattering amplitudes to the embedding space formulation of AdS boundary correlators. Kinematic numerators and propagators are replaced with differential operators acting on a scalar contact diagram that is the AdS generalization of the momentum conserving delta function of flat space scattering amplitudes. We show that color/kinematics duality implies differential relations among AdS boundary correlators that naturally generalize the flat space BCJ amplitude relations and verify them for the correlators of Yang-Mills theory and of the Nonlinear Sigma Model through four- and six-points, respectively. For the latter we also find representations of the four- and six-point correlator that manifest the duality. Possible double-copy procedures in AdS space are also discussed.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Next-to-$\mathrm{MHV}$ Yang-Mills kinematic algebra

Kinematic numerators of Yang-Mills scattering amplitudes possess a rich Lie algebraic structure that suggest the existence of a hidden infinite-dimensional kinematic algebra. Explicitly realizing such a kinematic algebra is a longstanding open problem that only has had partial success for simple helicity sectors. In past work, we introduced a framework using tensor currents and fusion rules to generate BCJ numerators of a special subsector of NMHV amplitudes in Yang-Mills theory. Here we enlarge the scope and explicitly realize a kinematic algebra for all NMHV amplitudes. Master numerators are obtained directly from the algebraic rules and through commutators and kinematic Jacobi identities other numerators can be generated. Inspecting the output of the algebra, we conjecture a closed-form expression for the master BCJ numerator up to any multiplicity. We also introduce a new method, based on group algebra of the permutation group, to solve for the generalized gauge freedom of BCJ numerators. It uses the recently introduced binary BCJ relations to provide a complete set of NMHV kinematic numerators that consist of pure gauge.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Post-irradiation examination of legacy high burnup fuel to support safety testing

Safety/transient testing to evaluate performance under off-normal conditions is an essential pillar for both the development of Accident Tolerant Fuels (ATF) and the optimization of fuel operation economics beyond current discharge burnups. Among other factors, the successful interpretation of the transient testing results relies upon the knowledge of the initial conditions of the test, including the characteristics of the fuel system under scrutiny. When testing pre-irradiated material, the assumptions that the fuel and the cladding still have the same properties as in the pre-irradiation stage is obviously wrong and could affect the results of the test. This is particularly true the more burnup accumulates in the fuel rod and irradiation progresses. The knowledge of the initial microstructure of both fuel and cladding allows a clearer interpretation of the subsequent transient testing results, provides validation of the physical phenomena underlying the model predictions and eliminates the uncertainties related to the limited knowledge of the sample status before the test. One example is the phenomenon of fine fragmentation that occurs in Light Water reactor (LWR) fuel. During a Loss of Coolant Accident (LOCA) or Reactivity Initiated Transient (RIA) the fuel can severely fragment. During LOCA, high burnup fuel tend to finely fragment, which has raised safety concerns due to the increased likelihood of dispersal of such small particles once the cladding has burst and due to the increased fission gas release. Therefore, efforts have been devoted to the assessment of a pulverization threshold that could determine the conditions under which fine fragmentation is predominant. However, the lack of information regarding the initial conditions of the fuel, and the connections between those conditions and the pre-transient irradiation history, have hindered the development of a fully mechanistic fragmentation and pulverization criterion. The empirical relationships rely on conservative estimations, due to the lack of information on critical material properties and characteristics. More generally, experimental evidence of the irradiation-induced modifications at microstructural scale are necessary to determine the behavior of the material at the macroscopic scale, with the latter being the one of technological interest. Significant progress has been made in the last two decades in the developments of analytical materials science techniques that can be applied to highly radioactive materials, such as high burnup fuels. The availability of new techniques and the improvement of existing ones has enabled investigations previously not possible that can deepen the understanding of the fuel characteristics and properties at high burnup. The better knowledge of material behavior and irradiation-induced phenomena could help the prediction of its performance. In this context, the scope of the present work is to apply a wide portfolio of advanced characterization techniques to determine properties that are relevant for safety and performance. The results are interpreted in the context of engineering scale post-irradiation examinations and available information on the irradiation conditions.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Structure of the pellet-cladding interaction layer of a high-burnup Zr-Nb-O nuclear fuel cladding

Here, structure of the pellet/cladding-interaction (PCI) layer of a high-burnup nuclear fuel with niobium-bearing cladding was investigated using modern transmission electron microscopy (TEM) techniques. Morphology of the PCI consisted of uniform zirconia layer on the cladding side and finger-like features towards to the ceramic fuel. The PCI layer showed a complex microstructure that constitutes three distinct zirconia layers formed by two zirconia phases. From cladding to fuel, monoclinic, tetragonal, and another tetragonal phase were determined via TEM diffraction patterns and precession electron diffraction (PED) using ASTAR microscopy platform (AMP). Characterizations showed that monoclinic and tetragonal phases close to the cladding were crack-free, but the tetragonal layer adjacent to the fuel contained cracks and pores. Presence of the monoclinic layer suggested that its formation involved the gaseous diffusion of oxygen below threshold dose of fission product damage before the fuel/cladding contact occurred. Furthermore, high-resolution TEM revealed compound phase of (U,Zr)O 2 at fringes of zirconia fingers on the fuel side.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗