Search NASA⌕ Search

Engineering topics

Theingi, San

Publications and source records attributed to Theingi, San.

At least 19 records

Screen-Printed Complex Ag Inks for Si HJT Metallization

Metallization using reactive metal inks has recently attracted significant research interest due to its advantages in cost of materials and manufacturing, while still achieving performance comparable to traditional fire-through particle pastes. Here, we present for the first time the use of reactive silver (Ag) inks via industrial screen-printing and inkjet printing methods for the metallization of different Si surfaces used in tunneling oxide passivating contacts (TOPCon) and Silicon heterojunction (SHJ) solar cells. Printed Ag lines exhibit a conductivity of ~5 Mu O·cm, which is approximately 3 times that of bulk Ag (1.59 µO·cm). The printed metal has a thickness of ~0.5-1.5 Mu m, an order of magnitude smaller than the current fire-through metal finger thickness (~15 Mu m). Contact resistivity measurements of the screen-printed and inkjet-printed samples on a transparent conducting oxide (TCO) surface show a very low value of ~0.2-12 mO·cm 2. Photoluminescence images of the metallized samples demonstrate minimal surface passivation degradation compared to the non-metallized areas (?iVoc <3.5 mV). Scanning electron microscopy images (SEM) reveal the structure of the printed metals on the Si surfaces as porous but much denser than fire-through Ag by nanoparticle paste. In the final presentation, we will showcase our results of printing these reactive Ag inks on high-efficiency heterojunction and TOPCon solar cells with full-area M6 wafers. Additionally, the adhesion of these reactive Ag inks on different Si surfaces according to ASTM D3359-17, as well as the performance of solar cells after standard IEC 61215 freeze/thaw and damp heat tests, will be presented. These new metal inks show promising potential as an alternative to the currently dominant particle-based pastes, offering lower Ag consumption and lower processing temperatures without compromising performance.

heterojunction solar cells↗

Crystalline Si Surface Passivation with Nafion for Bulk Defects Detection with Electron Paramagnetic Resonance

Here, in monocrystalline Si (c-Si) solar cells, identification and mitigation of bulk defects are crucial to achieving a high photoconversion efficiency. To spectroscopically detect defects in the c-Si bulk, it is desirable to passivate the surface defects. Passivation of the c-Si surface with dielectrics such as Al 2 O 3 and SiNx requires deposition at elevated temperatures, which can influence defects in the bulk. Herein, we report on the passivation of different Czochralski (Cz) Si wafer surfaces by an organic copolymer, Nafion. We test the efficacy of the surface passivation at temperatures ranging from 6 to 473 K to detect bulk defects using electron paramagnetic resonance (EPR) spectroscopy. By comparing with state-of-the-art passivation layers, including Al 2 O 3 and liquid HF/HCl, we found that at room temperature, Nafion can provide comparable passivation of n-type Cz Si with an implied open-circuit voltage (iV oc ) of 713 mV and a recombination current prefactor J o of 5 fA/cm 2 . For p-type Cz Si, we obtained an iV oc of 682 mV with a J o of 22.4 fA/cm 2 . Scanning electron microscopy and photoluminescence reveal that Nafion can also be used to passivate the surface of c-Si solar cell fragments scribed from a solar cell module by using a laser. Consistent with previous studies, analysis of the EPR spectroscopy data confirms that the H-terminated surface is necessary, and fixed negative charge in Nafion is responsible for the field-effect passivation. While the surface passivation quality was maintained for almost 24 h, which is sufficient for spectroscopic measurements, the passivation degraded over longer durations, which can be attributed to surface SiO x growth. These results show that Nafion is a promising room-temperature surface passivation technique to study bulk defects in c-Si.

14 SOLAR ENERGY↗

Metal-Complex Inks for Lower Cost and Improved Passivation for Silicon Photovoltaic Metallization

This contribution introduces the silicon PV community to screen-printable metal-complex inks that potentially will reduce Ag usage in Si PV metallization to one-quarter and costs to one-third that of traditional particle-based pastes while also improving passivation. Metal-complex inks are formulated using a Tollen’s reaction to produce inks with a high percentage of diamminesilver (I) cations (22 wt %) in a solution of acetate and formate anions. When printed and dried, labile ammonia ligands evaporate, leaving behind silver cations which, when reduced by formate anions and acetic acid, plate out silver and silver acetate. When annealed to just 300 °C a dense metallic silver film forms with excellent conductivity, and adhesion to silicon. When compared to traditional particle-based screen-printing pastes, the metal-complex inks are much denser, have higher conductivity, use less Ag, and are a fraction of the cost. Importantly, the inks anneal from 90 – 450 °C allowing for improved passivation schemes compared with fired SiNx. This contribution highlights first experiments on the improved passivation of metallized poly-Si/SiO2 passivated contacts using metal-complex Ag inks.

Young, David L. (ORCID:0000000340970493)↗

Self-Assembled Monolayer Patterning for PolySi/SiO2 Passivated Contacts

We utilize hexamethyldisilazane (HMDS) based self assembled monolayers to pattern polysilicon (polySi) passivated contacts. We find process conditions that allow for etching front side n/polySi between fingers; thereby increasing Jsc. Importantly, the Voc does not degrade indicating the additional process steps do not introduce defects or impurities. HMDS layers remain on the surface for metallization without detriment to transport.

degradation↗

Loss Analysis and Performance Optimization Pathways of 729-mV Voc Si Solar Cells with Poly-Si on Locally-Etched Dielectric Passivating Contacts

In this article, the loss analysis of silicon solar cells with polysilicon on locally-etched dielectric passivating contacts with Voc=729.0 mV and efficiency=22.6% has been presented. Experimentally, nano-pinholes were introduced in SiO x (2.2 nm) and SiO x /SiN y (2.2 nm/8nm) stack using metal-assisted chemical etching (MACE). SunSolve and Quokka3 were used to simulate the experimental solar cell and investigate the optical and electrical power losses. Simulations suggest maximum power loss occurs due to recombination and resistive losses in the bulk (~0.76 mW/cm2) followed by power loss due to rear contact recombination (~0.35 mW/cm2). Recombination at the front surface also contributes to 0.24 mW/cm2. The effect of improving the bulk lifetime and lowering the recombination current density at the rear side on Voc, FF and hence, efficiency has been investigated. Further, advanced structures have been proposed to minimize recombination and parasitic absorption to achieve higher Voc and Jsc of the solar cells with locally-etched dielectric passivating contacts.

contacts↗

Patterned nanochannel sacrificial layer for semiconductor substrate reuse

Described herein are systems and methods of utilizing nanochannels generated in the sacrificial layer of a semiconductor substrate to increase epitaxial lift-off speeds and facilitate reusability of GaAs substrates. The provided systems and methods may utilize unique nanochannel geometries to increase the surface area exposed to the etchant and further decrease etch times.

Mangum, John Stanley↗

Defect Characterization of Monocrystalline Silicon Solar Cells with Polysilicon Passivated Contact Using Electrically-Detected Magnetic Resonance (EDMR) Spectroscopy

As the c-Si based solar cell efficiencies are approaching over 26%, it is becoming critical to characterize the low concentrations of the defects – as low as 10^10-10^11 cm-3 (for e.g., iron contamination in high-lifetime Ga-doped wafers3 and n-type wafers), and further reduce them. Also, atomistic level understanding of the mechanisms of the low concentration process-induced-defects and reliability limiting defects (such as light and elevated temperature induced degradation, surface passivation degradation) is needed to design the mitigation strategies. The conventional characterization techniques are limited due to their detection limitations. Some of the techniques based on lifetime spectroscopies can still be used for low concentration characterization however, they are based on estimations and theoretical models and hence, indirect and cannot fully reveal information about the microscopic mechanism of the defects. Thus, we present the application of an ultrasensitive magnetic resonance-based technique for the direct spectroscopic detection of the defects in Si PV - electrically detected magnetic resonance (EDMR). In this work, we aim to focus on establishing a process flow for fabrication of minicells with (miniature replica of the larger-area cells) and setting up the routine for EDMR measurements on them with the EDMR instrumentation capability at NREL. For the EDMR measurements, sample size is limited by the dimensions of sample holder tube (width less than 3.2 mm, active area - 20 mm). Thus, we have designed c-Si based minicells with polysilicon (poly-Si) passivated contacts same as the larger-area cells that we fabricate in our group at NREL. We also modified our minicell process flow for fabricating the textured minicells for preserving the texture during processing and taking care of the laser-ablation edge damage which can significantly affect the performance of such small devices. We have achieved comparable performance on these newly fabricated minicells as that of our 4 cm2 devices with same structure (comparable VOC, JSC, FF). We also conducted EDMR measurements on the minicells and observed a distinct EDMR signal at g-value ~2.005 at temperatures 30K and above, as shown in Fig. 2. We associate this signal to the presence of silicon dangling bonds based on the g-value. We also observed an EDMR signal at g-value ~1.998 at temperature ~5K. The origin of this signal is still being investigated. Thus, we show the proof of concept of minicells and EDMR measurements with which we now aim to study some of the unknown defects in silicon solar cell devices.

EDMR↗

Self-Assembled Monolayer Procedure to Pattern Silicon Passivated Contacts

We utilize hexamethyldisilazane (HMDS)-based self-assembled monolayers to pattern polysilicon (polySi) passivated contacts. We find process conditions that allow for etching frontside n/polySi between fingers, thereby increasing Jsc. Importantly, the Voc does not degrade indicating the additional process steps do not introduce defects or impurities. HMDS layers remain on the surface for metallization without detriment to transport.

hexamethyldisilazane↗

Loss Analysis and Performance Optimization Pathways of 729-mV VocSi Solar Cells with Poly-Si on Locally-Etched Dielectric Passivating Contacts

In this article, the performance analysis of a 22.5% efficient polysilicon on silicon oxide (poly-Si/SiOx) passivated contact solar cells with deliberately introduced pinholes using metal-assisted chemical etching (MACE) has been performed with the help of optical analysis using Sunsolve and electrical analysis using Quokka3. The power loss is maximum due to recombination and resistive losses in the bulk (~0.76 mW/cm2 ) followed by power loss due to rear contact recombination (~0.35 mW/cm2 ). Recombination at the front surface also contributes to 0.24 mW/cm2. The effect of improving the bulk lifetime and lowering the recombination current density at the rear side on Voc, FF and efficiency has been investigated.

MACE↗

Self Assembled Monolayers for Passivated Contacts

Passivated contacts mitigate defects typically encountered due metallization of solar cells. We deposit amorphous silicon (a-Si:H) on an oxidized silicon wafer via PECVD and anneal at high temperature to crystallize into polysilicon passivated contact. One drawback is the absorption of the polysilicon between grid fingers, so removal of this material is desirable to maximize Jsc. Alternatively, interdigitated back contact cells rely on a gap between n- and p- fingers, which is commonly etched to ensure electronic isolation. We utilize a self assembled monolayer (SAM) using hexamethyldisilazane (HMDS) as a precursor to pattern and etch amorphous silicon (a-Si:H) and polysilicon without the need for photoresist. Ultraviolet light exposure oxidizes the HMDS by photocleaving the organic groups [1] of the SAM leaving a patterned SiO2. Directly soaking this in TMAH will eventually etch the SAM and the silicon, where the SiO2 serves as an etch mask. Inversely, a dilute HF dip selectively etches this SiO2 and the SAM remains. A subsequent soak in TMAH selectively etches the underlying silicon, where the SAM serves as an etch mask. Importantly, we find that the SAM can remain intact for metallization, where we measure 10 mO-cm2 specific contact resistivity on n-type polysilicon.

passivation↗

Electrical Analysis of Pulsed Laser Annealed Poly-Si: Ga/SiOx Passivating Contacts

In this contribution, we examine Ga hyper-doped poly-Si/SiOx contacts realized by pulsed laser melting (PLM). Here, we use Ga as a novel p-type dopant and B as a conventional dopant to induce non-equilibrium doping using an excimer laser. We perform simulations to visualize the maximum melt depth profiles within the poly-Si, with a goal of distributing dopants close to the tunneling oxide, but at the same time preserving the passivation. Hall measurements show that sheet resistance for B is lower than Ga due to its higher solid solubility limit in Si. After comparing the Hall active dopant concentration with the chemical concentration obtained by SIMS measurement, we show nearly 100% activation B activation reaching 10^21 cm-3, while only ~20% activation for Ga. Nevertheless, we achieve active doping concentrations of Ga in poly-Si six times higher than its solid solubility limit in Si (~10^19 cm-3). We compare our Hall mobilities with values in the literature for c-Si and show that B mobilities in laser-treated poly-Si are close to that of the literature value for B, while Ga mobilities are lower, possibly due to additional scattering channels within grain boundaries and deformed lattice. We also compare our results on PLM samples with conventional furnace annealed samples, and we show much higher percent activation and mobilities. Previously, we showed a low contact resistivity of 35.5 +/- 2.4 m..omega..cm2. Here, we further confirm this result by scanning spreading resistance microscopy and Kelvin force nanoprobe microscopy. We demonstrate that our poly-Si: Ga/nCz contact exhibits large drift and diffusion currents under normal cell operating voltage, which widens the laser processing window for a good metal/poly-Si/c-Si contact.

high-efficiency solar cells↗

Metal-Complex Inks for Lower Cost and Improved Passivation for Silicon Photovoltaic Metallization

This contribution introduces the silicon PV community to screen-printable metal-complex inks that potentially will reduce Ag usage in Si PV metallization to one-quarter and costs to one-third that of traditional particle-based pastes while also improving passivation. Metal-complex inks are formulated using a Tollen's reaction to produce inks with a high percentage of diamminesilver (I) cations (22 wt %) in a solution of acetate and formate anions. When printed and dried labile ammonia ligands evaporate, leaving behind silver cations which, when reduced by formate anions and acetic acid, plate out silver and silver acetate. When annealed to just 300 degrees C a dense metallic silver film forms with excellent conductivity, and adhesion to silicon. When compared to traditional particle-based screen-printing pastes, the metal-complex inks are much denser, have higher conductivity, use less Ag, and are a fraction of the cost. Importantly, the inks anneal from 90 - 450 degrees C allowing for better passivation schemes than fired SiNx. This contribution highlights first experiments on the improved passivation of metallized poly-Si/SiO2 passivated contacts using metal-complex, Ag inks compared with particle-based, fired pastes.

metal-complex ink↗

High-voltage monocrystalline Si photovoltaic minimodules based on poly -Si/SiO x passivating contacts for high-power laser power conversion

By using photovoltaic cells under high-intensity laser illumination, much higher photoconversion efficiencies are obtained than under the solar spectrum. Here we demonstrate a monocrystalline Si based minimodule to convert laser light into electricity using edge-illuminated Si "minicells" based on polysilicon on silicon oxide passivating contacts. Ten fully metallized devices were stacked in series and illuminated from the edge, creating a high-voltage, low-current minimodule that mitigates resistive and Auger-Meitner losses. The minimodule shows a high open-circuit voltage of >5 V when tested under 1-Sun illumination and >7 V at higher illumination intensities when tested with a flash simulator. The fill factor in these minimodules is limited by shunting at low illuminations but reaches a maximum of ~78% for higher illumination intensities >40 Suns (current density >1200 mA/cm 2 ), indicating that the minimodules are not limited by series resistance up to 40 Suns. Under 1000 nm monochromatic light, we measure efficiencies >40% at > 40 Suns equivalent illumination, showing the potential of passivated contact Si cells for laser power conversion.

14 SOLAR ENERGY↗

Mitigation of shunt in poly -Si/SiO$_{x}$ passivated interdigitated back contact monocrystalline Si solar cells by self-aligned etching between doped fingers

Polycrystalline silicon on silicon oxide (poly-Si/SiO x ) passivating contacts can be used for ultra-high-efficiency interdigitated back contact (IBC) monocrystalline silicon solar cells. We evaluate the use of intrinsic poly-Si for the region that isolates the p- and n-type fingers at the back side of IBC devices. To mitigate shunt across the isolation region between the doped p- and n-type fingers, we demonstrate self-aligned subtractive processing by etching the poly-Si in the isolation region using SF6 plasma followed by etching in a tetramethylammonium hydroxide (TMAH) solution. After removal of the poly-Si, the isolation region was passivated with SiN x and Al 2 O 3 , which resulted in an 11.7% increase in the fill factor in a 19.8% efficient device. Furthermore, we evaluate the limitations of this device through Suns-V oc analysis and simulations using SunSolve and Quokka3 solar cell simulation software. Through Quokka3, we show that the most significant efficiency losses come from junction recombination current (J 02 ) in the isolation region between doped fingers. We predict that the cell efficiency can be most improved with reduced J 02 through better isolation of heavily doped fingers by etching the isolation region deeper into the bulk or through enhanced surface chemical passivation in this region.

14 SOLAR ENERGY↗

Pulsed Laser Annealed Ga Hyperdoped Poly‐Si / SiO x Passivating Contacts for High‐Efficiency Monocrystalline Si Solar Cells

Polycrystalline Si ( poly ‐Si)‐based passivating contacts are promising candidates for high‐efficiency crystalline Si solar cells. We show that nanosecond‐scale pulsed laser melting (PLM) is an industrially viable technique to fabricate such contacts with precisely controlled dopant concentration profiles that exceed the solid solubility limit. We demonstrate that conventionally doped, hole‐selective poly ‐Si/SiO x contacts that provide poor surface passivation of c ‐Si can be replaced with Ga‐ or B‐doped contacts based on non‐equilibrium doping. We overcome the solid solubility limit for both dopants in poly ‐Si by rapid cooling and recrystallization over a timescale of ∼25 ns. We show an active Ga dopant concentration of ∼3 × 10 20 cm −3 in poly ‐Si which is six times higher than its solubility limit in c ‐Si, and a B dopant concentration as high as ∼10 21 cm −3 . We measure an implied open‐circuit voltage of 735 mV for Ga‐doped poly ‐Si/SiO x contacts on Czochralski Si with a low contact resistivity of 35.5 ± 2.4 mΩ cm 2 . Scanning spreading resistance microscopy and Kelvin probe force microscopy show large diffusion and drift current in the p ‐ n junction that contributes to the low contact resistivity. Our results suggest that PLM can be extended for hyperdoping of other semiconductors with low solubility atoms to enable high‐efficiency devices.

14 SOLAR ENERGY↗

Electrical Analysis of Pulsed Laser Annealed Poly-Si:Ga/SiOx Passivating Contacts

High-efficiency single crystalline silicon (c-Si) solar cells require precise control of dopant diffusion profiles and highly active doping concentrations through thermal annealing. Conventional furnace annealing has been successfully employed for dopant diffusion in aluminum back-surface field (Al-BSF), passivated emitter and rear contact (PERC), and Topcon cells. However, furnace annealing limits some next-generation polycrystalline silicon (poly-Si) on SiOx passivating contacts. This limitation largely affects p-type passivating contacts by not being able to: 1) control the dopant diffusion accurately to prevent B segregation at the SiOx and c-Si interface; and 2) provide highly activated doping concentrations for low contact resistivity. In this contribution, we use a nanosecond excimer laser to examine the passivation quality and electrical performance of both B- and Ga-doped poly-Si/SiOx passivating contacts. The core of this method is to take advantage of the nonequilibrium nature of the anneal through rapid melting and recrystallizing the poly-Si in a short timescale and to achieve doping concentrations above the solid solubility limit. Simulations were performed on polished surfaces to visualize the doping diffusion profiles under different laser conditions, and secondary ion mass spectrometry (SIMS) was used to verify the experimental diffusion profiles post pulsed laser melting (PLM). The results show the dopant diffusion profiles can be tuned precisely through PLM. The electrical analysis using VdP-Hall measurements reveals that the active doping concentration reached 10^21 cm-3 for B and ~2×10^21 cm-3 for Ga in poly-Si, far exceeding their solid solubility limit in Si, with a nearly 100% dopant activation achieved for B, and 20% for Ga. This highly activated dopant profile results in a low contact resistivity of <15 mO·cm^2 for B-doped contacts and <40 mO·cm^2 for Ga-doped contacts. We demonstrate that the passivation quality of the laser annealed contacts shows a linear dependency with the laser energy density and the number of pulses. PLM was also performed on random pyramid textured samples, and we found that preferential melting exists for the tips of pyramids, which can be pursued further for selective pinhole opening. Additionally, we perform thermal stability tests of these hyperdoped passivating contacts and show that under certain laser conditions, the B-doped samples exhibit good thermal stability with near full activation for temperatures up to 800°C. Lastly, we transfer this technique to a larger area by overlapping laser spots and show uniform passivation quality and electrical performance. We are currently implementing this PLM annealed p-type passivating contacts into double-side back-junction poly-Si/SiOx passivating contact devices. Our results show that PLM can not only enable the next generation of high-efficiency c-Si photovoltaics technology but can also benefit the c-Si integrated circuit industry through hyperdoping other semiconductors with atoms that may otherwise have a low solubility.

doping diffusion profile↗

Nafion Passivation of c-Si Surface and Edge for Electron Paramagnetic Resonance

Effective surface passivation of crystalline silicon (c-Si) surface by reducing the carrier recombination rate has led to modern c-Si solar cells with efficiencies > 25% in both laboratory and industrial settings. Typical mainstream surface passivation techniques include high-temperature silicon oxide (SiOx), amorphous silicon (a-Si:H), hydrogen-rich silicon nitride (SiNx), and aluminum oxide (Al2O3) [1]. They have demonstrated excellent surface recombination velocity of < 1 cm/s owing to both chemical passivation (via the hydrogen saturation of Si dangling bonds at the c-Si surface), and field-effect passivation (via the band bending from the fixed charge of the dielectric layers). Recently, several groups have studied solution-based organic materials for c-Si passivation, including bis(trifluoromethane)sulfonimide (TFSI), polystyrenesulfonate, and Nafion [2, 3] via spin or dip coating. All films were processed at ambient room temperature, and a high lifetime of 12 ms, as well as a low saturation current density (J0) of 16 fA/cm2, have been demonstrated using Nafion passivation [2]. However, despite the air instability, Nafion has several advantages when introduced to PV applications: (a) Wafer quality can be measured at high throughput after several process stages. (b) It is compatible with PL mapping, compared to HF liquid passivation which cannot be performed in room ambient. (c) Nafion process is fast and poses fewer constraints on process complexity, and cleanness, compared to Al2O3 and a-Si:H passivation. (d) Nafion is the ideal room temperature passivation, which can be applied onto a small fragment of a degraded module to investigate microscopic mechanisms when studying degradation mechanisms. Edge passivation is needed for advanced characterization tests such as Electron Paramagnetic Resonance (EPR), Electrically Detected Magnetic Resonance (EDMR), Deep Level Transient Spectroscopy (DLTS), local cell current-voltage (J-V), and Suns-Voc. In such cases, the laser-damaged minicell edges will obscure the true degradation mechanisms, and Nafion can effectively passivate them without causing further degradation through elevated-temperature processes. In this contribution, we show the passivation results of Nafion on bare nCz and compare it with a Al2O3 witness. We highlight the importance of edge pre-treatment before Nafion to achieve good passivation. We show that Nafion can reach decent passivation without undergoing high-temperature processes. We also explore the temperature dependency of Nafion through photoluminescence (PL) study and demonstrate the application of Nafion under cryogenic temperature (~6 K) through EPR. Our results reveal that Nafion can reduce surface and edge Si dangling bonds at low temperatures. Thus, it can be used as an effective room temperature passivation technique for advanced characterization methods.

c-Si↗