SEARCH · Search NASA

Results for “Test program”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23

All sources NASA NTRS DOE OSTI

NASA NTRS1985

Hardware test program for evaluation of baseline range-range rate sensor concept

The baseline range/range rate sensor concept was evaluated. The Interrupted CW (ICW) mode of operation continued with emphasis on establishing the sensitivity of the video portion of the receiver was 7 dB less than the theoretical value. This departs from test results of previous implementations in which achieved sensitivity was within 1.5 to 2 dB of the theoretical value. Several potential causes of this discrepancy in performance were identified and are scheduled for further investigation. Results indicate that a cost savings in both per unit and program costs are realizable by eliminating one of the modes of operation. An acquisition (total program) cost savings of approximately 10% is projected by eliminating the CW mode of operation. The modified R/R sensor would operate in the ICW mode only and would provide coverage from initial acquisition at 12 nmi to within a few hundred feet of the OMV. If the ICW mode only were selected, then an accompanying sensor would be required to provide coverage from a few hundred feet to docking.

Source record↗

NASA NTRS1999

High-Lift Engine Aeroacoustics Technology (HEAT) Test Program Overview

The NASA High-Speed Research program developed the High-Lift Engine Aeroacoustics Technology (HEAT) program to demonstrate satisfactory interaction between the jet noise suppressor and high-lift system of a High-Speed Civil Transport (HSCT) configuration at takeoff, climb, approach and landing conditions. One scheme for reducing jet exhaust noise generated by an HSCT is the use of a mixer-ejector system which would entrain large quantities of ambient air into the nozzle exhaust flow through secondary inlets in order to cool and slow the jet exhaust before it exits the nozzle. The effectiveness of such a noise suppression device must be evaluated in the presence of an HSCT wing high-lift system before definitive assessments can be made concerning its acoustic performance. In addition, these noise suppressors must provide the required acoustic attenuation while not degrading the thrust efficiency of the propulsion system or the aerodynamic performance of the high-lift devices on the wing. Therefore, the main objective of the HEAT program is to demonstrate these technologies and understand their interactions on a large-scale HSCT model. The HEAT program is a collaborative effort between NASA-Ames, Boeing Commercial Airplane Group, Douglas Aircraft Corp., Lockheed-Georgia, General Electric and NASA - Lewis. The suppressor nozzles used in the tests were Generation 1 2-D mixer-ejector nozzles made by General Electric. The model used was a 13.5%-scale semi-span model of a Boeing Reference H configuration.

Zuniga, Fanny A.↗

NASA NTRS1986

X-29 Flight Test Program including wind tunnel and computational support

A cooperative effort has been defined between NASA-Ames/Dryden Flight Research Facility and NASA-Langley Research Center in support of the X-29A Advanced Technology Demonstrator. The effort involves three phases: flight testing, wind-tunnel testing in the National Transonic Facility, and computational support of each experimental phase. These efforts are primarily aimed at understanding the complex flow phenomena and component interactions associated with the X-29A. Each phase of the effort is discussed in detail and initial data comparisons are presented. In summary, the synergistics effects of the complementary phases are identified, which will enhance the understanding of the unique aerodynamics of the X-29A.

Waggoner, E. G.↗

NASA NTRS1993

Techniques for improving the accuracy of cyrogenic temperature measurement in ground test programs

The performance of a sensor is often evaluated by determining to what degree of accuracy a measurement can be made using this sensor. The absolute accuracy of a sensor is an important parameter considered when choosing the type of sensor to use in research experiments. Tests were performed to improve the accuracy of cryogenic temperature measurements by calibration of the temperature sensors when installed in their experimental operating environment. The calibration information was then used to correct for temperature sensor measurement errors by adjusting the data acquisition system software. This paper describes a method to improve the accuracy of cryogenic temperature measurements using corrections in the data acquisition system software such that the uncertainty of an individual temperature sensor is improved from plus or minus 0.90 deg R to plus or minus 0.20 deg R over a specified range.

Dempsey, Paula J.↗

NASA NTRS1993

Techniques for improving the accuracy of cryogenic temperature measurement in ground test programs

Dempsey, Paula J.↗

NASA NTRS1977

Air Force nickel-hydrogen test program

After using all the instrumentation that is available on a nickel hydrogen battery it will be subjected to the same low earth orbit cycles experienced by the sixty amphere hour nickel cadmium batteries now being flown on some low earth orbit missions. The objective of the test is to demonstrate real differences between the two batteries. In order to simulate flight conditions, the thermal environment and criteria for charge control will vary. The depth of discharge will be increased and testing will continue until some failures or some degradation or spread between cell performances are revealed. Different charge control modes are being considered in order to demonstrate a reasonable life for the nickel hydrogen battery.

Gandel, M. G.↗

NASA NTRS1991

Pressure vessel burst test program. II

The current status is disucssed of a program to study the characteristics of blast waves and fragmentation generated by ruptured gas-filled pressure vessels. Current methods for assessing vessel safety and burst parameters are briefly reviewed, and pneumatic burst testing operations and testing results are examined. A comparison is made with current methods for burst assessment. It is tentatively concluded that, at close distances, vessel burst overpressures are less than those of high-explosive (HE) blasts with equivalent energy and are greater than HE far from the vessel. The impulse appears to be the same for both vessel bursts and equivalent energy HE blasts. The functional relationship between shock velocity and overpressure ratio appears to be the same for vessel bursts as for HE blasts. The initial shock overpressure appears to be much less than vessel pressure and may be found using the one-dimensional shock tube equation.

Cain, Maurice R.↗

NASA NTRS1983

Ascent air data system results from the space shuttle flight test program

The ascent air data system of the Space Shuttle consists of a simple biconic spike probe on the nose of the external tank. Pressure measurements were calibrated in a wind tunnel to obtain vehicle attitude and speed (relative to the air) and dynamic pressure. The wind tunnel test data analysis and the calibration are discussed in terms of test problems and calibration parameter formulation. The flight pressures are traced from telemetry data to final air data products. Analysis of the flight results showed that static pressure could not be accurately determined at the higher Mach numbers (above approx. 2.0). By replacing static pressure with data from a postflight estimated trajectory the ascent air data system performance met the user requirements. Lessons learned are enumerated, the most important being the need for a thorough systems integration effort.

Hillje, E. R.↗

NASA NTRS1986

Test program to provide confidence in liquid oxygen cooling of hydrocarbon fueled rocket thrust chambers

An experimental program has been planned at the NASA Lewis Research Center to build confidence in the feasibility of liquid oxygen cooling for hydrocarbon fueled rocket engines. Although liquid oxygen cooling has previously been incorporated in test hardware, more runtime is necessary to gain confidence in this concept. In the previous tests, small oxygen leaks developed at the throat of the thrust chamber and film cooled the hot-gas side of the chamber wall without resulting in catastrophic failure. However, more testing is necessary to demonstrate that a catastrophic failure would not occur if cracks developed further upstream between the injector and the throat, where the boundary layer has not been established. Since under normal conditions cracks are expected to form in the throat region of the thrust chamber, cracks must be initiated artificially in order to control their location. Several methods of crack initiation are discussed in this report. Four thrust chambers, three with cracks and one without, should be tested. The axial location of the cracks should be varied parametrically. Each chamber should be instrumented to determine the effects of the cracks, as well as the overall performance and durability of the chambers.

Armstrong, E. S.↗

NASA NTRS1979

Diode step stress testing program for JANTX1N3031B

The effect of power/temperature step stress when applied to the zener diode JANTX1N3031B manufactured by Siemens and Motorola is reported. A total of 48 samples from each manufacturer was submitted to the process. In addition, two control sample units were maintained for verification of the electrical parametric testing.

Source record↗

NASA NTRS1979

Transistor step stress testing program for JANTX2N2369A

The effect is reported of power/temperature step stress when applied to the transistor JANTX2N2369A manufactured by Raytheon and National Semiconductor. A total of 48 samples from each manufacturer was submitted to the process. In addition, two control sample units were maintained for verification of the electrical parametric testing. The power/thermal stress tests are described, and failure analyses are presented.

Source record↗

NASA NTRS1994

Program test objectives milestone 3

The following conclusions have been developed relative to propulsion system technology adequacy for efficient development and operation of recoverable and expendable launch vehicles (RLV and ELV) and the benefits which the integrated propulsion technology demonstrator will provide for enhancing technology: (1) Technology improvements relative to propulsion system design and operation can reduce program cost. Many features or improvement needs to enhance operability, reduce cost, and improve payload are identified. (2) The Integrated Propulsion Technology Demonstrator (IPTD) Program provides a means of resolving the majority of issues associated with improvement needs. (3) The IPTD will evaluate complex integration of vehicle and facility functions in fluid management and propulsion control systems, and provides an environment for validating improved mechanical and electrical components. (4) The IPTD provides a mechanism for investigating operational issues focusing on reducing manpower and time to perform various functions at the launch site. These efforts include model development, collection of data to validate subject models, and ultimate development of complex time line models. (5) The IPTD provides an engine test bed for tri/bi-propellant engine development firings which is representative of the actual vehicle environment. (6) The IPTD provides for only a limited multiengine configuration integration environment for RLV. Multiengine efforts may be simulated for a number of subsystems and a number of subsystems are relatively independent of the multiengine influences.

Gaynor, T. L.↗

NASA NTRS1979

Transistor step stress testing program for JANTX2N2905A

The effect of power/temperature step stress when applied to the transistor JANTX2N2905A manufactured by Texas Instruments and Motorola is reported. A total of 48 samples from each manufacturer was submitted to the process outlined. In addition, two control sample units were maintained for verification of the electrical parametric testing. All test samples were subjected to the electrical tests outlined in Table 2 after completing the prior power/temperature step stress point.

Source record↗

NASA NTRS1979

Transistor step stress testing program for JANTX2N4856

The effect of power/temperature step stress when applied to a field effect transistor JANTX2N4856 manufactured by Texas Instruments and Teledyne was evaluated. A total of 48 samples from each manufacturer was submitted to the process. In addition, two control units were maintained for verification of the electrical parametric testing.

Source record↗

NASA NTRS1979

Diode step stress testing program for JANTX1N2989B

The effect of power/temperature step stress when applied to the zener diode JANTX2N2989 manufactured by Siemens and General Semiconductor is reported. A total of 48 samples from each manufacturer was submitted to the process. In addition, two control sample units were maintained for verification of the electrical parameteric testing.

Source record↗

NASA NTRS1979

Diode step stress testing program for JANTX1N5618

The effect of power/temperature step stress when applied to the switching diode JANTX1N5618 manufactured by Semtech and Micro Semiconductor is reported. A total of 48 samples from each manufacturer was submitted to the process. In addition, two control sample units were maintained for verification of the electrical parametric testing.

Source record↗

NASA NTRS1947

Data Obtained in the Flight Measurements to Determine the Stability and Control Characteristics of a C-54D Airplane (AAF No. 42-72713) and a Summary of the Test Program

The flight investigation of the C-54D airplane was initiated to determine the necessity of changes or additions to existing handling-qualities requirements to cove the case of instrument approaches with large airplanes. This paper gives a brief synopsis of the results and presents the measured data of tests to determine the stability and control characteristics. It was found that no new requirements were necessary to cover the problems of instrument approaches. The C-54D airplane tested met the Amy and Navy stability and control requirements except for the following items. The control-system friction with autopilot installed vas double that allowed by the requirements. The amount of friction was found to impair the controllability of the airplane in precision flying. The lateral and directional characteristics were good except that the maximum pb/2V was slightly below the minimum required, and the elevator-control forces to obtain the maximum pb/2V at low speeds were above the Army and Navy requirements. The longitudinal stability and control characteristics were good except that the elevator-control forces exceeded the limits of the Army and Navy requirements in turns and in landings. The stalling characteristics were considered good in all conditions with the stall warning in the form of tail buffeting occurring at speeds approximately 5 miles per hour above the stall.

Talmage, Donald B.↗

NASA NTRS1979

Diode step stress testing program for JANTX1N3016B

The effect of power/temperature step stress when applied to a variety the zener diode JANTX2N3016B manufactured by Siemens and Motorola is reported. A total of 48 samples from each manufacturer was submitted to the process. In addition, two control sample units were maintained for verification of the electrical parametric testing.

Source record↗