Search NASA⌕ Search

SEARCH · Search NASA

Results for “Powder Bed Fusion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

A transport-based framework for solidification cracking in Ni-based superalloys processed by laser powder bed fusion

Solidification cracking remains a persistent barrier to laser powder bed fusion (LPBF) processing of solid-solution-strengthened (SSS) Ni-based superalloys and is commonly attributed to carbide formation, liquation-type failure, or elemental segregation. In this work, the cracking behavior of three SSS Ni-based superalloys—Inconel 625 (625), Inconel 617 (617), and Haynes 230 (230)—is examined under comparable LPBF conditions to evaluate the origins of their cracking susceptibility. Carbides were present in both 625 and 230, yet cracking behavior differed significantly. MC-type carbides in 625 remain discrete and preserve liquid connectivity, whereas Cr-rich M23C6 carbides in 230 form at cellular triple junctions that bottleneck the interdendritic liquid network, influencing cracking through liquid connectivity rather than as an independent cause. Alloy 617 exhibited anomalous segregation without resolvable secondary phases yet cracked mildly, indicating that extensive carbide formation is not a prerequisite for cracking. To rationalize these observations, a transport-limited framework is proposed in which cracking occurs when terminal-liquid feeding cannot accommodate solidification-induced strain; among the mechanisms evaluated, this framework is most consistent with the physical constraints imposed by LPBF solidification. Transport-based crack-susceptibility indexes incorporating permeability, viscosity, and solidification kinetics distinguish the alloy hierarchy; permeability ratios Krat increased from approximately 7 (625) to 11.5 (617) and 14.5 (230), with corresponding increases in the μ-weighted mushy zone risk index (CSIMZRM). These results are consistent with transport-limited liquid feeding as a rate-limiting contributor to solidification cracking in LPBF-processed SSS Ni-based superalloys, providing a physically grounded basis for alloy and process design.

Hyer, Holden [ORNL] (ORCID:0000000343915561)↗
DOE OSTI2025

Laser Powder Bed Fusion Microstructure Surrogate Model

SAND2025-11467O The Laser Powder Bed Fusion (LPBF) Microstructure Surrogate Model is a machine-learning-based tool. It predicts statistics of microstructures that are produced by the LPBF additive manufacturing process. It includes a series of codes for training, testing, and analyzing the model as well as utility scripts for handling data. Sandia National Laboratories is a multimission laboratory managed and operated by National Technology & Engineering Solutions of Sandia, LLC, a wholly owned subsidiary of Honeywell International Inc., for the U.S. Department of Energy’s National Nuclear Security Administration under contract DE-NA0003525.

Moser, Daniel [Sandia National Lab. (SNL-CA), Live↗
DOE OSTI2024

Gas pore correlations in laser powder bed fusion of Al6061

Additive manufacturing (AM) of metal materials based on powder bed fusion technology is widely used now in many industries. A known limitation of this type of manufacturing is the formation of gas pores in the bulk material. Here we present a combined X-ray imaging and mid-infrared pyrometry study of pore formation in side-by-side tracks of Al6061 for different processing conditions using both in-situ and post-processing analysis. By carefully quantifying the distributions and correlations of pore positions, we show that an existing pore in one track often catalyzes the formation of another pore in an adjacent track. In a raster scan strategy commonly used to construct bulk material, this phenomenon has the result of forming subsurface perforations, or lines of pores transverse to the scanning direction in a rastered patch. If controlled, this effect can be eliminated to improve the yield strength of the build, or exploited to create programmable failures for specific purposes.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Effect of threshold parameters on infrared segmentation methods for porosity detection in electron beam powder bed fusion

In-situ process monitoring has seen significant interest in additive manufacturing to address qualification and certification goals. This is especially prevalent in metal powder bed fusion processes such as electron beam powder bed fusion (PBF-EB), with layer-wise infrared imaging being commonly used to detect defects. Here, this work compares two different segmentation methods (static thresholding and statistical thresholding) used for detecting porosity from in-situ infrared imaging data for PBF-EB. Samples were manufactured at a variety of focus offset values to induce porosity. Then, the segmented infrared images were compared to ex-situ X-ray computed tomography scans, which served as a ground-truth reference for objective evaluation. Through this analysis framework, the influential parameters, static threshold and N-value (number of standard deviations above the mean pixel value), respectively, for both image segmentation methods were analyzed and compared for their effects on porosity detection. With optimal parameter settings, the two methods had similar porosity detection performance, but the statistical method performed better under a larger variety of parameter settings.

Infrared imaging↗
DOE OSTI2025

A detailed study of pre-heating effects in electron beam melting powder bed fusion process

Metal-based additive manufacturing processes, such as powder bed fusion with electron beam (PBF-EB) process, also referred to as electron beam melting (EBM), can produce high-density parts with minimal residual stresses due to the uniform and coherent preheating of the powder bed. However, understanding and controlling the multiple stages of preheating is required to enable the production of high-quality, consistent parts of various materials. This work presents a large-scale, multi-layer, three-dimensional numerical analysis focused on studying the preheating stages for predicting thermal history during the PBF-EB process. The model follows a continuous multi-stage cyclic process, that incorporates all the main stages of the PBF-EB process for 316 L stainless steel. This includes the gradual deposition of a new powder layer, the first and second preheating levels of the powder bed, and the energy deposition during melting (excluding the actual melt-pool behavior simulation). The model employs an adaptive time-scaling approach that automatically adjusts the energy deposition for each solution time-increment. This allows for localized changes in time-resolution over an otherwise computationally expensive multi-layer procedure. The material property variations are also taken into account, with an emphasis on the subtle irreversible changes in powder effective thermal conductivity after the two requisite preheating stages of the powder bed. This effect is studied using simplified conductivity models from the literature for partially sintered powder, validated by a dedicated experiment and numerical simulation. The large-scale model is then used to estimate the actual temperatures during first and second preheating levels for 316 L steel, which is not yet fully supported commercially for PBF-EB. Model predictions are corroborated by experiments, using and analyzing IR images, taken at the completion of each layer by the machine’s built-in infrared camera. The current model also incorporates a qualitative assessment for the effects of conductivity change during pre-heating, as well as evaluates the applicability of the time-scaling approach.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Sub-millisecond keyhole pore detection in laser powder bed fusion using sound and light sensors and machine learning

Laser powder bed fusion is a mainstream additive manufacturing technology widely used to manufacture complex parts in prominent sectors, including aerospace, biomedical, and automotive industries. However, during the printing process, the presence of an unstable vapor depression can lead to a type of defect called keyhole porosity, which is detrimental to the part quality. In this study, we developed an effective approach to locally detect the generation of keyhole pores during the printing process by leveraging machine learning and a suite of optical and acoustic sensors. Simultaneous synchrotron x-ray imaging allows the direct visualization of pore generation events inside the sample, offering high-fidelity ground truth. A neural network model adopting SqueezeNet architecture using single-sensor data was developed to evaluate the fidelity of each sensor for capturing keyhole pore generation events. Our comparative study shows that the near infrared images gave the highest prediction accuracy, followed by 100 kHz and 20 kHz microphones, and the photodiode sensitive to processing laser wavelength had the lowest accuracy. Using a single sensor, over 90% prediction accuracy can be achieved with a temporal resolution as short as 0.1 ms. A data fusion scheme was also developed with features extracted using SqueezeNet neural network architecture and classification using different machine learning algorithms. Our work demonstrates the correlation between the characteristic optical and acoustic emissions and the keyhole oscillation behavior, and thereby provides strong physics support for the machine learning approach.

36 MATERIALS SCIENCE↗
NASA NTRSDate not supplied

Correlations Between Porosity, Spatter, and Process Metrics for Powder Bed Fusion Laser Beam Metallic Additive Manufacturing

Components fabricated using the powder bed fusion laser beam metallic (PBF-LB/M)additive manufacturing process are the result of a multitude of weld passes conducted sequentially. Qualifying components for aerospace applications requires a thorough understanding of the process-structure-properties relationships. Porosity defects are known to have a strong adverse effect on the mechanical properties of a component. In particular, porosity defects created by lack of fusion have high aspect ratio morphologies leading to stress concentrations that become crack initiation sites. In the present work, the occurrence of spatter induced lack of fusion porosity was studied using synchronized in-situ process monitoring, additive manufacturing model-based process metrics, and high-resolution X-ray computed tomography. The results show that lack of fusion porosity is statistically correlated with unremoved welding spatter ejecta of the PBF-LB/M process and process metrics related to the hatching strategy.

Qualification↗
DOE OSTI2024

ExaCA grain structure predictions for laser powder bed fusion processing

This dataset contains simulated cross-sections of laser powder bed fusion grain structures produced using the microstructure model ExaCA, in turn using time-temperature history data produced using the heat transport model AdditiveFOAM. These predictions show the grain structure using various permutations of hatch spacing and nucleation density. Also contained in the dataset are the input files necessary to reproduce the results. AdditiveFOAM (https://github.com/ORNL/AdditiveFOAM) and ExaCA (https://github.com/LLNL/ExaCA), both open source software, are required to reproduce the results in this dataset using the given input files. This DOI was updated 12/09/2025.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Simulated Microstructures for Laser Powder Bed Fusion Additive Manufacturing Using Myna, AdditiveFOAM, and ExaCA

This dataset provides sample datasets containing voxelized, three-dimensional representations of simulated grain structures and crystallographic orientations that can result from laser powder bed fusion additive manufacturing. The six microstructure files each contain approximately 1 cubic millimeter of material (1 mm x 1 mm cross-section over 26 simulated layers of deposition). Some of the microstructures have columnar grains that extend across nearly the entire simulation domain, while others have more equiaxed or truncated columnar grains. The process conditions to generate these microstructures were from the Peregrine v2023-10 dataset (10.13139/ORNLNCCS/2008021). The codes used are publicly available and released under open-source licenses. Myna (https://github.com/ORNL-MDF/Myna) was used for configuration of the cases from the Peregrine v2023-10 HDF5 dataset and to run the simulation workflow. AdditiveFOAM (https://github.com/ORNL/AdditiveFOAM) was used to simulate the melt pool and generate solidification conditions. And ExaCA (https://github.com/LLNL/ExaCA ) was used to simulate the three-dimensional microstructures.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Ultrasonic characterization of material heterogeneities in stainless steel components produced by laser powder bed fusion

We introduce pulse-echo ultrasound as a method for characterizing the impact of powder bed fusion parameters on the properties of additively manufactured stainless-steel components, their material anisotropy, and location-dependent heterogeneity. Our results indicate that accurate characterization requires careful selection of ultrasonic propagation paths, which must consider the direction of additive layering, variations in processing parameters, and the component's geometry. We employed two distinct methods to estimate material properties from ultrasonic data: One assumes isotropy, while the other accounts for anisotropic interactions during the propagation of elastic waves. When applied to samples fabricated with laser energy densities ranging from 24 to 42 J/mm³ , these methods revealed transverse isotropy and weak anisotropy (quantified by small Thomsen parameters, ε = 0.0651 and γ = 0.0092) and less than a ∼6 % change in acoustic impedance. The assumption of isotropy, in this case, leads to small errors (less than 4 % or 1 % for Young's modulus in the build or transverse directions) when estimating orthotropic material properties using ultrasonic data measured along just two orthogonal directions, one of which must align with the build direction. By comparing ultrasonic measurements — which aggregate the spatial variability in material properties along the length of elastic wave propagation into a single value — with localized measurements obtained from surface nanoindentation, we uncovered and spatially profiled significant differences between the surface and interior properties. Specifically, the surface Young's modulus decreased from approximately 210 GPa to 180 GPa within a depth of about 3 mm. We attribute this surface-localized heterogeneity in PBF-fabricated components to distinct thermal histories experienced by the surface and interior regions. Collectively, the results of this study establish a framework for the ultrasonic characterization of material heterogeneity and anisotropy in material properties and demonstrate its application in additively manufactured metal components.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Efficient sensitivity analysis of the thermal profile in powder bed fusion of metals using hypercomplex automatic differentiation finite element method

Rapid cyclic temperature fluctuation occurring in powder bed fusion of metals using a laser beam (PBF-LB/M) influences the formation of flaws in printed parts. Consequently, there is a pressing need to enhance the quality of printed parts by developing innovative methodologies that can predict thermal histories and help uncover the intricate relationships between process parameters and thermal profiles. Sensitivity Analysis (SA) emerges as an essential tool for this, offering the potential for process optimization and enhanced quality control. Nonetheless, conventional SA methodologies often incur in excessive computational costs and potential numerical approximation errors. Here, to address this technical challenge, we present a novel method for SA that integrates the HYPercomplex-based Automatic Differentiation (HYPAD) technique with transient thermal simulations conducted via the finite element method (FEM). Leveraging this methodology, we efficiently and accurately perform SA for PBF-LB/M processes in a post-processing step. Compared to traditional methods like Finite Differences (FD), HYPAD-FEM required 96 % less computational time for obtaining sensitivities for 22 process parameters, under a comparative study conducted within the context of the 2018–02 AM benchmark of the National Institute of Standards and Technology. In summary, HYPAD-FEM offers superior efficiency and accuracy in SA over conventional methods, delivering the best sensitivity of a model without the need for step-size selection and problem or parameter-based implementations.

36 MATERIALS SCIENCE↗
DOE OSTI2024

A Microchannel Heat Exchanger Produced From a Metal Matrix Composite by Hybrid Laser Powder Bed Fusion and Inkjet Printing

Abstract This paper explores the production of an oxide dispersion strengthened (ODS) 304L stainless steel microchannel heat exchanger (HX) using a hybrid additive manufacturing process of laser powder bed fusion and inkjet printing. The study investigates the capabilities and economics of the hybrid inkjet-laser powder bed fusion (LPBF) process and evaluates the dimensional accuracy, functionality, and mechanical properties of the resulting ODS alloy. The effectiveness and pressure drop of the ODS heat exchangers produced by the hybrid LPBF tool are also determined. Results show that the inkjet-doped samples have a lower mean channel height with higher standard deviation than samples produced by LPBF alone. This is attributed to greater absorption of laser energy for the powder coated with the oxide precursor. The economic analysis shows that the hybrid process has a potential for reducing the unit cost of the heat exchanger based on cost modeling assumptions.

Engineering↗
DOE OSTI2025

A high strength Al-2Ni-0.5Zr conductor alloy fabricated via laser powder bed fusion

There is a current need for new aluminum alloy design strategies to target applications requiring high strength and conductivity with reductions in mass. A new lightweight Al-2Ni-0.5Zr (wt. %) conductor alloy was fabricated using laser powder bed fusion. A design of experiments probed the alloy's solidification cracking susceptibility. It was observed that solidification cracking was generally reduced with fast scan speeds, above 1500 mm/s, and smaller hatch spacings. The different cooling rates throughout the melt pool produced a heterogeneous distribution of cellular and equiaxed Al 3 Ni precipitates in the as-printed alloy. Additionally, the rapid solidification characteristic of laser powder bed fusion created a super-saturated Zr solid solution. An aging heat treatment at 375 °C for 24 h imparted strengthening through the precipitation of L1 2 -Al 3 Zr nanoprecipitates, which counteracted the softening caused by the fragmentation and coarsening of Al 3 Ni precipitates. The yield strength increased from 138 MPa in the as-printed condition to 168 MPa after aging, while the ductility remained constant at ∼21%. The aging treatment simultaneously increased the electrical conductivity from 40.8% IACS (International Annealed Copper Standard) to 53.5% IACS. Modeling of the strengthening mechanisms and electrical conductivity contributions rationalized the simultaneous increase in strength and conductivity upon aging. Furthermore, the strengthening efficacy of the Al 3 Ni and L1 2 -Al 3 Zr precipitates, combined with the low Ni and Zr solubility in the FCC Al matrix, facilitated both high strength and electrical conductivity. Overall, the combination of strength and electrical conductivity positions this alloy as a suitable choice for additively manufactured lightweight conductors.

Additive manufacturing↗
DOE OSTI2024

Solidification and crystallographic texture modeling of laser powder bed fusion Ti-6Al-4V using finite difference-monte carlo method

Laser powder bed fusion (LPBF) additive manufacturing makes near-net-shaped parts with reduced material cost and time, rising as a promising technology to fabricate Ti-6Al-4V, a widely used titanium alloy in aerospace and medical industries. However, LPBF Ti-6Al-4V parts produced with 67° rotation between layers, a scan strategy commonly used to reduce microstructure and property inhomogeneity, have varying grain morphologies and weak crystallographic textures that change depending on processing parameters. Here, this study predicts LPBF Ti-6Al-4V solidification at three energy levels using a finite difference-Monte Carlo method and validates the simulations with large-area electron backscatter diffraction (EBSD) scans. The developed model accurately shows that a <001> texture forms at low energy and a <111> texture occurs at higher energies parallel to the build direction but with a lower strength than the textures observed from EBSD. A validated and well-established method of combining spatial correlation and general spherical harmonics representation of texture is developed to calculate a difference score between simulations and experiments. The quantitative comparison enables effective fine-tuning of nucleation density (N 0 ) input, which shows a nonlinear relationship with increasing energy level. Future improvements in texture prediction code and a more comprehensive study of N 0 with different energy levels will further advance the optimization of LPBF Ti-6Al-4V components. These developments contribute a novel understanding of crystallographic texture formation in LPBF Ti-6Al-4V, the development of robust model validation and calibration pipeline methodologies, and provide a platform for mechanical property prediction and process parameter optimization.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Laser Powder Bed Fusion of Steels for Nuclear Applications

This report provides an update on laser powder bed fusion of steels for nuclear applications. This report is a Milestone 3 deliverable in FY2024, under work package CT-24AN130401 to support research and qualification activities supported by the Advanced Materials and Manufacturing Technologies (AMMT) program here at Argonne National Laboratory (ANL). Continuing from FY23, the focus of FY24 for ANL includes further optimization of process parameters for three alloys: A709, G91, G92. The work package also includes fabricating test samples to conduct a thorough microstructural analysis and perform preliminary mechanical testing. For the same, we have used CALPHAD-based thermodynamic kinetic modeling to optimize the experimental activities.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Effect of Processing Parameters on Recrystallization During Hot Isostatic Pressing of Stellite-6 Fabricated Using Laser Powder Bed Fusion Technique

Crack-free Stellite-6 alloy was fabricated using the laser powder bed fusion technique equipped with a heating module as the first attempt. Single tracks were printed with a build plate heated to 400 °C to identify the processing window. Based on the melt pool dimensions, two combinations (sample A: 300 W/750 mm/s and sample B: 275 W/1000 mm/s) were identified to print the cubes. The as-printed microstructure comprised FCC-Co dendrites with M7C3 in the interdendritic region. W-rich M6C particles were found in the overlapping regions between the melt pools, matching the Scheil simulations. However, gas pores were observed due to the higher nitrogen and oxygen content of the feedstock requiring hot isostatic pressing (HIP) at 1250 °C and 150 MPa for 2 h. Sample A was partially recrystallized with slightly coarsened M7C3, while sample B underwent complete recrystallization followed by grain growth along with higher coarsening of the M7C3 after HIP. The varying recrystallization behavior can be attributed to the difference in residual stresses and grain aspect ratio in the as-built condition dictated by laser power and scanning speed. The microhardness after HIP was slightly higher than its wrought counterpart, indicating no severe impact of post-processing on the properties of Stellite-6 alloy.

Sridar, Soumya (ORCID:0000000306775408)↗
DOE OSTI2025

Fatigue behavior of low-cost, non-spherical Ti-6Al-4V powder processed via laser powder bed fusion

Hydride-dehydride Ti-6Al-4V powder with particle size distribution of 75–175 μm were used to manufacture fatigue samples. Optimized processing parameters were used to maintain a relative density of >99.5% in the samples. Fatigue tests were carried out in R = σ min /σ max = -1 condition under stresses ranging from 150 to 500 MPa and the results were compared to samples that were additively manufactured using spherical powders. The fatigue lives were similar between the two types of powder; i.e., powder morphology has no effect on fatigue performance. However, the high surface roughness and martensitic microstructure resulting from the laser powder bed fusion process result in poor performance compared to samples machined from conventionally produced materials. In conclusion, crack initiation occurred consistently from surface defects because of high surface roughness of the additively manufactured parts.

36 MATERIALS SCIENCE↗