SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Geodesic array of heaters powered by separate electrical supply unit and silicon controlled-rectifier (SCR) control unit produces controlled temperatures over independent zones. Arrays conform to and enclose almost any shape with close thermal coupling and are programmed to reproduce almost any desired time/temperature distribution.
The mean surfaces of several regions of the world's oceans were estimated using GEOS-3 altimeter data. The northwest Atlantic, the northeast Pacific off the coast of California, the Indian Ocean, the southwest Pacific, and the Phillipine Sea are included. These surfaces have been oriented with respect to a common earth center-of-mass system by constraining the separate solutions to conform to precisely determined laser reference control orbits. The same reference orbits were used for all regions assuring continuity of the separate solutions. Radial accuracies of the control orbits were in the order of one meter. The altimeter measured sea surface height crossover differences were minimized by the adjustment of tilt and bias parameters for each pass with the exception of laser reference control passes. The tilt and bias adjustments removed long wavelength errors which were primarily due to orbit error. Ocean tides were evaluated. The resolution of the estimated sea surfaces varied from 0.25 degrees off the east coast of the United States to about 2 degrees in part of the Indian Ocean near Australia. The rms crossover discrepancy after adjustment varied from 30 cm to 70 cm depending upon geographic location. Comparisons of the altimeter derived mean sea surface in the North Atlantic with the 5 feet x 5 feet GEM-8 detailed gravimetric geoid indicated a relative consistency of better than a meter.
A 15-m-diameter antenna was tested to verify that dimensional tolerances for acceptable performance could be achieved and to verify structural, electromagnetic, and mechanical performance predictions. This antenna utilized the hoop column structure, a gold plated molybdenum mesh reflector, and 96 control cables to adjust the reflector conformance with a paraboloid. The dimensional conformance of the antenna structure and surface was measured with metric camera and theodolites. Near field pattern data were used to assess the electromagnetic performance at five frequencies from 2.225 to 11.6 GHz. The reflector surface was adjusted to greatly improve electromagnetic performance with a finite element model and the surface measurements. Measurement results show that antenna surface figure and adjustments and electromagnetic patterns agree well with predictions.
Atomic Layer Deposition (ALD) is a cost effective nano-manufacturing technique that allows for the conformal coating of substrates with atomic control in a benign temperature and pressure environment. Through the introduction of paired precursor gases thin films can be deposited on a myriad of substrates ranging from glass, polymers, aerogels, and metals to high aspect ratio geometries. This talk will focus on the utilization of ALD for engineering applications.
Atomic Layer Deposition has been instrumental in providing a deposition method for multiple space flight applications. It is well known that ALD is a cost effective nanoadditive-manufacturing technique that allows for the conformal coating of substrates with atomic control in a benign temperature and pressure environment. Through the introduction of paired precursor gases, thin films can be deposited on a myriad of substrates from flat surfaces to those with significant topography. By providing atomic layer control, where single layers of atoms can be deposited, the fabrication of metal transparent films, precise nano-laminates, and coatings of nano-channels, pores and particles is achievable. The feasibility of this technology for NASA line of business applications range from thermal systems, optics, sensors, to environmental protection. An overview of this technology will be presented.
Atomic Layer Deposition (ALD) is a cost-effective nanoadditive-manufacturing technique that allows for conformal coating of substrates with atomic control in a benign temperature and pressure environment. Using paired precursor gases, thin films can be deposited on flat or textured surfaces ranging from glass, polymers, aerogels, and metals. Through atomic layer control, where single layers of atoms are deposited, fabrication of metal transparent films, nano-laminates, and coatings of nano-channels and pores is achievable. Reaction mechanisms in ALD are normally self-limiting, allowing for atomically accurate control of nanometer (nm) thicknesses. Therefore, high uniformity and precise thickness control make ALD an attractive process for the creation of novel nano-scale devices. Decreases in resistivity and density of electrical wire are needed to improve the function of electronics, electric motors and cables. Such improvements may be accomplished by adding ballistically conducting, metallic carbon nanotubes (CNT) to Cu. ALD was used to coat multiple substrates including CNT with Cu in an effort to make CNT-Cu composites which is more conductive and less dense than Cu. In addition, ALD can be used to as a method to deposit the catalyst layer seed layer for CNT growth using Ni. The ALD of copper metallic films can follow multiple reaction pathways depending on the ALD precursors used. For this work the reaction pathway was deposition of copper oxide and then post process annealing in a hydrogen environment. Copper(II) diacetylacetonate (Cu(acac)2) and ozone are used as precursors for copper oxide. As-deposited copper oxide films prepared at 180°C resulted in a growth per cycle of 1.0 A/cycle with low film resistivity.
Pairwise Trajectory Management (PTM) is an Interval Management (IM) concept that utilizes airborne and ground-based capabilities to enable the implementation of airborne pairwise spacing capabilities in oceanic regions. The goal of PTM is to use airborne surveillance and tools to manage an "at or greater than" inter-aircraft spacing. Due to the precision of Automatic Dependent Surveillance-Broadcast (ADS-B) information and the use of airborne spacing guidance, the PTM minimum spacing distance will be less than distances a controller can support with current automation systems that support oceanic operations. Ground tools assist the controller in evaluating the traffic picture and determining appropriate PTM clearances to be issued. Avionics systems provide guidance information that allows the flight crew to conform to the PTM clearance issued by the controller. The combination of a reduced minimum distance and airborne spacing management will increase the capacity and efficiency of aircraft operations at a given altitude or volume of airspace. This paper provides an overview of the proposed application, description of a few key scenarios, high level discussion of expected air and ground equipment and procedure changes, overview of a potential flight crew human-machine interface that would support PTM operations and some initial PTM benefits results.
Pairwise Trajectory Management (PTM) is an Interval Management (IM) concept that utilizes airborne and ground-based capabilities to enable the implementation of airborne pairwise spacing capabilities in oceanic regions. The goal of PTM is to use airborne surveillance and tools to manage an "at or greater than" inter-aircraft spacing. Due to the accuracy of Automatic Dependent Surveillance-Broadcast (ADS-B) information and the use of airborne spacing guidance, the minimum PTM spacing distance will be less than distances a controller can support with current automation systems that support oceanic operations. Ground tools assist the controller in evaluating the traffic picture and determining appropriate PTM clearances to be issued. Avionics systems provide guidance information that allows the flight crew to conform to the PTM clearance issued by the controller. The combination of a reduced minimum distance and airborne spacing management will increase the capacity and efficiency of aircraft operations at a given altitude or volume of airspace. This document provides an overview of the proposed application, a description of several key scenarios, a high level discussion of expected air and ground equipment and procedure changes, a description of a NASA human-machine interface (HMI) prototype for the flight crew that would support PTM operations, and initial benefits analysis results. Additionally, included as appendices, are the following documents: the PTM Operational Services and Environment Definition (OSED) document and a companion "Future Considerations for the Pairwise Trajectory Management (PTM) Concept: Potential Future Updates for the PTM OSED" paper, a detailed description of the PTM algorithm and PTM Limit Mach rules, initial PTM safety requirements and safety assessment documents, a detailed description of the design, development, and initial evaluations of the proposed flight crew HMI, an overview of the methodology and results of PTM pilot training requirements focus group and human-in-the-loop testing activities, and the PTM Pilot Guide.
General curvilinear coordinate systems are considered along with the error induced by coordinate systems, basic differential models for coordinate generation, elliptic grid generation, conformal grid generation, algebraic grid generation, orthogonal grid generation, patched coordinate systems, and solid mechanics applications of boundary fitted coordinate systems. Attention is given to coordinate system control and adaptive meshes, the application of body conforming curvilinear grids for finite difference solution of external flow, the use of solution adaptive grids in solving partial differential equations, adaptive gridding for finite difference solutions to heat and mass transfer problems, and the application of curvilinear coordinate generation techniques to the computation of internal flows. Other topics explored are related to the solution of nonlinear water wave problems using boundary-fitted coordinate systems, the numerical modeling of estuarine hydrodynamics on a boundary-fitted coordinate system, and conformal grid generation for multielement airfoils.
The Local Flow Management/Profile Descent (LFM/PD) algorithm designed for the NASA Transport System Research Vehicle program is described. The algorithm provides fuel-efficient altitude and airspeed profiles consistent with ATC restrictions in a time-based metering environment over a fixed ground track. The model design constraints include accommodation of both published profile descent procedures and unpublished profile descents, incorporation of fuel efficiency as a flight profile criterion, operation within the performance capabilities of the Boeing 737-100 airplane with JT8D-7 engines, and conformity to standard air traffic navigation and control procedures. Holding and path stretching capabilities are included for long delay situations.
NASA's first Air Traffic Management (ATM) Technology Demonstration (ATD-1) was created to facilitate the transition of mature ATM technologies from the laboratory to operational use. The technologies selected for demonstration are the Traffic Management Advisor with Terminal Metering (TMA-TM), which provides precise time-based scheduling in the terminal airspace; Controller Managed Spacing (CMS), which provides terminal controllers with decision support tools enabling precise schedule conformance; and Interval Management (IM), which consists of flight deck automation that enables aircraft to achieve or maintain a precise spacing interval behind a target aircraft. As the percentage of IM equipped aircraft increases, controllers may provide IM clearances to sequences, or strings, of IM-equipped aircraft. It is important for these strings to maintain stable performance. This paper describes an analytic analysis of the string stability of the latest version of NASA's IM algorithm and a fast-time simulation designed to characterize the string performance of the IM algorithm. The analytic analysis showed that the spacing algorithm has stable poles, indicating that a spacing error perturbation will be reduced as a function of string position. The fast-time simulation investigated IM operations at two airports using constraints associated with the midterm airspace, including limited information of the target aircraft's intended speed profile and limited information of the wind forecast on the target aircraft's route. The results of the fast-time simulation demonstrated that the performance of the spacing algorithm is acceptable for strings of moderate length; however, there is some degradation in IM performance as a function of string position.
In four-dimensional trajectory (4DT) Surface Trajectory-Based Operations (STBO), aircraft are assigned a conflict-free 4DT which defines an expected location (x,y coordinates) at all times, t, along the taxi route (with altitude, being fixed). These 4DTs afford the highest temporal certainty at all points along the taxi route, and at the departure runway. In the present study, a 4DT flight deck display was presented on the Airport Moving Map (AMM) to support pilot conformance to a 4DT clearance while taxiing under manual control. This pilot-in-the-loop simulation compared the effect of 4DT flight deck display formats on distance from the expected 4DT location, conformance to the displayed tolerance band, eyes-out time, and pilot ratings of safety and workload. In the defined-tolerance display format, a graphical representation of the expected 4DT location, with a distance-based allowable-tolerance band, was depicted on the AMM. Two defined-tolerance band sizes were tested: plus or minus 164 feet and plus or minus 405 feet. In the undefined-tolerance display format, the expected 4DT location was displayed graphically on the AMM, with no indicated allowable-tolerance bounds. Each taxi trial included 4DT speed changes (two or five, per trial) and a range of 4DT taxi speeds. Results showed that the larger (plus or minus 405 feet) defined-tolerance band yielded higher conformance levels than the smaller (plus or minus 164 feet) band, with pilots staying within the specified and displayed conformance bounds more in the larger (99.71%) than the smaller defined-tolerance band (93.37 percent). However, in terms of being able to predict the location of the aircraft compared to the expected 4DT location, the smaller defined-tolerance band resulted in pilots keeping their aircraft closer to the 4DT location, for both average distance and for a given confidence interval (e.g., 95 percent), than either the larger defined-tolerance band or the undefined-tolerance display format. The larger tolerance band yielded more “eyes-out-the-window” time than the smaller tolerance band. Pilots also rated taxing with the larger tolerance band as safer than the smaller tolerance band.
A human-in-the-loop simulation was conducted to examine the effects of varying levels of trajectory prediction uncertainty on air traffic controller workload and performance, as well as how strategies and the use of decision support tools change in response. This paper focuses on the strategies employed by two controllers from separate teams who worked in parallel but independently under identical conditions (airspace, arrival traffic, tools) with the goal of ensuring schedule conformance and safe separation for a dense arrival flow in en route airspace. Despite differences in strategy and methods, both controllers achieved high levels of schedule conformance and safe separation. Overall, results show that trajectory uncertainties introduced by wind and aircraft performance prediction errors do not affect the controllers' ability to manage traffic. Controller strategies were fairly robust to changes in error, though strategies were affected by the amount of delay to absorb (scheduled time of arrival minus estimated time of arrival). Using the results and observations, this paper proposes an ability to dynamically customize the display of information including delay time based on observed error to better accommodate different strategies and objectives.
This paper presents a new approach in applying the blending function method to the generation of structured finite-difference meshes. It is shown that the surface equation developed by Coons (1967) can be easily adapted to generate two-dimensional meshes, and its extension to hyperspace allows the construction of three-dimensional meshes. The robust method in its basic form blends among the boundary curves/surfaces conforming to their intrinsic slopes. When parameter-controlled boundary-slope corrections are introduced, it is possible to establish varying degrees of orthogonality along the boundaries. Additional controls are made possible by moving points in the parameter space, which affects the movement of points in the physical space. The combination of these controls provides a simple and yet powerful means for exploiting the blending-function method to satisfy the needs of practical CFD applications. Results from a validation program for two-dimensions are shown for a variety of geometries.
Design, fabrication, and testing of inverter module for closed loop advanced control signal processor - thin film circuit, and conformal coating and encapsulation
Among the topics discussed are: access control models for a distributed CAIS-conforming system; a knowledge-based advisory system for casualty procedures; and automated interactive simulation modeling system. Consideration is also given to: reusable software concepts and software development methodologies; the electronic device aspects of neutral network memories; an expert system for automated satellite anomaly resolution; and the use of automatic programming techniques for fault-tolerant computing systems. Among additional topics discussed are: systems approaches to software fault tolerance; a Space Shuttle navigation validation system; and a vision-based road following system for an autonomous land vehicle.
Unitary array of sensors measures temperatures at points distributed over designated area on surface. Useful in measuring surface temperatures of aerodynamic models and thermally controlled objects. Made of combination of integrated-circuit microchips and film circuitry. Temperature-sensing chips scanned at speeds approaching 10 kHz. Operating range minus 40 degrees C to 120 degrees C. Flexibility of array conforms to curved surfaces. Multiplexer eliminates numerous monitoring cables. Control of acquisition and recording of data effected by connecting array to microcomputers via suitable interface circuitry.
The Federal Aviation Administration's (FAA) Next Generation Air Transportation System (or NextGen) is being designed to support the predicted increases in traffic volume and to increase the capacity, efficiency and safety of the National Airspace System (NAS). The Federal Aviation Administration (FAA) identifies Performance-Based Navigation (PBN) as a key enabling capability of NextGen and is actively publishing PBN procedures at major airports throughout the United States. Standard Terminal Arrival Routes (STARs), procedures, and approaches are designed to facilitate fuel-efficient continuous descent operations. However, their use is limited during periods of high traffic demand due to the complexity of merging multiple streams of aircraft to the same airport. As a result, most arrivals in the Terminal Radar Approach Control (TRACON) area continue to be controlled using radar vectoring and step-down descents, resulting in high workload for controllers and diverting aircraft from efficient PBN trajectories. To address this issue, NASA developed the Terminal Sequencing and Spacing (TSS) system, an advanced arrival management technology that combines time-based scheduling and controller-based precision spacing tools. TSS is a ground-based controller automation tool that facilitates sequencing and merging arrivals on Performance-Based Navigation (PBN) routes, especially during highly congested demand periods. The two main components of TSS are: 1) a scheduler that de-conflicts merging arrivals in the terminal area by computing appropriate arrival times to the runway threshold and upstream terminal merge points, and 2) a set of Controller-Managed Spacing (CMS) decision support tools to efficiently assist schedule conformance. Sixteen high-fidelity human-in-the-loop simulations involving more than five hundred hours of evaluation time, were conducted to mature TSS from proof-of-concept design to a fully functional prototype. Results indicate high controller use and acceptability of the CMS tools as well as improved PBN route conformance (Figure 2). The TSS technology was transferred to the FAA in 2014, and it is targeted for deployment to several busy airports in the U.S. starting in 2018. Potential enhancements to TSS using DataComm will also be presented.