Search NASA⌕ Search

SEARCH · Search NASA

Results for “curing processes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Shock-induced chemistry and high strain-rate viscoelastic behavior of a phenolic polymer

We use impact experiments and a finite element model (up to 1.2 GPa), and molecular dynamics simulations (up to 60 GPa), to examine the behavior of a phenolic polymer under shock compression, spanning both nonreactive and reactive regimes. In the nonreactive regime, relaxation following compression at strain rates of ∼105 s−1 can be explained by viscoelasticity observed at ordinary laboratory rates (≲1 s−1) by accounting for the temperature dependence of the phenolic β-transition. Reasonable agreement is found between the measured shock Hugoniot up to 1.2 GPa and molecular dynamics simulation for cross-linked structures of comparable density. We also observed a first-order mechanical transition near 0.36 GPa shock stress and estimated a spall strength of 0.102 GPa and Hugoniot elastic limit of 1–2 GPa. The shock stress is found to vary up to 24% among phenolics made with different resin and/or cure processes. Finally, molecular dynamics simulations are used to identify a reactive regime at shock pressures ≳20 GPa that is characterized by chemically driven, rate-dependent relaxation processes, including dehydrogenation and dehydration reactions that promote the formation of a dense, highly cross-linked carbonaceous solid and the release of light volatiles.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Encapsulation Residual Stress and Ferrite Loss in Inductive Coil Assemblies

As inductive wireless charging reaches higher power levels, thermal management and mechanical durability become more critical. To address these concerns, past works have demonstrated the benefit of encapsulating coil assemblies in thermally conductive materials. However, due to the sensitivity of the MnZn ferrites commonly used in coil assemblies to mechanical stress, care must be taken to avoid creating large stresses in the ferrite that cause higher hysteresis loss. The stress formation in the encapsulant curing process is overviewed and modeled and an experiment is performed to demonstrate the effect in a small-scale coil assembly. Finally, the effect is shown in the reduced coil-coil efficiency of a first generation high power inductive power transfer prototype using a stiff epoxy compared to better performance in a second prototype using a softer thermally-conductive silicone encapsulant.

Foote, Andrew↗
DOE OSTI2026

Plasticizer-Free Gradient-Crosslinked Polyurethane Electrolyte for Room-Temperature Solid-State Lithium Batteries

Polymer-based solid-state electrolytes are promising for next-generation lithium metal batteries, yet their limited ionic conductivity and mechanical stability at ambient conditions remain key challenges. Herein, we report a novel gradient crosslinked polymer electrolyte (PU/PUA/PU) synthesized via a sequential in situ UV-curing process that integrates a mechanically robust polyurethane acrylate (PUA) core with soft linear polyurethane (PU) interfaces. This all-solid membrane operates without any liquid plasticizer and the interfacial PU layers ensure low interfacial resistance and intimate electrode contact, while the PUA core provides enhanced dimensional stability and dendrite suppression. As a result, the gradient electrolyte delivers an impressive ∼2.6 × 10 −4 S cm −1 ionic conductivity at 25 °C (two orders of magnitude higher than conventional PEO) and remains electrochemically stable >5 V (vs Li + /Li). Structural analysis confirms the formation of a well-defined crosslinked network with suppressed crystallinity and expanded interchain spacing. Electrochemical impedance spectroscopy (EIS) and linear sweep voltammetry (LSV) further validate these properties. When applied in a Li||NMC811 cell, the PU/PUA/PU electrolyte delivers stable cycling with high capacity at both 60 °C and 25 °C, demonstrating its potential for room-temperature solid-state battery applications without reliance on plasticizers or heating. In conclusion, this gradient design offers a practical path toward ambient-condition operation of solid-state lithium batteries, providing a paradigm for overcoming the traditional trade-off between ionic conductivity and mechanical robustness.

25 ENERGY STORAGE↗
DOE OSTI2022

Low-Temperature Architected Cementation Agents (LAMINAE)

The cement industry contributes 5-9% of all anthropogenic CO 2 . At the same time, current concrete curing processes are passive, with little-to-no control over microstructure. The LAMINAE process offers the potential for a low-temperature pathway for producing cementitious aluminosilicate hydrate (zeolite) structures which: (a) reduces the energy burden of cement production by 30%, (b) reduces CO 2 emissions by 60%, and (c) offers microstructure control as was implicitly ensured in Roman concrete. This project generated data and engineering correlations to support further scale up and design of initial commercial processes.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Porous Polymeric Materials FY24 PDRD Final Report

Fillers and pore formers are used in many materials at Kansas City National Security Campus (KCNSC) to fine tune density and stiffness. Current off-the-shelf options such as urea and Expancel do not always provide the desired properties. This project investigated several methods for introducing porosity in rigid polymers such as epoxy and polyurethane. This work was done at partnering universities to identify a variety of methods to create porous polymeric materials. The University of Oklahoma (OU) investigated emulsion templating of epoxy, where the epoxy is mixed with a surfactant and water to form an emulsion. The emulsion is then molded and cured. During the cure process, water droplets evaporate to form porous structures. Total porosity can be tuned by changing the concentration of water added to the polymer. The University of Kansas (KU) investigated the synthesis of phenolic microballoons by spray drying, as well as methods of incorporating removable porogens into epoxy and polyurethane materials to create polymeric foams.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Optimizing Adhesion: Evaluating B-Stage Epoxy for Bonding [Poster]

The application of increased pressure during the curing process of B-stage epoxy has been hypothesized to enhance the adhesive properties and bond strength in printed wiring board (PWB) assembly. This study aimed to investigate the correlation between pressure application and the performance of B-stage epoxy.

42 ENGINEERING↗
DOE OSTI2021

Applications of Kinetic Methods in Thermal Analysis: A Review

Determining kinetic parameters such as activation energy (Ea), pre-exponential factor (A), rate constants, and reaction order (n) via thermal analysis techniques is important to material synthesis and fabrication, industrial production, biomedicals, energy storage, catalysis, etc. Various kinetic methods based on the non-isothermal techniques have been developed to obtain the kinetic parameters. In this review, we focus on introducing various kinetic methods in non-isothermal analysis and their applications in different reactions, including thermal decomposition, solid-state phase transformation, crystallization, thermal ignition, curing process, etc.

Zhang, Xin↗
DOE OSTI2024

Porous Polymer Structures with Tunable Mechanical Properties Using a Water Emulsion Ink

Recently, the manufacturing of porous polydimethylsiloxane (PDMS) with engineered porosity has gained considerable interest due to its tunable material properties and diverse applications. An innovative approach to control the porosity of PDMS is to use transient liquid phase water to improve its mechanical properties, which has been explored in this work. Adjusting the ratios of deionized water to the PDMS precursor during blending and subsequent curing processes allows for controlled porosity, yielding water emulsion foam with tailored properties. The PDMS-to-water weight ratios were engineered ranging from 100:0 to 10:90, with the 65:35 specimen exhibiting the best mechanical properties with a Young’s Modulus of 1.17 MPa, energy absorption of 0.33 MPa, and compressive strength of 3.50 MPa. This led to a porous sample exhibiting a 31.46% increase in the modulus of elasticity over a bulk PDMS sample. Dowsil SE 1700 was then added, improving the storage capabilities of the precursor. The optimal storage temperature was probed, with -60 °C resulting in great pore stability throughout a three-week duration. The possibility of using these water emulsion foams for paste extrusion additive manufacturing (AM) was also analyzed by implementing a rheological modifier, fumed silica. Fumed silica’s impact on viscosity was examined, revealing that 9 wt% of silica demonstrates optimal rheological behaviors for AM, bearing a viscosity of 10,290 Pa·s while demonstrating shear-thinning and thixotropic behavior. This study suggests that water can be used as pore-formers for PDMS in conjunction with AM to produce engineered materials and structures for aerospace, medical, and defense industries as sensors, microfluidic devices, and lightweight structures.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Hexagonal Distributed Embedded Energy Converters (HexDEECs)

The HexDEEC is a small, characteristic length approximating a centimeter, energy transducer that converts the dynamic deformations of its elastomer housing into electricity through a variable capacitance charging-discharging cycle. This device is a type of Distributed Embedded Energy Converter Technology (DEEC-Tec), a new domain for marine renewable energy research that utilizes a conglomeration of small distributed embedded energy converters (DEECs) that, in aggregate, form larger metamaterial frameworks. These resulting DEEC-Tec metamaterials can then, in turn, be used to construct flexible ocean wave energy converters called flexWECs, which can utilize a broad band of ocean wave frequencies and lack highly loaded rigid bodies. These systems also provide new avenues of wave energy harvesting such as actively transforming topologies (e.g., shape and form) and morphologies (e.g., stiffness and damping throughout its entire structure) in real time. Presented, is one specific type of DEEC: the HexDEEC, which is currently being developed by the United States National Renewable Energy Laboratory. This transducer shows promise in aiding the adoption and further development of the DEEC-Tec domain. The following presentation focuses on the promise of this technology and current work being done to analyze the performance of an individual HexDEEC design. The HexDEEC is composed of a hyperelastic hexagonal housing, nominally silicon rubber, with six electrodes on its inner faces. The upper three electrodes share the same charge while the lower three electrodes oppose the upper electrode charges. Externally, the HexDEEC has two arms extending away from the middle vertices of the hexagon. Via principles governing the relationship between electrical capacitance and electrical potential (voltage and charge), electricity is generated when the HexDEEC's arms are dynamically pulled or released under tensile loading, as doing so causes the distance between the upper and lower sets of electrodes to change - varying the energy converter's overall capacitance. Analytical and numerical modeling is being used to evaluate the mechanics and electrical energy generated by the HexDEEC. Equations to describe the capacitance and electrostatic forces acting on this unique system have been developed and implemented into the numerical modeling software STAR-CCM+, along with models to describe its hyperelastic material, such as the Mooney-Rivlin 3-parameter model. So far, an initial design has been analyzed and we plan to further optimize it to increase power production. Individual HexDEECs have been fabricated by drawing uncured liquid silicon rubber into molds via vacuum pressure. To simplify manufacturing, HexDEEC sub-components - e.g., electrodes, wires - can be placed within those molds such that they are directly embedded into the hexagonal housing during the curing process. Furthermore, DEEC-Tec metamaterials can be created by interweaving or sequentially layering multiple HexDEEC strands together. The HexDEEC based metamaterial could then generate electricity through its gross deformations. Ultimately, HexDEECs represent a specific type of energy transducer that can be leveraged, by the DEEC-Tec domain, to create metamaterials used to construct novel flexWECs.

DEEC-Tec↗
DOE OSTI2022

Hexagonal Distributed Embedded Energy Converters (HexDEECs)

Distributed Embedded Energy Converter Technologies (DEEC-Tec) is a new domain for marine renewable energy research that utilizes a conglomeration of small distributed embedded energy converters (DEECs) that, in aggregate, form larger metamaterial frameworks. These resulting DEEC-Tec metamaterials can then, in turn, be used to construct flexible ocean wave energy converters called flexWECs. DEEC-Tec enables flexWECs: (i) to be inherently broad-banded ocean wave frequency energy converters and (ii) to have an inherent lack of highly loaded rigid bodies. The DEEC-Tec domain also benefits the marine renewable energy domain by inherently availing ways that marine energy can be harvested and converted that heretofore has not yet been considered possible: real-time execution of transforming topologies (e.g., actively changing a flexWEC's shape and form) and morphologies (e.g., actively changing a flexWEC's stiffness and damping throughout its entire structure). Presented, is one specific type of DEEC, a HexDEEC, that shows promise in aiding the adoption and further development of the DEEC-Tec domain - it is a small energy transducer being developed by the United States National Renewable Energy Laboratory. The HexDEEC is a small (characteristic length approximating a centimeter) energy transducer that converts the dynamic deformations of an elastomer into electricity through a charging-discharging cycle of a capacitor whose capacitance is varied by those elastic deformations. The HexDEEC is composed of a hyperelastic hexagonal housing (nominally silicon rubber) with six electrodes on its inner faces. The upper three electrodes share the same charge while the lower three electrodes oppose the upper electrode charges. Externally, the HexDEEC has two arms extending away from the middle vertices of the hexagon. Via principles governing the relationship between electrical capacitance and electrical potential (voltage and charge), electricity is generated when the HexDEEC's arms are dynamically pulled or released under tensile loading as doing so causes the distance between the upper and lower sets of electrodes to change - varying the energy converter's overall capacitance. Analytical and numerical modeling have already been used to estimate the electrical energy produced by a HexDEEC. The cursory models approximate the HexDEEC as a parallel plate variable capacitor - simplifying from six to two opposing plates with a constant dielectric volume between those two plates. To account for the elastic HexDEEC material properties, software such as SolidWorks and STAR-CCM+ have been used to generate hyperelastic models; notably, Mooney-Rivlin based models. Individual HexDEECs have been fabricated by drawing uncured liquid silicon rubber into molds via vacuum pressure. To simplify manufacturing, HexDEEC sub-components - e.g., electrodes, wires - can be placed within those molds such that they are directly embedded into the hexagonal housing during the curing process. Furthermore, DEEC-Tec metamaterials can be created by interweaving or sequentially layering multiple HexDEEC strands together. The HexDEEC based metamaterial could then generate electricity through its gross deformations. Ultimately, HexDEECs represent a specific type of energy transducer that can be leveraged, by the DEEC-Tec domain, to create metamaterials used to construct novel flexWECs.

DEEC-Tec↗
DOE OSTI2021

Cement stress and microstructure evolution during curing in semi-rigid high-pressure environments

The process of cement slurry curing into a solid has a direct effect on the initial state of stress in a composite concrete and steel structure. Failure models for critical infrastructure and wellbores could benefit from measurements of this initial stress because it greatly influences structural performance. Here, we present measurements of the initial stress state (total stress, effective stress, and pore pressure) of multiple cement formulations cured under a high-pressure of 40 MPa within a semi-rigid steel pipe. Our results show that cements cured in this restrained environment exhibit dense microstructures with low permeability (nano-Darcy), develop an anisotropic stress state greater than zero and less than the curing pressure, and undergo a staged curing process where hydration and mechanical behaviors evolve from a slurry into a pre-stressed porous medium. Both drained and undrained scenarios were investigated, revealing a feedback from the semi-rigid boundary towards improved cement performance.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Higher Throughput, Lower Cost Processing of Flexible Perovskite Solar Cells by Photonic Curing

The objectives of this SETO project are to explore whether photonic curing can be used to perform annealing in perovskite solar cell (PSC) fabrication, and if so, whether it can enable high-throughput PSC manufacturing. The successful outcome of the project will reduce manufacturing cost towards realizing the SETO goal of the Levelized cost of electricity (LCOE) $0.03/kWh by 2030. The project is a collaboration between Hsu’s group at the University of Texas at Dallas (UTD) and NovaCentrix, an Austin TX based company that pioneered the PulseForge® photonic curing tools and has expertise in applying this technology to printed electronics. Thin-film synthesis typically involves a thermal annealing step to convert from precursors to final material phases, to obtain the desired crystalline phase, or to improve materials structural or electrical properties. However, thermal annealing typically requires high temperatures that are incompatible with inexpensive plastic substrates and annealing times lasting tens-to-hundreds of minutes, making it incompatible with roll-to-roll (R2R) manufacturing at a desirable web speed. Photonic curing uses a flash Xe lamp to deliver short (20 µs to 100 ms) but high intensity (up to 50 kW/cm 2 ) pulses of broadband light (200 – 1500 nm) to the sample. It has been successfully applied to sinter printed metal nanoparticle inks into conductive patterns. This project aimed to extend the applications of photonic curing to convert halide perovskite films and transparent metal oxide transport layers. Despite the interruption by COVID-19, we have achieved significant accomplishments to establish photonic curing as a viable technology for the high-throughput manufacturing of PSCs. (1) We demonstrated that photonic curing can convert both metal oxide transport layer and halide perovskite absorber in the PSCs and successfully made flexible PSCs on Corning Willow glass® (WG)/ indium tin oxide (ITO) substrates without any thermal annealing steps. These photonically cured devices achieve performance comparable to conventional thermally annealed devices but were fabricated with a total processing time reduced by six orders of magnitude. We also show that photonic curing can achieve desirable web speed (up to 26 m/min) and large-area uniformity. (2) By establishing photonic curing processing phase spaces for the perovskite, we show that the longer pulses are more forgiving in small variation in the photonic curing conditions, making it more suitable for R2R manufacturing. (3) Our results clearly illustrated the importance of improving mechanical and optical properties of transparent electrodes on flexible substrates. (4) We also performed fundamental studies that elucidate the interactions between perovskite absorber and metal oxide transport layer that can undermine the PSC stability. Five refereed journal papers in top journals (ACS Energy Letters, npj Flexible Electronics, ACS Applied Energy Materials, Materials Advances, and Frontiers in Energy Research), one conference proceeding (PVSC-47), six conference presentations (PVSC and Materials Research Society meetings), and a Ph.D. dissertation (Trey B. Daunis) were produced under this project. Energy Materials Corporation (EMC) has forecast that with a 1.5 m wide web moving at a web speed of 30 m/min, R2R processing of PSC could provide up to 4 GW/year for a single R2R assembly line. Replacing thermal annealing with photonic curing, as demonstrated by the accomplishments of this project, is necessary to realize such an energy production goal.

14 SOLAR ENERGY↗
DOE OSTI2025

Predicting Thermoset Resin Cure Kinetics for Composite Processing

Predicting a material’s thermal properties is not only useful for designing parts but also for defining processing parameters. This is especially applicable to wet-filament winding operations and the production of composite parts using thermoset res ins. For these, the formation of cross-linking bonds is affected by time and temperature, but the degree of cross-linking can be modeled using phenomenological methods. In the current study, the Kissinger and Flynn/Wall/Ozawa methods were both used to calculate kinetic parameters and produced values that were in agreement with each other. The kinetic parameters activation energy ( E a ) and pre-exponential factor (𝐴) calculated from exothermic peak data increased between an epoxy and resole phenol resin system, with a cyanate ester having the highest. The successful application of both methods suggests applicability to future studies for developing cure recipes.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Photonic Curing Enabling High-Speed Processing for Perovskite Solar Cells

The thermal annealing step is the bottleneck to high-throughput manufacturing of perovskite solar cells. In this work, we investigate photonic curing to replace thermal annealing for the sol gel NiO hole transport layer. Using solar cell device current density-voltage performance as a metric, we compare the effects of thermal annealing and photonic curing on the conversion of sol gel NiO films deposited on top of indium tin oxide coated Willow® glass substrates. The significant reduction in processing time validates photonic curing as the enabling tool for high-speed manufacturing.

Xu, Weijie↗
DOE OSTI2022

Design, Processing, and Integration of Pouch-Format Cell for High-Energy Lithium-Sulfur Batteries

This project objective was to develop and demonstrate a lithium-sulfur (Li-S) battery in a pouch-format cell capable of achieving an energy density ≥ 500 Wh/kg while achieving a 1,000 cycle life. The research focused on cell optimization and fabrication addressing different technical barriers and challenges including: 1) thin lithium anode optimization; 2) current collector and tab attachment design; 3) cathode porosity control; 4) electrolyte to sulfur ratio control; 5) cell design; and 6) cell fabrication. The project developed and demonstrated various technologies to address these technical barriers and challenges. The project demonstrated a thin lithium anode by vapor deposition, a collector design and validation of laser welding of tab attachment method, a cathode porosity control strategy by binder optimization, a calendaring process control and surface/interface treatment, and an electrolyte to sulfur ratio control with influence on cell energy density. The sulfur cathode was optimized by tuning the formulation, optimizing the calendaring process, and introducing a novel electrode fabrication process. To address the electrolyte performance issue, the electrolyte optimization was achieved with additive and formulation tuning and the introduction of a dual-phase electrolyte system. In addition to the demonstration of the optimized electrode with a novel fast-curing coating process and dual-phase electrolyte, a coating separator was further developed to address the polysulfide shuttling issue. The resulting new cell design with these optimized cell components was demonstrated in the 1 Ah pouch cell with medium sulfur loading and moderate porosity (~ 4.5 mAh cm-2, 65% porosity) and showed an energy density of > 400 Wh/kg (with E/S ratio of 2.8). The Li-SPAN cell configuration was also evaluated in combination with a new dual-phase electrolyte system. Initial coin cell performance demonstrated cycle stability of >300 cycles with an estimated energy density of 300 Wh/kg at the pouch format level. The corresponding 1 Ah pouch format SPAN cells with the new polymer electrolyte were developed which has shown a stable capacity at 800-900 mAh for ~40 cycles so far.

25 ENERGY STORAGE↗
DOE OSTI2022

Additive manufacturing of nanotube-loaded thermosets via direct ink writing and radio-frequency heating and curing

Direct Ink Writing (DIW) is an extrusion-based additive manufacturing method where the print medium is a liquid-phase ‘ink’ dispensed out of nozzles and deposited along digitally defined paths. Conventional DIW of thermosetting resins relies on viscosity modifying agents, novel crosslinking chemistries, and/or long curing schedules in an oven. Here we demonstrate the use of a co-planar radio frequency applicator to generate an electric field, which can be used to rapidly heat and cure nano-filled composite resins as they are printed. This method avoids the need for an oven or post- curing step. This process consists of a sequential print-and-cure cycle which allows for printing of high-resolution, multi-layered structures. Every extruded layer is partially cured using RF before depositing the next layer; this allows the printed part to maintain structural integrity. The process enables both increased throughput and decreased touch time relative to traditional manufacturing. Commercial epoxy resin with varied nano-filler loadings were examined as DIW candidates. After printing, the thermo-mechanical properties, surface finish, and shape retention of RF-cured samples were comparable to conventionally cured samples. Furthermore, this method of manufacturing establishes RF heating as a suitable alternative to conventional methods, facilitating rapid, free-form processing of thermosetting resins without a mold.

36 MATERIALS SCIENCE↗