Search NASA⌕ Search

SEARCH · Search NASA

Results for “poly-Si contacts”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Controlled Dielectric Breakdown to Form Pinhole Passivated Contacts

This contribution explores a low-temperature route to forming dielectric pinholes to form poly-Si/dielectric/c-Si passivated contacts. The method utilizes controlled dielectric breakdown to form nanoscale pinholes in a thick (non-tunnelling) dielectric which, when annealed, allows dopant atoms to pass from doped poly-Si through the dielectric and into the c-Si wafer forming conductive pathways. We show that the pinholes can be repassivated with dopants and H diffusion which results in increased PL signals after processing. The method can be expanded to optimized dielectric passivation stacks (not just a single layer) and can be formed in parallel over the faces of the wafer in selected areas (only under the grid).

controlled dielectric breakdown↗
DOE OSTI2023

Mitigation of shunt in poly -Si/SiO$_{x}$ passivated interdigitated back contact monocrystalline Si solar cells by self-aligned etching between doped fingers

Polycrystalline silicon on silicon oxide (poly-Si/SiO x ) passivating contacts can be used for ultra-high-efficiency interdigitated back contact (IBC) monocrystalline silicon solar cells. We evaluate the use of intrinsic poly-Si for the region that isolates the p- and n-type fingers at the back side of IBC devices. To mitigate shunt across the isolation region between the doped p- and n-type fingers, we demonstrate self-aligned subtractive processing by etching the poly-Si in the isolation region using SF6 plasma followed by etching in a tetramethylammonium hydroxide (TMAH) solution. After removal of the poly-Si, the isolation region was passivated with SiN x and Al 2 O 3 , which resulted in an 11.7% increase in the fill factor in a 19.8% efficient device. Furthermore, we evaluate the limitations of this device through Suns-V oc analysis and simulations using SunSolve and Quokka3 solar cell simulation software. Through Quokka3, we show that the most significant efficiency losses come from junction recombination current (J 02 ) in the isolation region between doped fingers. We predict that the cell efficiency can be most improved with reduced J 02 through better isolation of heavily doped fingers by etching the isolation region deeper into the bulk or through enhanced surface chemical passivation in this region.

14 SOLAR ENERGY↗
DOE OSTI2022

Dopant Compensation within the Intrinsic Poly-Si Isolation Region in Poly-Si/SiOx Passivated IBC Si Solar Cells

We report on the effect of dopant compensation within intrinsic poly-Si regions between p- and n-type fingers of poly-Si/SiOx passivated interdigitated back contact (IBC) solar cells using intrinsic poly-Si as the isolation region between the doped poly-Si fingers. First, we show that dopants from the doped fingers contaminate the intrinsic gap, resulting in doping of the entire intrinsic gap and overlap of the dopant tails from each finger. Next, we show that despite this doping across the gap, shunting between the doped fingers does not occur. We show that this is a result of trap-assisted compensation creating a highly resistive intrinsic region, preventing shunt. We simulate shunt resistance across the gap based on local carrier concentration and deep trap density. We show that trap defects within the poly-Si enhance compensation between the dopant tails. We experimentally confirm these predictions by scanning spreading resistance microscopy of the gap showing ~20 um domain with resistivity ~10^7 ..omega.. cm. Additionally, Kelvin probe force microscopy are compared to finite element simulations which result in the same approximate shape for potential profile, indicating diode behavior across the isolation region. These results demonstrate the powerful effect that trap defects have within the poly-Si isolation region and suggest that precision patterning is not as essential as once thought.

dopant compensation↗
DOE OSTI2022

Restored Passivation after Complete Removal of Front Poly-Si Between the Grid in Poly-Si/SiO2 Front/Back Cells

This work explores the use of wet chemical etching to completely remove the front poly-Si layer between grid lines of a front/back poly-Si/SiO2 passivated contact device. The purpose of the work is to provide excellent passivation under the metal grid, but to also maximize Jsc by eliminating optical absorption in the front poly-Si. We show that after a high temperature anneal to distribute carriers in the poly-Si/SiO2/c-Si interface all of the poly-Si can be removed selectively with TMAH, using the SiO2 as an etch-stop layer. The etched surface can be repassivated back to its original level with the addition of a SiNx/Al2O3 stack grown on the preserved tunnelling oxide layer followed by a short forming gas anneal. Using symmetric 100 - 200 nm intrinsically doped poly-Si/SiO2 on textured n-type wafer templates we show absolute device efficiency enhancement from 15% to 21% by increasing the Jsc by 12 mA/cm2 after removing the front poly-Si and repassivating while effectively preserving the Voc, and FF of the device. IQE values are similar to PERC devices in the short wavelength range.

etching↗
DOE OSTI2023

Loss Analysis and Performance Optimization Pathways of 729-mV Voc Si Solar Cells with Poly-Si on Locally-Etched Dielectric Passivating Contacts

In this article, the loss analysis of silicon solar cells with polysilicon on locally-etched dielectric passivating contacts with Voc=729.0 mV and efficiency=22.6% has been presented. Experimentally, nano-pinholes were introduced in SiO x (2.2 nm) and SiO x /SiN y (2.2 nm/8nm) stack using metal-assisted chemical etching (MACE). SunSolve and Quokka3 were used to simulate the experimental solar cell and investigate the optical and electrical power losses. Simulations suggest maximum power loss occurs due to recombination and resistive losses in the bulk (~0.76 mW/cm2) followed by power loss due to rear contact recombination (~0.35 mW/cm2). Recombination at the front surface also contributes to 0.24 mW/cm2. The effect of improving the bulk lifetime and lowering the recombination current density at the rear side on Voc, FF and hence, efficiency has been investigated. Further, advanced structures have been proposed to minimize recombination and parasitic absorption to achieve higher Voc and Jsc of the solar cells with locally-etched dielectric passivating contacts.

contacts↗
DOE OSTI2023

Metal-Complex Inks for Lower Cost and Improved Passivation for Silicon Photovoltaic Metallization

This contribution introduces the silicon PV community to screen-printable metal-complex inks that potentially will reduce Ag usage in Si PV metallization to one-quarter and costs to one-third that of traditional particle-based pastes while also improving passivation. Metal-complex inks are formulated using a Tollen's reaction to produce inks with a high percentage of diamminesilver (I) cations (22 wt %) in a solution of acetate and formate anions. When printed and dried labile ammonia ligands evaporate, leaving behind silver cations which, when reduced by formate anions and acetic acid, plate out silver and silver acetate. When annealed to just 300 degrees C a dense metallic silver film forms with excellent conductivity, and adhesion to silicon. When compared to traditional particle-based screen-printing pastes, the metal-complex inks are much denser, have higher conductivity, use less Ag, and are a fraction of the cost. Importantly, the inks anneal from 90 - 450 degrees C allowing for better passivation schemes than fired SiNx. This contribution highlights first experiments on the improved passivation of metallized poly-Si/SiO2 passivated contacts using metal-complex, Ag inks compared with particle-based, fired pastes.

metal-complex ink↗
DOE OSTI2024

Metal-Complex Inks for Lower Cost and Improved Passivation for Silicon Photovoltaic Metallization

This contribution introduces the silicon PV community to screen-printable metal-complex inks that potentially will reduce Ag usage in Si PV metallization to one-quarter and costs to one-third that of traditional particle-based pastes while also improving passivation. Metal-complex inks are formulated using a Tollen’s reaction to produce inks with a high percentage of diamminesilver (I) cations (22 wt %) in a solution of acetate and formate anions. When printed and dried, labile ammonia ligands evaporate, leaving behind silver cations which, when reduced by formate anions and acetic acid, plate out silver and silver acetate. When annealed to just 300 °C a dense metallic silver film forms with excellent conductivity, and adhesion to silicon. When compared to traditional particle-based screen-printing pastes, the metal-complex inks are much denser, have higher conductivity, use less Ag, and are a fraction of the cost. Importantly, the inks anneal from 90 – 450 °C allowing for improved passivation schemes compared with fired SiNx. This contribution highlights first experiments on the improved passivation of metallized poly-Si/SiO2 passivated contacts using metal-complex Ag inks.

Young, David L. (ORCID:0000000340970493)↗
DOE OSTI2024

Investigation of Contact Properties and Device Performance for Bifacial Double-Side Textured Silicon Solar Cells With Polysilicon Based Passivating Contacts

We investigate the impact of the surface morphology on the contact properties of phosphorus doped poly-Si layers. If the poly-Si layer on a textured surface remains intact after high-temperature metallization using a fire-through (FT) silver (Ag) paste, the J0,metal is not expected to increase significantly while the specific contact resistivity can improve with a textured surface. The contact properties of the FT Ag contacts to n+ poly-Si deposited on both textured and planar surfaces are investigated by measuring and evaluating ρc and J0,metal. The reasons for differences in contact resistance and recombination are further investigated with SEM imaging. Solar cells with n-type polysilicon based passivating contacts on the rear side are fabricated and characterized. The scientific approach used, and the insights presented in this work, help to understand the mechanisms and behavior of screen-printed and fired-through contacts to polysilicon layers deposited onto textured silicon surfaces.

Padhamnath, Pradeep (ORCID:0000000202510624)↗
DOE OSTI2023

Pinhole electrical conductivity in polycrystalline Si on locally etched SiN$_y$/SiO$_x$ passivating contacts for Si solar cells

State-of-the-art monocrystalline Si (c-Si) solar cells require passivating contacts to achieve a high degree of charge-carrier separation and collection. In this work, we focus on boron-doped polycrystalline Si on locally etched silicon nitride/silicon oxide (PLENO) passivating contacts. In PLENO contacts, excellent surface passivation is provided by the ~10 nm dielectric bilayer, while pinholes in the dielectric bilayer, that are filled with doped polycrystalline Si, provide charge-carrier selectivity and transport. During PLENO fabrication, etch undercut in the dielectric bilayer occurs. Here, using electrical characterization and microscopies, we show that undercut causes pinholes to be electrically resistive in PLENO. A processing sequence that eliminates the undercut in the final PLENO structure results in electrically conductive pinholes with low contact resistivity.

14 SOLAR ENERGY↗
DOE OSTI2022

Self-Aligned Selective Area Front Contacts on Poly -Si/SiO x Passivating Contact c -Si Solar Cells

We report both polarity poly-Si/SiO x passivating contacts in a front/back device configuration may represent the next solar cell architecture after tunnel oxide passivating contacts (TOPCon) cells, but high parasitic absorption in the front poly -Si layer often limits its performance. This work explores a wet etching technique to remove the front poly -Si in the nonmetallized regions using self-aligned metal grids as an etch mask. We systematically examine various dielectric layers (SiN x ,Al 2 O 3 , and stacks thereof) to study the repassivation of the etched n + surface, and find that an SiN x /Al 2 O 3 passivation stack can effectively repassivate the etched surface, which we attribute to field-effect passivation from the positive fixed charge from the SiN x layer, and excellent chemical passivation property from Al 2 O 3 in the form of atomic H. We demonstrate a front/back poly-Si/SiO x passivating contact device, with an open-circuit voltage (V oc ) of 690 mV, short-circuit current density (J sc ) of 39.8 mA/cm 2 , fill factor of 78%, and power conversion efficiency of 21.4%. Furthermore, simulations using SunSolve and Quokka 3 show good agreement with both the optical and electrical properties of the experimental device. The power loss analysis reveals improvements in the optical loss from the back Ti adhesion and front SiN x layers would lead to a 23.5% device. Lastly, a techno-economic model compares the production cost of this improved cell with the current TOPCon cells. Our results highlight that further cost reductions in single-sided doped poly -Si layers are needed to compete with mainstream passivated emitter and rear cell, and TOPCon technologies.

14 SOLAR ENERGY↗
DOE OSTI2023

Self-Assembled Monolayer Procedure to Pattern Silicon Passivated Contacts

We utilize hexamethyldisilazane (HMDS)-based self-assembled monolayers to pattern polysilicon (polySi) passivated contacts. We find process conditions that allow for etching frontside n/polySi between fingers, thereby increasing Jsc. Importantly, the Voc does not degrade indicating the additional process steps do not introduce defects or impurities. HMDS layers remain on the surface for metallization without detriment to transport.

hexamethyldisilazane↗
DOE OSTI2024

Passivation Mechanisms in Locally Etched P-Type Poly-Si on Silicon Nitride/Silicon Oxide Stack

Tunneling oxide passivated contacts are quickly becoming the industry standard for high-efficiency c-Si based photovoltaic cells. Further development of these structures is essential to enable higher efficiencies and better reliability of cells. By utilizing poly-Si/SixNy/SiOx stacks, very high efficiencies have been demonstrated on small area cells. In this work we investigate the cause of the excellent passivation seen by these structures and show that the primary reason of the excellent passivation seen is the blocking B diffusion to the SiOx/c -Si interface. We also show that the interface between the silicon nitride and polysilicon affects B diffusion through to the c-Si interface. Finally, we demonstrate that the composition of the nitride used is of great importance, and that an incorrect nitride composition leads to B diffusion, and is directly correlated to poor passivation performance.

industries↗
DOE OSTI2022

Development of a co-anneal process for double-side TOPCon precursor fabricated by ex-situ POCI3 and APCVD boron diffusion

The aim of this study was to develop a simple and industrially attractive co-anneal process to fabricate a high-quality DS-TOPCon precursor with textured n-TOPCon on front and planar p- TOPCon on rear by ex-situ POCI3 and APCVD boron diffusion. This requires only one high temperature anneal with no additional masking steps. Excellent iVOC of 733mV and iFF of ~86% were achieved after SiNX passivation on both sides, prior to contact firing. Our device modeling projects that this precursor in combination with a manufacturing-friendly poly-Si patterning technique on front can enable> 25% DS-TOPCon cells at low-cost.

APCVD↗
DOE OSTI2022

Novel Process for Screen-Printed Selective Area Front Polysilicon Contacts for TOPCon Cells Using Laser Oxidation

The efficiency potential of double-side tunnel oxide passivated contact (DS-TOPCon) solar cells is limited by parasitic absorption in the front poly-Si layer, despite excellent passivation and high V OC . The use of patterned poly-Si only under the front metal grid lines can significantly reduce the parasitic absorption loss without sacrificing voltage. In this work, we demonstrate a simple, manufacturing-friendly method of patterning the front poly-Si using a nanosecond UV (355 nm) laser. We found that with laser powers ≥3 W at a 400 mm/s scan speed, an estimated 1–4 nm thick stoichiometric SiO 2 layer was grown on TOPCon. This served as a mask for KOH-etching of 200 nm poly-Si, allowing for patterning of poly-Si fingers required for selective TOPCon. While laser powers above 3 W caused substantial deterioration in passivation quality, the resulting damage in J 0 was largely recovered by subsequent PECVD SiN x deposition. At 3 W, the full area J 0 was found to be 36.8 fA·cm –2 . Furthermore, this translates to 1.68 fA·cm –2 for 4.48% coverage from the wing area of the polyfinger lines (100 lines–100 μm wide and 30 μm metal) contributing to a total front J 0 of ~10 fA·cm –2 , well suited for 25% efficient solar cells

42 ENGINEERING↗
DOE OSTI2023

Detailed investigation of electrical and optical properties of textured n-type and roughened p-type tunnel oxide passivated contacts for screen-printed double-side passivated contact silicon solar cell application

Here, this paper presents detailed characterization and analyses of the optical, electrical, and contact properties of a 35 nm phosphorus-doped (n-type) polysilicon (poly-Si) and a 250 nm boron-doped (p-type) poly-Si deposited respectively on textured and roughed surface. These layers could be applied respectively to the front and rear sides of an n-type Si to produce back junction bifacial screen-printed double-side tunnel oxide passivated contacts (DS-TOPCon) solar cells. Optical and device modeling revealed a short circuit current density loss of 1.5 mA/cm 2 and 0.5 mA/cm 2 due to absorption in the front n-TOPCon and rear side p-TOPCon layers, respectively. The passivation and contact properties including metalized and unmetallized recombination current density (J 0 ), as well as contact resistivity, were determined as a function of contact firing temperature in the range of 700~800°C. The passivation quality of the front thin n-TOPCon was found to deteriorate with increased firing temperature while the rear thick p-TOPCon improved. The study showed that the simulated contact firing at 730°C resulted in the best unmetallized double-side TOPCon precursor, with an excellent implied open-circuit voltage of 730 mV and implied fill factor of ~86 %. However, the metalized J0 increased and contact resistivity decreased monotonically with the increase in the firing temperature. The 2D device simulations revealed that these layers can produce screen-printed DS-TOPCon cells with an efficiency of ~22.5 %. Solar cell modeling also showed that the DS-TOPCon solar cell efficiency can reach 24.1 % by decreasing the n-TOPCon thickness to 20 nm and lowering the full area metalized J 0 to ~100 mA/cm 2 .

14 SOLAR ENERGY↗
DOE OSTI2023

Mechanism of Hydrogen Passivation in Passivated Contact Si Solar Cells

In this abstract, we discuss the mechanism of hydrogen passivation on symmetrical n-Si/ultra-thin SiO2/polySi structures. The hydrogen was introduced from different hydrogen-containing dielectric layers (AlOx:H and SiNx:H and their stacks), as well as by forming gas anneal (FGA). The effusion of hydrogen both from the dielectric layers and in the underlying poly-Si was explored using a quadrupole mass spectrometer (QMS) and FTIR spectroscopy. We show that the strength of hydrogen bonds depend on the deposition technique as well as hydrogenation mechanism. While a PECVD SiNx:H loses hydrogen at a peak temperature of ~450 degrees C, LPCVD SiNx:H, although having less hydrogen compared to PECVD, effuses at a peak temperature of ~850 degrees C. This becomes important to maintain passivation of passivated contacts after firing of metal contacts at high temperatures. On the other hand, it has been observed that SiNx:H provides larger amount of hydrogen to poly-Si after FGA compared to FGA treated AlOx:H, which acts as a capping layer and helps in retaining the hydrogen up to higher temperatures.

hydrogen bonding configuration↗
DOE OSTI2024

Optical Modeling of Polysilicon: TOPCon PV

Determine how film thickness changes with different deposition methods. Analyze relationship between film thickness and optical constants. The deposition rate of intrinsic polysilicon is higher during initial deposition then begins to slow down as deposition time increases. Longer depositions of polysilicon are more crystalline in structure than shorter depositions. N-type doping of polysilicon is more crystalline in structure than p-type doping, despite similar film thicknesses.

Bruggeman effective media approximation↗
DOE OSTI2022

Characterization of Engineered Pinholes in Dielectric Stacks of High-Performance Poly-Silicon Passivating Contacts

Passivating contact structures are expected to be implemented in > 50 % of industrially manufactured silicon photovoltaics produced over the next decade. One type of passivating contact utilizes a c-Si/dielectric/doped poly-Si layer stack. In cases where the dielectric layer/s are thick enough to impede tunneling of charge carriers, it was shown that disruptions (pinholes) in the dielectric are required to facilitate transport.[1] Pinholes in SiOx layers have typically been formed via high temperature annealing that allows localized breakup of this layer. This approach has drawbacks; 1) high temperature annealing increases cost and 2) pinhole formation is sensitive to both the SiOx thickness and wafer surface morphology making control of density and dimensions difficult. Recently, an alternative method of pinhole formation relying on metal assisted chemical etching (MACE) was shown to allow control over pinhole areal densities.[2] Such control is critical as both the density and dimensions of the pinholes determine saturation current density and contact resistivity. The contacts formed with the MACE process are known as polysilicon on locally etched oxide or PLEO and also result in low saturation current densities and low contact resistivity due to SiOx passivation and engineered pinhole enabled charge carrier transport, respectively. Photovoltaic devices with efficiencies greater than 20 % have recently been produced with these contacts, demonstrating the viability of contacts with engineered pinholes. Experimentally, preferential local collection of excess charge carriers has been observed and definitively connected to thermally induced pinholes in thick SiOx layers within c-Si/SiOx/poly-Si contact structures.[3] Recent work has shown that enhanced local collection of excess carriers can result from enhanced diffusion of dopants through pinholes in SiOx layers.[4] This study was restricted to simulation and characterization of poly-Si with the same dopant type as the c-Si substrates. In this work we focus our analysis on boron doped poly-Si with different stacks of dielectric layers (PLEO and PLENO where the N refers to a SiNy layer on top of the SiOx) on n-type crystalline silicon. This provides insight into how engineered pinholes affect charge collection across the p-n junction. Like previous observations of locally enhanced carrier transport through thermally induced pinholes, the EBIC images in Figure 1 shows that engineered pinholes in PLENO (1a) and PLEO (1b) also exhibit locally enhanced carrier transport at pinhole locations (bright spots in the images). We will also present detailed correlative nanoscale structural and chemical analysis using TEM imaging and EELS analysis with sample preparation guided by EBIC imaging. This allows us to connect the density and dimensions of engineered pinholes with charge carrier transport and measured photovoltaic device parameters. Our findings will accelerate the adoption of PLEO and PLENO contacts in industrially manufactured photovoltaic devices.

EBIC↗