Search NASA⌕ Search

SEARCH · Search NASA

Results for “ROLLING ELEMENT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37

Quantification of complex-phase steel microstructure by using combined EBSD and EPMA measurements

Highlights: • In CP800 steel, bainite is the dominant phase with a typical lath (width 300 nm) structure and cementite precipitates. • Martensite is dispersed as small islands and only a few narrowed martensite bands are observed which has been induced by annealing process of cold rolled sheet. • The precise carbon content is measured in bainite and martensite utilizing EPMA line scans, which is around 0.2 wt% and 0.4 wt%, respectively. • Digitalization of the microstructure for CP800 is achieved by combining EBSD and EPMA techniques. • The final constituent map consists of plenty of microstructural features including topography, crystal structures, orientations and elemental distribution. - Abstract: We combined electron backscatter diffraction (EBSD) and electron probe microanalysis (EPMA) techniques to characterize the microstructure of industrial produced complex-phase CP800 steel. First, three major constituents (ferrite, martensite and bainite) are characterized. Then, transformation-induced dislocation zones in ferrite and bainitic regions consisting of different sub-structures are quantified and segmented. A final digitalized component map including plenty of microstructural features including crystal structures, orientations and elemental distribution are successfully achieved. The precise carbon content is measured in bainite and martensite utilizing EPMA line scans, which is around 0.2 wt% and 0.4 wt%, respectively. In the bainite phase of CP800, a typical Bagaryatski orientation relationship between cementite and lath-like bainitic ferrite is revealed based on the select diffraction patterns of transmission electron microscopy measurements.

36 MATERIALS SCIENCE↗

Isothermal elastohydrodynamic lubrication of point contacts. I - Theoretical formulation

The analysis of an isothermal elastohydrodynamic lubrication (EHL) point contact was evaluated numerically. This required the simultaneous solution of the elasticity and Reynolds equations. In the elasticity analysis the contact zone is divided into equal rectangular areas and it is assumed that a uniform pressure is applied over each element. In the numerical analysis of the Reynolds' equation a phi analysis where phi is equal to the pressure times the film thickness to the 3/2 power is used to help the relaxation process. The EHL point contact analysis is applicable for the entire range of elliptical parameters and is valid for any combination of rolling and sliding within the contact.

Hamrock, B. J.↗

Use of Monocrystalline Silicon as Tool Material for Highly Accurate Blanking of Thin Metal Foils

The trend towards miniaturisation of metallic mass production components combined with increased component functionality is still unbroken. Manufacturing these components by forming and blanking offers economical and ecological advantages combined with the needed accuracy. The complexity of producing tools with geometries below 50 {mu}m by conventional manufacturing methods becomes disproportional higher. Expensive serial finishing operations are required to achieve an adequate surface roughness combined with accurate geometry details. A novel approach for producing such tools is the use of advanced etching technologies for monocrystalline silicon that are well-established in the microsystems technology. High-precision vertical geometries with a width down to 5 {mu}m are possible. The present study shows a novel concept using this potential for the blanking of thin copper foils with monocrystallline silicon as a tool material. A self-contained machine-tool with compact outer dimensions was designed to avoid tensile stresses in the brittle silicon punch by an accurate, careful alignment of the punch, die and metal foil. A microscopic analysis of the monocrystalline silicon punch shows appropriate properties regarding flank angle, edge geometry and surface quality for the blanking process. Using a monocrystalline silicon punch with a width of 70 {mu}m blanking experiments on as-rolled copper foils with a thickness of 20 {mu}m demonstrate the general applicability of this material for micro production processes.

36 MATERIALS SCIENCE↗

Study of slip activity in a Mg-Y alloy by in situ high energy X-ray diffraction microscopy and elastic viscoplastic self-consistent modeling

Slip activity from various slip modes largely determines the yield strength and ductility of Mg alloys. Solid solution elements in Mg can change the slip activity dramatically. In this paper, far-field high energy X-ray diffraction microscopy (FF-HEDM) is employed to study slip activity in a Mg-3wt%Y alloy during an in situ tensile experiment. The specimen was incrementally loaded up to 3% engineering strain along the rolling direction. At each load step, FF-HEDM data were collected to track the crystallographic orientation, center of mass, and stress tensor changes of nearly 1000 grains in the probed volume. By analyzing the change in orientation and stress tensor of individual grains at different load steps, it is possible to identify the activated slip systems and measure their critical resolved shear stress (CRSS) values. Prismatic slip and pyramidal I slip are found to be very active in this alloy. The estimated CRSS values for basal slip, prismatic slip and pyramidal I slip are 12 MPa, 38 MPa, and 36 MPa, respectively. These CRSS values were applied in a dislocation-based elastic viscoplastic self-consistent (EVPSC) model that successfully simulated the tensile stress-strain curve from the FF-HEDM experiment. The model also qualitatively predicted the crystal rotation in most of the selected grains, though it underestimated the internal stress and the magnitude of crystal rotation in these grains. Influence of solute Y on the strength and ductility of Mg alloys is discussed.

36 MATERIALS SCIENCE↗

Nano-twin Mediated Plasticity in Carbon-containing FeNiCoCrMn High Entropy Alloys

Equiatomic FeNiCoCrMn alloy has been reported to exhibit promising strength and ductility at cryogenic temperature and deformation mediated by nano-twining appeared to be one of the main reasons. We use the FeNiCoCrMn alloy as a base alloy to seek further improvement of its mechanical properties by alloying additional elements, i.e., interstitial carbon. Moreover, the effects of carbon on microstructures, mechanical properties and twinning activities were investigated in two different temperatures (77 and 293 K). With addition of 0.5 at% C, the high entropy alloy still remains entirely single phase face-centered cubic (FCC) crystal structure. We found that these materials can be cold rolled and recrystallized to produce a microstructure with equiaxed grains. Both strain hardening rate and strength are enhanced while high uniform elongations to fracture (~70% at 77 K and ~40% at 293 K) are still maintained. The increased strain hardening and strength could be caused by the promptness of deformation twinning in C-containing high entropy alloys.

36 MATERIALS SCIENCE↗

New Tools Being Developed for Engine- Airframe Blade-Out Structural Simulations

One of the primary concerns of aircraft structure designers is the accurate simulation of the blade-out event. This is required for the aircraft to pass Federal Aviation Administration (FAA) certification and to ensure that the aircraft is safe for operation. Typically, the most severe blade-out occurs when a first-stage fan blade in a high-bypass gas turbine engine is released. Structural loading results from both the impact of the blade onto the containment ring and the subsequent instantaneous unbalance of the rotating components. Reliable simulations of blade-out are required to ensure structural integrity during flight as well as to guarantee successful blade-out certification testing. The loads generated by these analyses are critical to the design teams for several components of the airplane structures including the engine, nacelle, strut, and wing, as well as the aircraft fuselage. Currently, a collection of simulation tools is used for aircraft structural design. Detailed high-fidelity simulation tools are used to capture the structural loads resulting from blade loss, and then these loads are used as input into an overall system model that includes complete structural models of both the engines and the airframe. The detailed simulation (shown in the figure) includes the time-dependent trajectory of the lost blade and its interactions with the containment structure, and the system simulation includes the lost blade loadings and the interactions between the rotating turbomachinery and the remaining aircraft structural components. General-purpose finite element structural analysis codes are typically used, and special provisions are made to include transient effects from the blade loss and rotational effects resulting from the engine s turbomachinery. To develop and validate these new tools with test data, the NASA Glenn Research Center has teamed with GE Aircraft Engines, Pratt & Whitney, Boeing Commercial Aircraft, Rolls-Royce, and MSC.Software.

Lawrence, Charles↗

Liquid-metal atomization for hot working preforms

Rapid quenching of a liquid metal by atomization or splat cooling overcomes the major limitation of most solidification processes, namely, the segregation of alloying elements, impurities, and constituent phases. The cooling rates of different atomizing processes are related to the dendrite arm spacings and to the microstructure of the atomized powders. The increased solubility limits and the formation of metastable compounds in splat-cooled alloys are discussed. Consolidation of the powders by hot isostatic compaction, hot extrusion, or hot forging and rolling processes yields billets with properties equivalent to or better than those of the wrought alloys. The application of this powder processing technology to high-performance alloys is reviewed.

Grant, N. J.↗

Lubrication of nonconformal contacts

Minimum film thickness results for piezoviscous-rigid regime of lubrication are developed for a compressible Newtonian fluid with Roelands viscosity. The results provide a basis for the analysis and design of a wide range of machine elements operating in the piezoviscous-rigid regime of lubrication. A new numerical method of calculating elastic deformation in contact stresses is developed using a biquadratic polynomial to approximate the pressure distribution on the whole domain analyzed. The deformation of every node is expressed as a linear combination of the nodal pressures whose coefficients can be combined into an influence coefficient matrix. This approach has the advantages of improved numerical accuracy, less computing time and smaller storage size required for influence matrix. The ideal elastohydrodynamic lubrication is extended to real bearing systems in order to gain an understanding of failure mechanisms in machine elements. The improved elastic deformation calculation is successfully incorporated into the EHL numerical scheme. Using this revised numerical technique and the flow factor model developed by Patir and Cheng (1978) the surface roughness effects on the elastohydrodynamic lubrication of point contact is considered. Conditions typical of an EHL contact in the piezoviscous-elastic regime entrained in pure rolling are investigated. Results are compared with the smooth surface solutions. Experiments are conducted to study the transient EHL effects in instrument ball bearings.

Jeng, Y. R.↗

Self-Deployable Spring-Strip Booms

Booms and other structures consisting mainly of thin spring strips are undergoing development. These structures are designed to be lightweight, to be compactly stowable, and to be capable of springing to stable configurations at full extension once released from stowage. Conceived for use as self-deploying structures in outer space, portable structures of this type may also be useful on Earth in applications in which there are requirements for light weight and small transportation volume. The elements common to these structures are spring strips with curved cross sections -- similar to spring strips of the type commonly used as compactly stowable carpenters' measuring tapes. These structures exploit the nonlinear mechanical properties of such tapes, namely (1) strong resistance to axial buckling while they are straight and (2) ease with which they can be wound into compact rolls once they have been initially bent. For a structure that contains multiple such strips, the net effect of the combined nonlinear characteristics is the following: (1) When at full extension, the structure is in a stable state, in which it is rigid and strong. (2) When stowed compactly, the structure is in a state that is semistable in the sense that only a small force is needed to restrain the structure against deployment. (3) The strain energy stored in the spring strips during compaction is sufficient to deploy the structure to full extension when the restraint is removed.

Fang, Houfei↗

Reverse martensitic transformation on the corrosion behavior of a 2304 lean duplex stainless steel

This study investigates the influence of the reverse martensitic transformation on the corrosion behavior of 2304 lean duplex stainless steel (LDSS) at low temperatures (400–600°C). The steel underwent cold rolling, followed by isochronal annealing for 0.5 h. Phase transformations and microstructures were analyzed using X-ray diffraction, scanning electron microscopy, and transmission electron microscopy. Corrosion resistance was evaluated using a syringe cell with cyclic potentiodynamic polarization in 0.6 M NaCl solution and double-loop electrochemical potentiokinetic reactivation in 0.5 M H 2 SO 4 + 0.001 M KSCN solution. A bimodal breakdown potential behavior, associated with either pitting or transpassivity, was observed in the as-received (AR) and samples annealed at 400°C. Pitting in the AR sample was associated with Al–Mg–Si–Ca–O inclusions, while pitting on the samples annealed at 400°C was linked to local reduced passive film resistance. Severe cold rolling enhanced the pitting resistance of 2304 LDSS. Selective electrochemical etching revealed preferential corrosion at phase interfaces and within the austenite phase. Additionally, annealing at 500°C to 600°C led to a marked decrease in pitting resistance and increased sensitization. Electron backscatter diffraction analysis of the corroded pits in the annealed specimens indicated that pits tend to nucleate and grow in α'-martensite/austenite regions. Furthermore, the nanostructure formed during low-temperature reversion, characterized by dislocation-cell martensite with high dislocation density and stacking faults, may adversely affect corrosion resistance due to heterogeneities associated with alloying element redistribution.

36 MATERIALS SCIENCE↗

FY2022 Progress Report on Viscosity and Thermal Conductivity Measurements of Molten Salts

This report describes the development of and experimental measurements made with the thermal conductivity and viscosity measurement systems for molten salts at Oak Ridge National Laboratory. The thermal conductivity system is based on a steady-state measurement technique in which a heat flux is driven across a variable gap, and the changes in temperature difference across the gap are measured as the gap size is varied. The system comprises an inner containment, which possesses the heating element, and an outer containment, which possesses the salt specimen and cooling channels. The gap is formed between the outer bottom of the inner containment and the inner bottom of the outer containment. The viscosity system is based on the falling-ball technique in which a salt-filled tubular crucible is fixed at an angle and a ball rolls through the salt. The terminal velocity of the ball can be converted into viscosity via a calibration factor calculated for crucible-ball combinations which account for thermal expansion and flow characteristics. Modifications were made to both systems this fiscal year. Modifications to the thermal conductivity system included adding guard heaters to prevent axial heating losses, and modifications to the viscosity system included changing the crucible design to prevent air pocket formation and providing the ability to conduct measurements with a glass or steel crucible.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Reducing the Cost of Solar Cells

Solar-powered electricity prices could soon approach those of power from coal or natural gas thanks to collaborative research with solar startup Ampulse Corporation at the National Renewable Energy Laboratory. Silicon wafers account for almost half the cost of today's solar photovoltaic panels, so reducing or eliminating wafer costs is essential to bringing prices down. Current crystalline silicon technology converts energy in a highly efficient manner; however, that technology is manufactured with processes that could stand some improvement. The industry needs a method that is less complex, creates less waste and uses less energy. First, half the refined silicon is lost as dust in the wafer-sawing process, driving module costs higher. Wafers are sawn off of large cylindrical ingots, or boules, of silicon. A typical 2-meter boule loses as many as 6,000 potential wafers during sawing. Second, the wafers produced are much thicker than necessary. To efficiently convert sunlight into electricity, the wafers need be only one-tenth the typical thickness. NREL, the Oak Ridge National Laboratory and Ampulse have partnered on an approach to eliminate this waste and dramatically lower the cost of the finished solar panels. By using a chemical vapor deposition process to grow the silicon on inexpensive foil, Ampulse is able to make the solar cells just thick enough to convert most of the solar energy into electricity. No more sawdust - and no more wasting refined silicon materials. NREL developed the technology to grow high-quality silicon and ORNL developed the metal foil that has the correct crystal structure to support that growth. Ampulse is installing a pilot manufacturing line in NREL's Process Development Integration Laboratory, where solar companies can work closely with lab scientists on integrated equipment to answer pressing questions related to their technology development, as well as rapidly overcoming R and D challenges and risk. NREL's program is focused on transformative innovation in the domestic PV industry. With knowledge and expertise acquired from the PDIL pilot production line tools, Ampulse plans to design a full-scale production line to accommodate long rolls of metal foil. The Ampulse process 'goes straight from pure silicon-containing gas to high-quality crystal silicon film,' said Brent Nelson, the operational manager for the Process Development Integration Laboratory. 'The advantage is you can make the wafer just as thin as you need it - 10 microns or less.' Most of today's solar cells are made out of wafer crystalline silicon, though thin-film cells made of more exotic elements such as copper, indium, gallium, arsenic, cadmium, tellurium and others are making a strong push into the market. The advantage of silicon is its abundance, because it is derived from sand. Silicon's disadvantage is that purifying it into wafers suitable for solar cells can be expensive and energy intensive. Manufacturers add carbon and heat to sand to produce metallurgical-grade silicon, which is useful in other industries, but not yet suitable for making solar cells. So this metallurgical-grade silicon is then converted to pure trichlorosilane (SiCl3) or silane (SiH4) gas. Typically, the purified gas is then converted to create a silicon feedstock at 1,000 degrees Celsius. This feedstock is melted at 1,414 C and recrystallized into crystal ingots that are finally sawed into wafers. The Ampulse method differs in that it eliminates the last two steps in the traditional process and works directly with the silane gas growing only the needed silicon right onto a foil substrate. A team of NREL scientists had developed a way to use a process called hot-wire chemical vapor deposition to thicken silicon wafers with near perfect crystal structure. Using a hot tungsten filament much like the one found in an incandescent light bulb, the silane gas molecules are broken apart and deposited onto the wafer using the chemical vapor deposition technique at about 700 C - a much lower temperature than needed to make the wafer. The hot filament decomposes the gas, allowing silicon layers to deposit directly onto the substrate. Armed with this new technique, Branz and Teplin searched for ways to grow the silicon on cheaper materials and still use it for solar cells. They found the ideal synergy when visiting venture capitalists from Battelle Ventures asked them whether they could do anything useful with a breakthrough from Oak Ridge's superconducting wire development group. The new development, called the rolling assisted biaxially textured substrate (RABiTS), was just the opportunity the two scientists had been seeking. If metal foil is to work as a substrate, it must be able to act as a seed crystal so the silicon can grow on it with the correct structure. The RABiTS process forms crystals in the foil that are correctly oriented to receive the silicon atoms and lock them into just the right positions.

14 SOLAR ENERGY↗

Discovery, Design, Synthesis and Testing of High Performance Structural Alloys (Final Technical Report)

The overarching goal of this project is to understand the phase stability and mechanical behavior of non-stoichiometric multi-principal element alloy (MPEA) materials. In order to identify suitable alloys, we plan to use a combinatorial thin film screening approach, in collaboration with scientists at Lawrence Berkeley National Laboratory who are performing computational work as well as complementary experimental work. Specific tasks within the scope of this project include the fabrication, using thin film deposition from six sputtering targets, of combinatorial samples with multi-dimensional gradients in composition and microstructure. These samples are studied to screen MPEA systems for promising candidate alloys with specific composition(s), based on characterization of composition, structure and mechanical behavior across the thin film. We want to produce single-phase MPEAs with chemical homogeneity in a given thin film region, simple grain structures, and no intermetallic phases present. Gradient films facilitate first-pass screening for desirable characteristics and inform the next stage of work that involves fabrication of bulk MPEA specimens for (tensile) mechanical testing and characterization. To make the bulk alloys, metal (elemental) pieces are melted to form MPEAs, followed by heat treatment to homogenize the composition and microstructure. A subset of alloys is also cast, using vacuum arc melting, to yield larger samples (diameter ~1 cm and length ~5-10 cm) and these allow us to assess viability of scale-up for the alloys in structural applications. Further processing plans include rolling and heat treatment to recrystallize selected bulk MPEAs and grow grains to different extents, in order to investigate size effects in the mechanical behavior of MPEAs. Microspecimen testing will be performed (primarily in tension) to assess the mechanical behavior over a range of temperatures. The deformation microstructure of mechanically tested alloys will be characterized using transmission electron microscopy (TEM) to provide a scientific basis for understanding the structure-property relationships in MPEA mechanical behavior.

36 MATERIALS SCIENCE↗

ATS-6 - Interferometer

The ATS-6 interferometer provides precision, 3-axis attitude sensing capability. It incorporates a C-band receiver which measures the phase difference of continuous ground station signals received at paired antenna elements and converts this phase difference into digital data that is transmitted to the ground, and is also used as direct input to the onboard digital operations controller for conversion to attitude information. It uses 6 onboard horn antennas, placed in the earth viewing module, with three antennas arranged along each of two orthogonal baselines parallel to the satellite pitch and roll axes, one antenna used as a measurement reference on each baseline, and the remaining two horns, placed to provide phase measurements relative to the respective reference antenna.

Isley, W. C.↗

Designing the L-1011 to minimize rotor failures effects

Design philosophies used in the L-1011 aircraft to provide protection against rotor fragments include: (1) incorporating into the rotor design features that tend to promote small fragments if failure occurs; (2) containing the fragments within the engine shell or greatly reducing the energy content of those fragments that are eventually uncontained; (3) shielding vulnerable elements or systems with heavy structural members that tend to stop or deflect high velocity fragments; and (4) incorporating redundant and/or backup systems into the basic design and separating these systems so as to minimize the probability that more than one system will be damaged by an uncontained rotor fragment. Some of the design features that were incorporated into the Rolls-Royce RB211 engine are discussed, and two in-service experiences are considered in order to illustrate the practical operation of these features.

Wignot, J. E.↗

The potential for crustal resources on Mars

Martian resources pose not only an interesting scientific challenge but also have immense astronautical significance because of their ability to enhance mission efficiency, lower launch and program costs, and stimulate the development of large Mars surface facilities. Although much terrestrial mineralization is associated with plate tectonics and Mars apparently possesses a thick, stationary lithosphere, the presence of crustal swells, rifting, volcanism, and abundant volatiles indicates that a number of sedimentary, hydrothermal, dry-magma mineral concentration processes may have operated on Mars. For example, in Colorado Plateau-style (roll-front) deposits, uranium precipitation is localized by redox variations in groundwater. Also, evaporites (either in salt pans or even interstitially in pore spaces) might concentrate Cl, Li, and K. Many Martian impact craters have been modified by volcanism and probably have been affected by rising magma bodies interacting with ground ice or water. Such conditions might produce hydrothermal circulations and element concentrations. If the high sulfur content found by the Viking landers typifies Martian abundances, sulfide ore bodies may have been formed locally. Mineral-rich Africa seems to share many volcanic and tectonic characteristics with portions of Mars and may suggest Mars' potential mineral wealth. For example, the rifts of Valles Marineris are similar to the rifts in east Africa, and may both result from a large mantle plume rising from the interior and disrupting the surface. The gigantic Bushveld complex of South Africa, an ancient layered igneous intrusion that contains ores of chromium and Pt-group metals, illustrates the sort of dry-magma processes that also could have formed local element concentrations on Mars, especially early in the planet's history when heat flow was higher.

Cordell, Bruce M.↗

Active Site Sharing and Subterminal Hairpin Recognition in a New Class of DNA Transposases

Many bacteria harbor simple transposable elements termed insertion sequences (IS). In Helicobacter pylori, the chimeric IS605 family elements are particularly interesting due to their proximity to genes encoding gastric epithelial invasion factors. Protein sequences of IS605 transposases do not bear the hallmarks of other well-characterized transposases. We have solved the crystal structure of full-length transposase (TnpA) of a representative member, ISHp608. Structurally, TnpA does not resemble any characterized transposase; rather, it is related to rolling circle replication (RCR) proteins. Consistent with RCR, Mg{sup 2+} and a conserved tyrosine, Tyr127, are essential for DNA nicking and the formation of a covalent intermediate between TnpA and DNA. TnpA is dimeric, contains two shared active sites, and binds two DNA stem loops representing the conserved inverted repeats near each end of ISHp608. The cocrystal structure with stem-loop DNA illustrates how this family of transposases specifically recognizes and pairs ends, necessary steps during transposition.

36 MATERIALS SCIENCE↗

Static and dynamic force/moment measurements in the Eidetics water tunnel

Water tunnels have been utilized in one form or another to explore fluid mechanics and aerodynamics phenomena since the days of Leonardo da Vinci. Water tunnel testing is attractive because of the relatively low cost and quick turn-around time to perform flow visualization experiments and evaluate the results. The principal limitation of a water tunnel is that the low flow speed, which provides for detailed visualization, also results in very small hydrodynamic (aerodynamic) forces on the model, which, in the past, have proven to be difficult to measure accurately. However, the advent of semi-conductor strain gage technology and devices associated with data acquisition such as low-noise amplifiers, electronic filters, and digital recording have made accurate measurements of very low strain levels feasible. The principal objective of this research effort was to develop a multi-component strain gage balance to measure forces and moments on models tested in flow visualization water tunnels. A balance was designed that allows measuring normal and side forces, and pitching, yawing and rolling moments (no axial force). The balance mounts internally in the model and is used in a manner typical of wind tunnel balances. The key differences between a water tunnel balance and a wind tunnel balance are the requirement for very high sensitivity since the loads are very low (typical normal force is 0.2 lbs), the need for water proofing the gage elements, and the small size required to fit into typical water tunnel models.

Carlos J Suarez↗