Search NASA⌕ Search

SEARCH · Search NASA

Results for “Solid oxide electrolysis cell (SOEC)”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Image processing workflow yielding high contrast synchrotron nanoscale computed tomography data from Ni-YSZ electrodes

The operating lifetime of Ni-YSZ fuel electrodes used in solid oxide electrolysis cells and fuel cells (SOECs and SOFCs) is limited by Ni redistribution, one of the primary degradation mechanisms that must be overcome to extend the longevity and maximize the performance of SOECs and SOFCs. To achieve this, 3D microstructural data is needed to relate both initial performance and performance loss over time to microstructural properties and their evolution throughout operation under various conditions. However, 3D microstructure data remains relatively scarce within the literature due to multiple challenges in acquiring and analyzing such data reliably. This work presents a workflow for acquiring and processing synchrotron X-ray nanoscale computed tomography (nano-CT) data from Ni-YSZ electrodes. Parameters for each step in the nano-CT workflow are described up to the final result (a 3D reconstruction), with particular emphasis on image alignment using freely available software. Following the results of a parametric sweep of the image alignment step, high contrast, low signal-to-noise 3D nano-CT data is obtained with relatively short compute times. While the exact methods best suited to samples with different microstructural qualities, or similar Ni-YSZ nano-CT data obtained from other sources may deviate from the solution found herein, this work also generalizes the decision points and evaluation of each step to provide a starting point to adapt this workflow to other datasets.

08 HYDROGEN↗
DOE OSTI2020

Progress in metal-supported solid oxide electrolysis cells: A review

There is increasing global interest in using solid oxide electrochemical cells to perform electrolysis. Metal-supported solid oxide electrolysis cells (MS-SOEC) are being developed with stainless steel and Ni-based supports. Additionally, the use of porous metal to support the electrochemically-active layers is anticipated to improve mechanical strength, decrease cost, and increase tolerance to aggressive operating conditions, including rapid thermal excursions. This review summarizes and analyzes the previous decade of progress in MS-SOEC development, and identifies critical needs for future work.

08 HYDROGEN↗
DOE OSTI2023

Oxidation of porous stainless steel supports for metal-supported solid oxide electrolysis cells

Oxidation behavior of porous P434L ferritic stainless steel, used for the fabrication of metal-supported solid oxide electrolysis cells (MS-SOEC), is studied under oxygen-side and steam-side conditions. The impact of oxygen content on the oxygen side and steam:hydrogen ratio on the steam side is determined at 700°C for bare, as-sintered samples. For these conditions, oxidation is more aggressive in the steam-side atmosphere. Oxygen with 3% humidification and steam:hydrogen ratio of 90:10 are selected for further assessment with pre-oxidized, catalyst-coated, and CuMn1·8O4-coated samples. The rapid oxidation at 700°C and breakaway oxidation at 600 °C observed for bare stainless steel in 90:10 steam:hydrogen is mitigated by pre-oxidizing the sample in air before exposure. In oxygen, addition of the catalyst or CuMn 1·8 O 4 coatings moderately increases the oxidation rate, due to consumption of Cr via reaction between the coatings and Cr-oxide scale. In conclusion, the results for ex-situ controlled oxidation are similar to oxidation observed after 1000h operation of a full MS-SOEC. In general, the oxidation behavior at 700°C is found to be acceptable.

08 HYDROGEN↗
DOE OSTI2023

Optimization of metal-supported solid oxide electrolysis cells with infiltrated catalysts

We report metal-supported solid oxide electrolysis cells (MS-SOECs) are being developed for steam-to-hydrogen electrolysis, especially for utilization of dynamic or intermittent electrical power from renewable sources. Various aspects of the electrocatalyst processing and composition, and metal support structure were explored. Catalyst materials, infiltration temperature and infiltration cycles were optimized for high performance and durability. Numerous catalyst materials were screened for both oxygen and steam electrodes. The oxygen catalyst had moderate impact on both initial cell performance and durability. Reducing Ni content in the steam electrode had little effect on durability, but reduced initial performance. Ex-situ XRD analysis and cell assessment of catalyst infiltration temperature revealed that the optimal range is 750–850 °C. The best cell performance and durability was achieved with LSCF-SDC oxygen electrocatalyst and SDC-Ni (60:40 vol%) steam electrocatalyst infiltrated 11 times at 800 °C and operated at 700 °C. At low steam content, a significant mass transport limitation on the steam side results in limiting current behavior. Thinner and more porous metal supports were implemented, and found to improve steam mass transport at low steam content, relevant for SOECs operating under high H 2 recycle rate or high steam utilization.

08 HYDROGEN↗
DOE OSTI2023

Improving the performance for direct electrolysis of CO 2 in solid oxide electrolysis cells with a Sr 1.9 Fe 1.5 Mo 0.5 O 6– δ electrode via infiltration of Pr 6 O 11 nanoparticles

Direct CO 2 electrolysis using solid oxide electrolysis cells (CO 2 -SOECs) holds promise to efficiently convert carbon dioxide to carbon monoxide and oxygen. Cathodes with desirable catalytic activity and chemical stability play a critical role in the development of direct CO 2 -SOECs. Although Sr 2 Fe 1.5 Mo 0.5 O 6–δ (SFM) has exhibited promise for direct CO 2 -SOECs due to its redox stability, it suffers from insufficient activity for the CO 2 reduction reaction (CO 2 RR). Here we report interface engineering of nanosized Pr 6 O 11 on the SFM cathode obtained through infiltration to promote the CO 2 RR performance for direct CO 2 -SOECs. The effect of Pr 6 O 11 loading on the performance of the CO 2 RR is systematically investigated. At 800 °C, the current density of the Pr 6 O 11 infiltrated SFM cathode with an optimum Pr 6 O 11 loading of 14.8 wt% reaches 1.61 A cm –2 at 1.5 V, more than double that of the SFM cathode (0.76 A cm –2 ) under the same operating conditions. X-ray photoelectron spectroscopy (XPS) characterization and in situ diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) analysis indicate that the adsorption ability of CO 2 on the SFM cathode has been significantly improved by the formation of Pr 6 O 11 . Temperature-programmed desorption (TPD) of CO 2 measurements further manifest that a 14.8 wt% Pr 6 O 11 -SFM cathode has better CO desorption capacity. In addition, polarization resistance of the SFM cathode has significantly decreased with the addition of Pr 6 O 11 . Three-electrode measurement was used to analyze the improved electrode kinetics. Finally, these results demonstrate that the formation of Pr 6 O 11 in the SFM cathode through infiltration is a promising approach for increasing CO 2 RR activity for CO 2 -SOECs.

03 NATURAL GAS↗
DOE OSTI2024

Dynamic operation of metal-supported solid oxide electrolysis cells

Symmetric-structure metal-supported solid oxide fuel cells and electrolysis cells (MS-SOFCs, MS-SOECs) offer several advantages over conventional solid oxide cells, including the use of inexpensive materials, high mechanical strength, and rapid ramp-up ability. Aggressive operation of MS-SOCs in fuel cell mode is well-established, including extremely fast start-up, redox tolerance, and imbalanced pressure. Here, we extend dynamic operation to MS-SOCs in SOEC mode with high steam content for both small button cells and a large rectangular cell, including: steam cycling, thermal cycling, redox cycling and power cycling. Steam cycling entailed switching between 3:97 and 50:50 steam:hydrogen ratio. For thermal cycling, the temperature was rapidly varied between 150°C and 700°C for 50 cycles. Redox cycling involved switching the steam side gas between 50 % humidified H 2 and 50 % humidified N 2 for 5 cycles. Power cycling was performed by operating the cell under variable current density, resulting in cell voltage between 1.3V and 2.8V. Degradation rates for each testing strategy were compared to a baseline cell, and found to be similar. In conclusion, the excellent tolerance to dynamic operation increases confidence that MS-SOECs will be compatible with dynamic or intermittent renewable resources.

08 HYDROGEN↗
DOE OSTI2026

Robust dynamic operation of high temperature electrolysis solid oxide cells

Here, this study evaluates the durability of Ni/YSZ-supported SOECs under dynamic operating conditions relevant to real-world applications. Systematic tests were conducted to assess cell performance under steam cycling (3 to 75% humidified H 2 ), mode cycling between SOFC and SOEC operation, thermal cycling (150 to 750 °C at OCV, and 600 to 800 °C at 1.3V), and redox cycling (between 50% humidified H 2 and 50% humidified N 2 ). Steam cycling, mode cycling, and thermal cycling at OCV do not significantly accelerate performance degradation. Thermal cycling at 1.3V caused minimal damage within 600 to 800 °C. Full redox cycling (multi-hour oxidation holds) induced cell structural failure, while partial redox cycling (0.5 h holds) was tolerated. Extensive characterization revealed some material evolution, namely Sr and Co secondary phase formation, within the oxygen electrode due to La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3-δ instability, especially for steam cycling and mode cycling. Minimal changes were identified within the Ni-YSZ fuel electrodes. These findings provide critical insights into SOEC reliability under dynamic conditions, supporting their application in dynamic or intermittent energy systems.

08 HYDROGEN↗
DOE OSTI2023

Challenges in practical button cell testing for hydrogen production from high temperature electrolysis of water

High temperature electrolysis of water using solid oxide electrochemical cells (SOEC) is a promising technology for hydrogen production with high energy efficiency and may promote decarbonization when coupled with renewable energy sources and excess heat from nuclear reactors. Over the past several decades there have been extensive scientific and engineering studies on cell materials and degradation behaviors that have greatly improved current density, decreased total resistance, and lowered degradation rates. Although the technology is now at a near-commercial level, maintaining consistency in cell testing and minimizing variance in practical testing environments is an often overlooked but crucial topic. To promote high quality data collection, testing procedures and balance of plant component details are extremely important to consider. This work discusses some key factors affecting the reproducibility of practical SOEC testing on the button cell level, namely, current collection layers, cell sealing procedures, the reliability of steam and hydrogen delivery systems, cell testing fixture design, and reduction procedures. To provide a baseline and a level of standardization for the SOEC community, this work also discloses details of the standard operating procedure and techniques adopted for o-SOEC testing at Idaho National Laboratory (INL).

08 HYDROGEN↗
DOE OSTI2022

Water Electrolyzers and Fuel Cells Supply Chain: Supply Chain Deep Dive Assessment

The report “America’s Strategy to Secure the Supply Chain for a Robust Clean Energy Transition” lays out the challenges and opportunities faced by the United States in the energy supply chain as well as the federal government plans to address these challenges and opportunities. It is accompanied by several issue-specific deep dive assessments, including this one, in response to Executive Order 14017 “America’s Supply Chains,” which directs the Secretary of Energy to submit a report on supply chains for the energy sector industrial base. The Executive Order is helping the federal government to build more secure and diverse U.S. supply chains, including energy supply chains. This report is one of a series that supports the analysis of the energy industrial base called for in Executive Order 14017 on America’s supply chains (Exec. Order No. 14017, 2021). Specifically, it provides a review of the supply chain for water electrolyzers and fuel cells with a focus on polymer electrolyte membrane electrolyzer cells (PEMEC), polymer electrolyte membrane fuel cells (PEMFC), solid oxide electrolyzer cells (SOEC), and solid oxide fuel cells (SOFC). Water electrolysis and fuel cells are a nascent industry with little prior information related to supply chain needs and constraints. This report provides a preliminary assessment; further industry peer review and revisions are expected.

08 HYDROGEN↗
DOE OSTI2021

Energy Arbitrage: Comparison of Options for use with LWR Nuclear Power Plants

Arbitrage is the opportunistic buying and selling of a commodity during local pricing valleys and peaks respectively to maximize economic value. This report evaluates options for energy arbitrage integrated with existing light water reactor (LWR) nuclear power plants (NPPs) where nuclear energy could be stored in a variety of forms and later recovered to generate electrical power during periods when grid electricity demand and pricing are high. The forms of energy storage examined in this report include the potential value of batteries, hydrogen, and thermal energy storage for coupling with nuclear power. Various large demand response options are also analyzed, including the production of liquid nitrogen via air separation and liquefaction, liquefaction of hydrogen, compressed hydrogen, and the cryogenic capture of CO2. Demand response refers to dispatchable loads that can cycle up or down depending on-grid electricity demand to aid in balancing the grid. Large demand response options could dispatch to aid nuclear power stations in avoiding power turndowns by providing an alternate disposition for electrical energy by producing marketable products (e.g., liquid nitrogen, hydrogen, or captured CO2). Static conditions were chosen and analyzed in this report for each option. Dynamic operation or optimization of energy arbitrage or demand response are out of scope for this report. The analysis is based on storage systems with discharge capacities of 500 MW for which various durations of storage and costs of charging (electricity cost) are examined. While the value of thermal energy to an industrial user for flexible plant operations has been previously proven as a business case, this report evaluates costs of hydrogen energy storage and leading thermal energy storage options, and large demand response loads that could be integrated with LWRs in comparison to utility-scale battery storage for use of off-peak nuclear energy. Compilation of this information will be used by the Idaho National Laboratory (INL) RAVEN/HERON systems integration and economics tool to evaluate thermal energy dispatch to industrial users. Relative ranking of energy storage options was done using a levelized cost of storage (LCOS) metric which calculates a rough breakeven cost for the system, taking into account the capital and operating costs as well as the revenue from arbitrage. Table ES1 below shows the LCOS for each of the energy storage options considered. First, in the table, lithium iron (Fe) phosphate batteries are listed as the base case for comparison against the other options. Next is hydrogen storage where most of the hydrogen analyses assumed the hydrogen to be produced using solid oxide electrolytic cell (SOEC) high temperature steam electrolysis (HTSE). The others used existing models of polymer electrolyte membrane (PEM) low temperature electrolysis to produce hydrogen. HTSE performance parameters and costs were taken from existing INL models. Various means were assumed to convert the hydrogen to electricity, including PEM fuel cells (FCs) and a gas turbine mixed in a 30 vol% mixture with natural gas. Physical storage (pressure vessels) and geological storage (natural underground features) were used to store the hydrogen as noted. Geological storage is more economical, but the locations are limited because of the requirement for pre-existing geological formations that will support storage. Thermal energy storage (TES) options were also analyzed including electro-thermal energy storage (ETES) and four different liquid sensible heat TES storage media as noted (Hitec, Hitec XL, Therminol-66, and Dowtherm A). The ETES process considered was modified using existing public documentation on an Echogen process and uses a separate supercritical CO2 charge and discharge cycle with sand as the heat storage media.

25 ENERGY STORAGE↗
DOE OSTI2020

Techno-Economic Analysis of Synthetic Fuels Pathways Integrated with Light Water Reactors

The purpose of this work is to identify, model, perform techno-economic analysis, and compare two possible synfuel production routes utilizing CO 2 as the feedstock. Heat from an LWR nuclear plant is integrated wherever possible to positively affect the economics of the LWR by converting power to fuels during times of low grid electricity demand. Process and economic modeling for a conceptual synfuel production plant co-located (or in near proximity) with an LWR is presented, including the cost of CO 2 captured from an ethanol plant, compressed, and transported to the LWR hybrid plant, co-electrolysis of the CO 2 with water in a solid oxide electrolyzing cell (SOEC) system to produce syngas, and thermocatalytic conversion of the syngas to transportation fuel. The hybrid LWR/synfuels plant is assumed to be located within 50–150 miles of an ethanol plant (e.g., located in the midwest region of the United States). Performance and nth-plant economics for the co-electrolysis-based processes are evaluated and compared with biomass-gasification-based technology for the synfuel routes considered. Sensitivity analysis around the price of CO 2 and electricity, two of the major cost drivers, is presented for each case. Consideration of a carbon credit is also included in the sensitivity analysis.

10 SYNTHETIC FUELS↗
DOE OSTI2023

Proton-Conducting Solid Oxide Electrolysis Cells for Large-scale Hydrogen Production at Intermediate Temperatures

Proton-conducting electrolyte based SOECs offer potential for operation at low to intermediate temperatures. Although yttrium-doped barium zirconate (BZY) and ceria-doped barium zirconate (BCY) have conductivity of 0.01 and 0.017 S.cm -1 respectively at 650C in comparison to the conductivity of 0.015 S.cm -1 for 8-YSZ at 850°C, there remains technology gaps and research needs related to understanding of chemical and structural stability in oxidizing and/or reducing atmospheres at intermediate temperatures, material processing and densification techniques, high polarization losses, and electrode poisoning due to intrinsic and extrinsic gas phase contaminants. Synthesis methods have produced proton-conducting materials and cells that met degradation rate targets, showcasing stable hydrogen production. Improved performance was evident in the HSOEC cell, achieving higher hydrogen production at a lower operating temperature compared to standard cells. Collaborations with multiple research facilities ensured scaling up of synthesis processes and milestone achievements for large-scale manufacturing. Assessment of contaminants revealed their adverse effects on electrode performance and structural stability. Contaminants like Cr and Si compounds, in high humidity, degraded electrodes by forming stable silicate and chromates, inhibiting active surface reactions. Getter materials showed promise in capturing contaminants, suggesting potential for mitigation.

08 HYDROGEN↗
DOE OSTI2023

Techno-Economic Analysis of Reversible and Paired Solid Oxide Cell Systems for Hydrogen Production

This is the Journal of the Electrochemical Society manuscript that details an NETL analysis on comparing the performance and cost of reversible solid oxide cell (SOC) units versus paired fuel cell (SOFC) and electrolysis cell (SOEC) units. The analysis compares tradeoffs such as capital costs versus rate of performance degradation, sensitivity to natural gas prices, sensitivity to imported power costs, and other relevant analyses. The systems include a high rate (98%) of carbon capture. The analysis shows that given a certain cost of electricity input, either approach could be viable in the market and points to the need to incorporate into a full system to understand impacts.

Noring, Alex↗
DOE OSTI2020

Techno-Economic Analysis of Synthetic Fuels Pathways Integrated with Light Water Reactors

The purpose of this work is to identify, model, and compare two possible synfuel production routes utilizing CO 2 as the feedstock. Heat from an LWR nuclear plant is integrated wherever possible as a means to positively affect the economics of the LWR. Process and economic modeling for a conceptual synfuel production plant co-located (or in near proximity) with an LWR is presented, including the cost of CO 2 captured from an ethanol plant, compressed, and transported to the LWR hybrid plant, co-electrolysis of the CO 2 with water in a solid oxide electrolyzing cell (SOEC) system to produce syngas, and thermo-catalytic conversion of the syngas to transportation fuel. The hybrid LWR/synfuels plant is assumed to be located within 50-150 miles of an ethanol plant, e.g., located in the Midwest region of the United States. Performance and nth plant economics for the co-electrolysis-based processes are evaluated and compared with biomass-gasification-based technology for the synfuel routes considered. Sensitivity analysis around the price of CO 2 and electricity, two of the major cost drivers, is presented for each case. Consideration of a carbon credit is also included in the sensitivity analysis.

08 HYDROGEN↗
DOE OSTI2021

A novel solid oxide electrolytic cell with reduced endothermic load for CO 2 electrolysis using (La 0.80 Sr 0.20 ) 0.95 MnO 3-δ cathode

CO 2 conversion to CO via solid oxide electrolysis provides a potentially efficient method for converting CO 2 into an industrially relevant product. A solid oxide electrolysis cell with (La 0.80 Sr 0.20 ) 0.95 MnO 3-δ (LSM) as the CO 2 reduction cathode, yttrium stabilized zirconia (YSZ) as electrolyte, and nickel as the H 2 oxidation anode was operated 800 °C and 850 °C. Thermogravimetric analysis of the LSM material showed no catalyst oxidation at operating temperatures allowing for CO 2 electrolysis without reducing safe gas. In addition, no cathode material mass gain was observed in the presence of CO suggesting little to no carbon deposition occurred above 750 °C. The formation rates of CO for the cell reached 1.15 mL∙min-1∙ cm -2 for an applied current of 150 mA∙cm -2 achieving a faradaic efficiency of 100 %. Furthermore, the cell displayed good stability in the short-term CO 2 electrolysis test with a nominal voltage drop of 4 mV h -1 for 10 h at 850°C. This study shows the feasibility of operating a solid oxide CO 2 electrolysis cell for CO production with H 2 at the anode to reduce endothermic process load.

(La0.80Sr0.20)0.95MnO3-δ↗
DOE OSTI2024

In-House Developed Multiphysics Simulation for the Performance of Solid Oxide Cells (SOCs)

Reversible solid oxide cells(rSOCs) are an enabling energy storage/production technology for a dynamic grid environment. Reversible operation requires strong working knowledge of fuel cell (SOFC) and electrolyzer (SOEC). Performance degradation of SOECs has been observed; however, the details of physical processes related to the performance degradation remain unknown. Multiphysics simulations were performed to investigate the performance degradation of solid oxide electrolysis cells under various working conditions.

Yang, Tao↗