Search NASA⌕ Search

SEARCH · Search NASA

Results for “copper surface”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

EIC Hadron Beamline Vacuum Studies

Ninety percent of the EIC hadron ring vacuum chamber consists of cold-bore sections running through and interconnecting 4.55 K RHIC superconducting (SC) magnets. The EIC operating specification requires shorter bunches and 3x higher intensity beams which are not appropriate for the present RHIC stainless steel cold-bore beam tube. The intensity and emittance of the hadron beams will degrade due to interactions with residual gas or vacuum instabilities arising from the expected resistive-wall (RW) heating, electron clouds, and beam-induced desorption mechanisms. Without strategies to limit RW heating, major cryogenic system modifications are needed to prevent SC magnet quenches. The SC magnet cold-bore beam tubes will be equipped with a high RRR copper-clad stainless steel screen to significantly reduce RW heating and so the effect on the SC magnet cryogenic heat load and temperature. A thin amorphous carbon film applied to the beam-facing copper surface will suppress electron cloud formation. This paper discusses the vacuum requirements imposed by the EIC hadron beams and the plans to achieve the necessary vacuum and thermal stability that ensure acceptable beam quality and lifetime.

43 PARTICLE ACCELERATORS↗
DOE OSTI2021

Initial Assessment of TeF 6 Adsorption

Research and development that supports the management of off-gases from nuclear fuel reprocessing has historically been focused on the off-gas streams that arise from aqueous reprocessing technology. However, as Gen-IV reactor development pathways move toward deployment, alternative spent nuclear fuel (SNF) processing and disposition pathways have been considered more actively. This work is focused upon aspects of fluoride volatility (FV) processing. The versatility of this method for deployment against multiple types of spent fuel encourages the continued advancement of both the primary separations processes and the secondary processes, including waste treatment, material control and accountability, and engineering designs. Recent work noted that TeF 6 , the most highly volatile fluorinated compound produced during FV processing, did not have a clear abatement technology recommended in the literature. Thus, this work performed scoping tests on activated alumina and copper shot to assess whether they could be used to remove TeF 6 from gas streams that bear F 2 . Previous work on this topic was not well described in the literature and was not performed with excess F 2 in the stream as would be typical of spent fuel processing via FV. To support an understanding of the concentration of TeF 6 contacting the adsorbent beds, a series of preliminary testing identified the TeF 6 production rate and the equilibrium concentration of TeF 6 in the gas stream contacting the adsorbent. Excess F 2 was determined to not affect the ability of activated alumina to remove TeF 6 from the gas stream quickly and completely. A determination of whether excess F 2 affected the distribution depth of Te in the sorbent bed is still pending analysis of the used sorbent. Literature suggests that when activated alumina is near saturation, TeF 6 could migrate from the sorbent bed. Future testing should investigate this possibility. Copper metal did not adsorb TeF 6 in the presence of F 2 across the sorbent temperature range of 50 to 335°C. F 2 was fully removed by the copper bed. Although preliminary thermodynamics would indicate adsorption to be energetically favorable, other factors that impact adsorption (e.g., slow kinetics, excess fluorine on the copper surface, an unfavorable transition state) are likely preventing the adsorption of TeF 6 at an easily measurable rate. The work also investigated TeF 6 production from multiple forms of Te in the temperature range of 100 to 250°C. No previous study had assessed the initial reaction rates for this process. A carefully designed study allowed determination of the activation energy for the production of TeF 6 from Te metal. The substantial amount of data collected during this study merits analysis beyond what is described here. A more in-depth kinetic analysis will be pursued. Additional analytical results will provide the ability to benchmark adsorption coefficients for TeF 6 , understand the distribution of TeF 6 within the alumina bed, and better understand the effect of F 2 partial pressure on Te fluorination. The data from this report, as supplemented by these additional analyses, will be submitted to a peer-reviewed journal.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Deactivation of Cu/ZSM-5 Catalysts during the Conversion of 2,3-Butanediol to Butenes

This work determines the deactivation mechanisms of Cu/ZSM-5 catalysts used for the conversion of 2,3-butanediol to butene as part of an alcohol-to-jet route. The deactivation of the catalyst, reflected by a drop in the rate of the limiting hydrogenation step by over 90% in 24 h at a weight hourly space velocity of 5.92 h−1, proceeds via both the agglomeration of copper particles and the obstruction of copper surfaces due to carbonaceous deposits, although the former has less impact on the decrease in the hydrogenation rate. To reduce the detrimental effect of carbonaceous deposits on catalytic activity, ZMS-5 is modified through desilication of the HZSM-5 support with NaOH and CsOH solutions to generate a hierarchical structure with mesopores. The catalyst with the CsOH-treated support generates the highest overall yield of desired olefin products and experiences the slowest deactivation. This is a result of the lower Brønsted acidity and larger mesopores found in the CsOH-treated catalyst, leading to the slower formation of carbonaceous deposits and the faster diffusion of their precursors out of the pores.

Chemistry↗
NASA NTRS1982

Assembling Multicolor Printing Plates

Improved joining method uses wave-soldering techniques developed for integrated-circuit-board assemblies. Thermosetting plastic is replaced by wave soldering, which applies a thin even coat of solder to mating copper surfaces. This is done after ink holes and channels have been protected by water-soluble, high-temperature solder mask which prevents wetting and clogging.

Waters, W. J.↗
NASA NTRS1981

Simultaneous ion sputter polishing and deposition

Results of experiments to study ion beam sputter polishing in conjunction with simultaneous deposition as a mean of polishing copper surfaces are presented. Two types of simultaneous ion sputter polishing and deposition were used in these experiments. The first type utilized sputter polishing simultaneous with vapor deposition, and the second type utilized sputter polishing simultaneous with sputter deposition. The etch and deposition rates of both techniques were studied, as well as the surface morphology and surface roughness.

Rutledge, S.↗
NASA NTRS1986

Development of low-temperature transistor modules to improve the MSFC mid-infrared array

This report describes the low-temperature transistor modules designed for use with the MSFC mid-infrared array. The modules were developed in the Space Science Laboratory at Marshall Space Flight Center with Center Director's Discretionary Funds. The transistors (JFETs), which operate at a temperature of 77 K, are epoxied to a copper surface attached to a Teflon substrate. The module substrate insulates the JFETs from the 1.5K detector work surfaces and provides a convenient mounting structure for additional components such as solder pins. These modules have maintained their structural integrity during repeated temperature cycling, and they have to be convenient during maintenance and servicing of the infrared array.

Telesco, C. M.↗
NASA NTRS1988

The keyhole region in VPPA welds

The morphology and properties of the Variable Polarity Plasma Arc (VPPA) weld composite zone are intimately related to the physical processes associated with the keyhole. The effects of microsegregation and transient weld stress on macrosegregation in the weld tool are examined. In addition the electrical character of straight and reverse polarity portions of the arc cycle were characterized. The results of the former study indicate that alloy 2219 is weldable because large liquid volumes are available during latter stages of weld solidification. Strains in the pool region, acting in conjunction with weld microsegregation can produce macrosegregation great enough to produce radiographic contrast effects in welds. Mechanisms of surface copper enrichment were identified. The latter study has demonstrated that increased heat is delivered to workpieces if the reverse polarity proportion of the weld cycle is increased. Current in the straight polarity portion of the welding cycle increased as the reverse cycle proportion increased. Voltage during reverse polarity segments is large.

Walsh, Daniel W.↗
NASA NTRS1989

Systems tunnel linear shaped charge lightning strike

Simulated lightning strike testing of the systems tunnel linear shaped charge (LSC) was performed at the Thiokol Lightning Test Complex in Wendover, Utah, on 23 Jun. 1989. The test article consisted of a 160-in. section of the LSC enclosed within a section of the systems tunnel. The systems tunnel was bonded to a section of a solid rocket motor case. All test article components were full scale. The systems tunnel cover of the test article was subjected to three discharges (each discharge was over a different grounding strap) from the high-current generator. The LSC did not detonate. All three grounding straps debonded and violently struck the LSC through the openings in the systems tunnel floor plates. The LSC copper surface was discolored around the areas of grounding strap impact, and arcing occurred at the LSC clamps and LSC ends. This test verified that the present flight configuration of the redesigned solid rocket motor systems tunnel, when subjected to simulated lightning strikes with peak current levels within 71 percent of the worst-case lightning strike condition of NSTS-07636, is adequate to prevent LSC ignition. It is therefore recommended that the design remain unchanged.

Cook, M.↗
NASA NTRS2002

Effect of Pin Tool Shape on Metal Flow During Friction Stir Welding

It has been shown that metal moves behind the rotating Friction Stir Pin Tool in two separate currents or streams. One current, mostly on the advancing side, enters a zone of material that rotates with the pin tool for one or more revolutions and eventually is abandoned behind the pin tool in crescent-shaped pieces. The other current, largely on the retreating side of the pin tool is moved by a wiping process to the back of the pin tool and fills in between the pieces of the rotational zone that have been shed by the rotational zone. This process was studied by using a faying surface copper trace to clarify the metal flow. Welds were made with pin tools having various thread pitches. Decreasing the thread pitch causes the large scale top-to-bottorn flow to break up into multiple vortices along the pin and an unthreaded pin tool provides insufficient vertical motion for there to be a stable rotational zone and flow of material via the rotational zone is not possible leading to porosity on the advancing side of the weld.

McClure, J. C.↗
NASA NTRS2016

Origins of Line Defects in Self-Reacting Friction Stir Welds and Their Impact on Weld Quality

Friction stir welding (FSWing) is a solid state joining technique which reduces the occurrence of typical defects formed in fusion welds, especially of highly alloyed metals. Although the process is robust for aluminum alloys, occasional reductions in the strength of FSWs have been observed. Shortly after the NASA-MSFC implemented a variation of FSW called self-reacting (SR), low strength properties were observed. At that time, this reduction in strength was attributed to a line defect. At that time, the limited data suggested that the line defect was related to the accumulation of native oxides that form on the weld lands and faying surfaces. Through a series of improved cleaning methods, tool redesign, and process parameter modifications, the reduction in the strength of the SR-FSWs was eliminated. As more data has been collected, the occasional reduction in the strength of SR-FSW still occurs. These occasional reductions indicate a need to reexamine the underlying causes. This study builds off a series of self reacting (SR)-FSWs that were made in 3 different thickness panels of AA2219 (0.95, 1.27 and 1.56 cm) at 2 different weld pitches. A bead on plate SR-FSW was also made in the 1.56 cm thick panel to understand the contribution of the former faying surfaces. Copper tracer studies were used to understand the flow lines associated with the weld tool used. The quality of the SR-FSWs was evaluated from tensile testing at room temperature. Reductions in the tensile strength were observed in some weldments, primarily at higher weld pitch or tool rotations. This study explores possible correlations between line defects and the reduction of strength in SR-FSWs. Results from this study will assist in a better understand of the mechanisms responsible for reduced tensile strength and provide methodology for minimizing their occurrence.

Schneider, Judy↗
DOE OSTI2021

Copper Dendrites and Surface Engineering for Enhanced CO2 Reduction Research Report Paper

The electrocatalytic reduction of CO 2 (CO 2 R) into hydrocarbon fuels, such as ethylene and ethanol, provides an attractive pathway towards closing the industrial carbon cycle and producing chemicals using renewable electricity. Existing CO 2 R technologies can exhibit C 2+ product selectivity above 74% and operating current densities over 1.3 A/cm 2 , but none can achieve both simultaneously, limiting the commercial viability and scalability of this technology. Low CO 2 concentrations at the catalyst surface and competing side reactions such as the hydrogen evolution reaction (HER) inhibit C 2+ faradaic efficiencies and operational current densities. Additionally, the use of high surface area cathode geometries to increase operational current densities is under-investigated. In this work, we electrodeposit a macroporous copper dendrite film to form high surface area cathodes. These structures are then coated with a combination of hydrophobic/hydrophilic ionomers to achieve high electrochemically active surface areas (ECSA), form regions of intrinsic porosity, and maximize catalytic availability of CO 2 . Using these techniques, we hope to maximize C 2+ faradaic efficiencies (FE) and geometric partial current densities. The treated cathode compound macrostructure (~10μm-sized pores, and ~μm-long dendrites) and concomitant surface area allows increased geometric current densities while the ionomer coating simultaneously inhibits HER and increases hydrogen availability to improve C 2+ selectivity. Our results show that careful engineering of the catalyst-electrolyte interface can enhance CO 2 reduction product selectivity and efficiency.

10 SYNTHETIC FUELS↗
NASA NTRS2007

Formation and Growth of Micro and Macro Bubbles on Copper-Graphite Composite Surfaces

Micro scale boiling behavior in the vicinity of graphite micro-fiber tips on the coppergraphite composite boiling surfaces is investigated. It is discovered that a large number of micro bubbles are formed first at the micro scratches and cavities on the copper matrix in pool boiling. In virtue of the non-wetting property of graphite, once the growing micro bubbles touch the graphite tips, the micro bubbles are sucked by the tips and merged into larger micro bubbles sitting on the tips. The micro bubbles grow rapidly and coalesce to form macro bubbles, each of which sitting on several tips. The growth processes of the micro and macro bubbles are analyzed and formulated followed by an analysis of bubble departure on the composite surfaces. Based on these analyses, the enhancement mechanism of the pool boiling heat transfer on the composite surfaces is clearly revealed. Experimental results of pool boiling heat transfer both for water and Freon-113 on the composite surfaces convincingly demonstrate the enhancement effects of the unique structure of Cu-Gr composite surfaces on boiling heat transfer.

Chao, David F.↗
DOE OSTI2023

Surface Engineering of Copper Catalyst through CO* Adsorbate

The electrochemical reduction of CO 2 with Cu-based catalysts depends intimately on the instantaneous local chemical environment of the catalyst-electrolyte interface. This microenvironment fluctuates according to the concentration of surface-adsorbed competing reaction intermediates and the applied electrode potential. In practice, disentangling these factors is exceedingly challenging, yet they critically determine the electrocatalyst efficiency and selectivity. Using grand canonical quantum-classical hybrid calculations, we quantify the complex interdependence between electrode potential, CO* coverage, and the interfacial field strength. Here we show that the often overlooked CO* coverage effect in fact strongly influences the field strength, with a magnitude change exceeding 1V/Å at certain potentials; among other effects, this change should lower the CO* dimerization barrier that dictates selectivity toward multi-carbon products. Beyond showcasing the importance of surface coverage for CO2 reduction, our results highlight the power of surface additives to modulate interfacial fields toward tailored electrochemical pathways.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
NASA NTRS1971

The interaction of O(plus) ions with the interior surface of a copper chamber

Modulated beams of 0(+), Ar(+), and Kr(+) in the 100-300 eV range are directed into a copper box simulating the ante-chamber of an orbiting mass spectrometer. An RF quadrupole mass spectrometer and phase sensitive detection extract the component of the internal mass spectrum correlated with the beam. Intense Ar and Kr signals are observed; however, no O or O2 is detectable, indicating loss of the primary O(+) beam to surface interactions. All four primary ions stimulate sizeable signals at masses 26 and 28. The relevance of these experiments to the interpretation of mass spectra obtained by orbiting satellites is discussed.

Siegel, M. W.↗