Search NASA⌕ Search

SEARCH · Search NASA

Results for “VOL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Enhancing f -Element Separations with ADAAM-EH: The Impact of Phase Modifiers and a DGA Aqueous Complexant

Recent investigations have used a 2-ethylhexyl diamide amine (ADAAM-EH) for Am/Cm separations in combination with N,N,N ',N '-tetraethyldiglycolamide as an aqueous complexant to achieve an unprecedented separation factor of 41. The aim of this research effort is to understand the speciation of trivalent lanthanide (Ln) and actinide (An) ions in the organic phase of an ADAAM-EH extraction system, both with and without phase modifiers (PM) (1-octanol and tri-n-butyl phosphate (TBP)). Leveraging spectroscopic techniques in combination with distribution ratio measurements provides an understanding of organic phase f-element ligand complexation. In the absence of PM, Ln is extracted in a stoichiometric 1:1 [M(ADAAM-EH) 1 (NO 3 ) x (H 2 O) 1 ](NO 3 ) 3-x complex. The addition of 1-octanol at 20 vol % results in multiple species present. One of the species is the same as the no PM case, and the other species results in an increased -OH coordination to the inner sphere, potentially displacing some NO 3 . In the case of TBP, increasing concentration results in additional red-shifted bands in the UV-visible spectra, suggesting the complexation of additional ligands of either ADAAM-EH or TBP. Finally, the new system knowledge obtained by and spectroscopic experiments will provide benchmarking information for computational studies of the inner- and outer-sphere coordination environments of f-element cations and insights into ADAAM-EH adduct formation with PM, like 1-octanol and TBP.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

A Rapid Microfluidic Neptunium Extraction Using a Supported Liquid Membrane Module

Extraction of neptunium from acidic matrices is important for its quantification, but its complex redox chemistry can cause variable yields. This study develops a microfluidic redox extraction for rapidly separating neptunium from submilliliter samples, achieving up to 90% process yield in less than 10 min for samples as small as 100 μL, with over 97% steady-state yield achieved after 20 min. It uses a supported liquid membrane module loaded with 30 vol % tributyl phosphate in n-dodecane, which performs forward- and back-extractions in a single, continuous step. Neptunium is first oxidized to +6 for extraction and then reduced during stripping. Bromate was selected as an oxidant over permanganate for its greater compatibility with the organic phase, achieving complete oxidation in under 30 s. Ascorbic acid and hydrogen peroxide were both effective reductants. Finally, the system’s high yield and rapid kinetics make it promising for future separations from complex mixtures.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2025

Silver(I) Supported Liquid Membranes for Selective Ethylene Recovery from Mixed-Gas Streams of Tandem CO 2 Electrolysis

Large-scale olefin separations from unreacted paraffins and other byproduct gases are primarily done by energy-intensive cryogenic distillation processes at refineries. Silver(I) supported liquid membranes (Ag SLMs) can be implemented at smaller production scales of ethylene (C 2 H 4 ), a critical industrial chemical, such as its electrocatalytic (EC) production from CO 2 . Challenges of EC C 2 H 4 production mainly stem from reducing gases like hydrogen (H 2 ), where the redox reactions pertinent to Ag(I) facilitators diminish olefin transport. Herein we report that aqueous Ag(I) solution in a composite Ag SLM can operate in mixed-gas conditions containing H 2 gas utilizing reduced titania compounds, such as titanium(III) oxide (Ti 2 O 3 ). Embedding Ti 2 O 3 in the polydimethylsiloxane layer of Ag SLM assisted in selectively separating C 2 H 4 from mixed-gas feed streams related to CO 2 electrolysis containing H 2 . The direct exposure of a mixed-gas stream containing C 2 H 4 , CO 2 , CO, N 2 , and CH 4 with as high as 50 vol % H 2 maintained excellent C 2 H 4 separations for 7 days of continuous operation. The Ag SLM provided effective separations of C 2 H 4 from CO (at detection limits), CH 4 (selectivity ratio (α) = 20–30), and H 2 (α = ∼20), but C 2 H 4 from CO 2 (α = 2–4) revealed a slightly lower separation. These data show that aqueous Ag(I) solution(s) used in the SLMs can separate C 2 H 4 for extended periods, even under highly reducing gas conditions. Also, we report C 2 H 4 recovery from the gas mixture produced in the EC CO 2 reduction process. In conclusion, the Ag SLM gave C 2 H 4 selective separation from a five-component complex mixed-gas stream, relevant to tandem CO 2 electrolysis.

37 - INORGANIC, ORGANIC, PHYSICAL AND ANALYTICAL C↗
DOE OSTI2024

CO 2 Conversion to Butene via a Tandem Photovoltaic–Electrochemical/Photothermocatalytic Process: A Co-design Approach to Coupled Microenvironments

Here, we developed a tandem, unassisted, solar-driven electrochemical and photothermocatalytic process for the single-pass conversion of CO 2 to butene using only simulated solar irradiation as the energetic input. The two-step process involves electrochemical CO 2 reduction (CO 2 R) to ethylene followed by ethylene dimerization to butene. We assessed two unassisted electrochemical setups to concentrate ethylene in the CO 2 R reactor, achieving concentrations up to 5.4 vol.% with 1.8% average solar-to-ethylene conversion and 5.6% average CO 2 -to-ethylene single-pass conversion under 1-sun illumination. When passed through the photothermocatalytic ethylene oligomerization reactor, we generated 600 ppm of butene under 3-sun illumination. Through analysis of this process, we identified that the presence of H 2 , CO, and H 2 O leads to rapid deactivation of the Ni-based ethylene oligomerization catalyst.

14 SOLAR ENERGY↗
DOE OSTI2026

Structure and Flow-Viscosity of Filled-Polymer-Based 3D Printing Ink: Exploration through Coarse-Grained Molecular Dynamics

The addition of nanofiller particles to a polymer matrix has long been known to enhance or modify the composite’s mechanical and rheological properties. However, quantitatively capturing such changes with molecular level simulations remains computationally challenging. Toward that goal, we performed coarse-grained molecular dynamics of a nanocomposite system at a fixed (25 vol %) filler loading under nonspecific, weak polymer–filler interactions representative of a broad class of technologically important materials. We report several interesting results, including: (1) the equilibrium chain-configuration remains Gaussian-like as in an unfilled melt; (2) smaller filler particles display a stronger tendency to cluster; (3) larger fillers act as plasticizers by reducing the entanglement density and accelerating the chain mobility; and (4) fillers enhance the tensile response modulus, with the effect being stronger for larger particles. We also simulate cluster breakup, yielding, and elongational flow under an applied time-linear tensile strain and study the flow viscosity as a function of filler-size and chain-length.

Materials science↗
DOE OSTI2026

Achieving strength-ductility synergy in hierarchical aluminum metal matrix composites via friction extrusion

We report the fabrication of aluminum metal matrix composites (Al-MMCs) with hierarchical architectures via friction extrusion (FE), a scalable, single-step, solid-phase processing technique. Precursor pucks containing 0–15 vol% Al₂O₃ particles were extruded into fully dense AA6061-based composite rods. The FE induced a tree-ring-like architecture of concentric particle-rich and particle-lean bands, yielding refined grains in particle-rich regions and coarser grains elsewhere. At the nanoscale, magnesium in AA6061 selectively reacted with Al₂O₃ particles to form virus-like nodes, improving particle–matrix bonding. This multi-scale design strategy, combining mesoscale architecture, microscale grain refinement, and nanoscale interface engineering overcome the conventional strength–ductility trade-off. Tensile testing showed substantial increases in yield and ultimate tensile strengths while retaining high ductility ( > 20%). Enhanced strain hardening, driven by the accumulation of geometrically necessary dislocations at interfaces, contributed to the performance. The hierarchical microstructure produced by FE demonstrates a promising pathway for scalable fabrication of lightweight MMCs for structural applications requiring a combined high strength and ductility.

Kalsar, Rajib [Pacific Northwest National Laborato↗
DOE OSTI2025

Particle dynamics of nanoplastics suspended in water with soil microparticles: insights from small angle neutron scattering (SANS) and ultra-SANS

Small-angle neutron scattering (SANS) and ultra-SANS (USANS) were employed to understand the aggregation behavior and observe the size reduction for nanoplastics (NPs) formed from a biodegradable mulch film, and microparticles of vermiculite (V), an artificial soil, suspended in water in the presence of low convective shear (ex situ stirring) prior to measurements. Neutron contrast matching was employed to minimize the signal of V (by 100-fold) and thereby isolate the signal due to NPs in the neutron beam, as the contrast match point (CMP) for V (67 vol% deuteration of water) differed from that of NPs by more than 20%. The original NPs' size distribution was bimodal: <200 nm and 500–1200 nm, referred to as small and large NPs, i.e., SNPs and LNPs, respectively. In the absence of V, SNPs formed homoaggregates at higher concentrations that decreased with stirring time, while the size of LNPs remained unchanged. The presence of V at 2-fold lower concentration than NPs did not change the size of SNPs but reduced the size of LNPs by nearly 2-fold as stirring time increased. Because the size of SNPs and LNPs did not differ substantially between CMP and 100% D 2 O solvents, it is evident that SNPs and LNPs are mainly composed of NPs and not V. In conclusion, the results suggest that LNPs are susceptible to size reduction through collisions with soil microparticles via convection, yielding SNPs near soil–water interfaces within vadose zones.

Nanoplastics↗
DOE OSTI2026

Techno-Economic Analysis of Repurposing Natural Gas Transmission Pipeline Networks to Accommodate Hydrogen Blends

Blending hydrogen into natural gas infrastructure could supplement natural gas supply and increase resilience for applications such as ammonia production, peaking and load-following power plants, and heating. The United States has an extensive network of natural gas pipelines, but the feasibility of employing this infrastructure to transport hydrogen is unclear. We analyze the costs associated with repurposing three distinct natural gas transmission pipelines in different locations within the United States to carry blends of hydrogen up to 100% via three different pipeline network modification methods and compare against the cost of building a new dedicated hydrogen pipeline. We conduct a sensitivity analysis on the hoop stress limit of the existing pipe, techno-economic parameters, emissions, and relative capacity. The results show that the capital costs required to upgrade a pipeline can vary from tens of millions to billions of dollars depending on the length and capacity of the existing pipeline section, whether the existing pipeline already operates at or below its maximum allowable operating pressure, whether future demand is expected to increase or decrease, the network modification method selected, and pipe material costs. The delivered cost of energy to end users is impacted less by the levelized cost of transporting hydrogen blends than by the cost of the natural gas and hydrogen fuels being transported. The emissions impact of blending hydrogen into natural gas transmission networks scales proportionally with the amount of energy displaced with low-emission hydrogen (such as from natural gas with carbon capture and sequestration or electrolysis powered by nuclear, renewable, or geothermal electricity), therefore low blend ratios (e.g., < 20% vol. hydrogen) will result in low emissions impacts. Factors such as permitting and right-of-way costs, the proximity of the pipeline to hydrogen demand and production, and the compatibility of and/or retrofitting costs of end-use gas-fueled technologies will likely be greater drivers in determining whether converting a particular natural gas pipeline to carry hydrogen makes economic sense.

08 HYDROGEN↗
DOE OSTI2026

Ammonolysis with N 2 -diluted NH 3 suppresses Ta( IV ) defects in BaTaO 2 N and enhances photocatalytic water oxidation

BaTaO 2 N stands out among oxynitride photocatalysts because of its ability to capture visible light and to drive the photoelectrochemical water oxidation reaction. However, its solar energy conversion performance is limited by electron–hole recombination at Ta( IV ) defects in the material. These defects are formed by overreduction of the Ta(v) oxide precursor by excess ammonia under the high temperature conditions during ammonolysis. Here we show for the first time that Ta( IV ) defect concentrations can be lowered by conducting the ammonolysis reaction in mixed NH 3 /N 2 gas. The obtained BaTaO 2 N samples crystallize in the cubic CaTiO 3 structure type and form 200–300 nm faceted nanocrystals, based on X-ray diffraction, scanning electron microscopy, and HRTEM. Electron paramagnetic resonance spectra observe the Ta( IV ) defects at g = 1.999 and confirm an 11-fold reduction for the product synthesized in mixed (0.13 : 1.0 vol) NH 3 /N 2 gas, equivalent to 1.14 × 10 16 cm −3 Ta( IV ) ions. This optimized BaTaO 2 N has nearly twice the photocatalytic oxygen evolution activity (AQE of 6.78% at 400 nm) of a reference material made with 1.0 atm ammonia and 78% higher photoelectrochemical water oxidation photocurrent (0.9 mA cm −2 at 1.23 V vs. RHE) under simulated sunlight. According to X-ray photoelectron spectroscopy, remaining Ta( IV ) defects are concentrated in the surface region of the BaTaO 2 N particles, where >50% of all Ta ions are found in the +4 oxidation state. This surface Ta( IV ) population can be directly observed in Vibrating Kelvin Probe Surface Photovoltage Spectra (VK-SPV) via its 1.2–1.4 eV photovoltage onset. Here, it suggests that the surface Ta( IV ) ions contribute empty d-states 0.5–0.7 eV below the BaTaO 2 N conduction band edge. These findings highlight how the energetics and concentrations of Ta( IV ) defects influence the photoelectrochemical water oxidation ability of BaTaO 2 N. Additionally, the work establishes ammonolysis with diluted NH 3 as a new tool to minimize defects in BaTaO 2 N and to raise its solar energy conversion efficiency toward its theoretical limit. Because of its simplicity, the reduced ammonia pressure strategy will likely be applicable to other oxynitrides, which generally suffer from overreduction problems during ammonolysis.

Salmanion, Mahya [University of California, Davis,↗
DOE OSTI2026

Solubilization of PET in binary mixtures of HFIP and DCM

The dissolution of polyethylene terephthalate (PET) is a critical step for a solvent-based process, yet it typically requires highly corrosive or toxic solvents. Here, we investigate the solubilization and conformational behavior of PET in binary mixtures of hexafluoro-2-propanol (HFIP) and dichloromethane (DCM) as a strategy to reduce HFIP usage while maintaining effective dissolution. Small-angle neutron scattering (SANS) measurements reveal that PET remains molecularly dissolved in HFIP/DCM mixtures up to 50 vol% DCM. Analysis of PET chain conformations shows a transition from Gaussian behavior at low HFIP fractions to more swollen chains at intermediate compositions, accompanied by a counter-intuitive minimum in the radius of gyration at 50% HFIP. Complementary SANS measurements of the binary solvents demonstrate that compositional heterogeneity is maximized at this same solvent composition, suggesting a direct coupling between solvent microstructure and polymer dimensions. Molecular dynamics simulations corroborate the experimental findings, revealing solvent domain formation, preferential solvation of PET by HFIP, and a “caging” effect arising from solvent heterogeneity that leads to polymer coil compaction. Together, these results provide molecular-level insight into polymer behavior in mixed solvent systems and establish HFIP/DCM mixtures as a promising, more sustainable solvent platform for the PET post-process.

Arifuzzaman, Arif [ORNL]↗
DOE OSTI2025

Actinide oxide dissolution in tributyl phosphate

An alternative to dissolving used nuclear fuel (UNF) in an acidic solution during reprocessing is direct dissolution in an organic solution, which would eliminate an aqueous dissolution step, decrease the amount of nitrate needed, and reduce the facility size. The flowsheet for this potentially less expensive alternative is first to voloxidize the UNF to remove fission product gases and form an oxide. After voloxidation, the UNF is then dissolved in an organic solution containing an extractant mixed with an aliphatic diluent and pre-equilibrated with nitric acid. The organic solution then goes through a solvent extraction process to recover the uranium and/or other desired radionuclides. This work qualitatively studied the dissolution of actinide oxides (UO2, NpO2, and PuO2) in tributyl phosphate using UV-Vis-NIR absorbance spectroscopy to ascertain dissolution behavior. Initial studies included material that is otherwise difficult to dissolve in only nitric acid, specifically CeO2, that is sometimes used as a dissolution surrogate for PuO2. This work confirmed that CeO2, NpO2, and PuO2 are difficult to dissolve in 30 vol% TBP-dodecane pre-equilibrated with 10 M HNO3 and will readily dissolve when co-precipitated with U (i.e., the mixed oxides U-Ce, U-Np, and U-Pu), surrogates for voloxidized nuclear fuel.

Gogolski, Jarrod [Savannah River National Laborato↗
DOE OSTI2025

Interface instabilities in hafnium hydride entrained iron metal matrix composites

The chemical interactions in Fe–HfH 2 metal matrix composites (MMCs) are studied across multiple length scales to elucidate the decomposition of the parent phases and corresponding reaction zone physics during direct current sintering. Fe–HfH 2 composites were synthesized with increasing as-mixed hydride contents of Fe–25% HfH 2 , Fe–40% HfH 2 , Fe–55% HfH 2 , and Fe–70% HfH 2 (all in vol. %) to demonstrate the ability to achieve sintered MMCs with target hydride contents. Samples were probed across multiple length scales through a multi-modal workflow employing x-ray diffraction, scanning electron microscopy and segmentation analysis, and synchrotron techniques including hard x-ray fluorescence mapping and nanoprobe x-ray absorption near-edge structure measurements. Under the selected sintering temperature and pressure conditions, hydrogen evolution is seen to evolve through parallel paths: thermal decomposition from during the transformation of HfH 2 to HfH x<2 and through subsequent reaction with the Fe matrix leading to intermetallic phase formation. Specifically, HfFe and HfFe 2 intermetallic formation accelerates the release of hydrogen with a subsequent HfO 2 phase forming at grain boundaries. For this MMC, the consumption or loss of hydrogen can be considerable in compacts with initial hydride loading of 25%–40% HfH 2 approaching 83% hydrogen loss for the lower volume fraction composites. Increasing the volume fraction of HfH 2 to 70% enhanced the retained hydrogen content to 53% and attributed to the reduced interfacial area intrinsic to the increased HfH 2 loading in this MMC.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Thermophysical Properties of a Uranium Nitride–Molybdenum-Tungsten Composite Fuel for Nuclear Thermal Propulsion

The thermal conductivity of a ceramic-metal composite consisting of 60 vol % uranium nitride incorporated into a molybdenum-tungsten matrix has been measured up to a temperature of 1200°C. Compositing nuclear fuel with refractory materials is considered a viable way to improve the thermal and mechanical properties of fuels, and more recently, has been investigated as a way to improve hydrogen compatibility in a nuclear thermal propulsion rocket reactor. Here, we demonstrate that high-density composites can be produced from direct current sintering and that the resulting thermal conductivity is improved compared to the pure.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2025

Direct Extraction of Uranium-Lanthanide Oxides in Tributyl Phosphate

Abstract Direct extraction of used nuclear fuel (UNF) in an organic solution could be more efficient than the previous practice with aqueous solutions. However, the UNF would need to be treated via voloxidiation before being processed using solvent extraction. The voloxidation process can form oxide and/or nitrate compounds. This work investigated the dissolution of uranium/lanthanide oxides in 30 vol % TBP diluted in dodecane (pre-equilibrated with 4 M nitric acid) in a glass reactor with air sparging to ascertain the uranium/lanthanide oxide dissolution behavior prior to scaling the process. The uranium/lanthanide oxides were prepared by co-precipitating uranium/lanthanide nitrates with hydroxide and then calcined to form a mixed oxide. While the relative concentrations of the lanthanides are not representative of used nuclear fuel, the neodymium and erbium allowed ease of tracking dissolution with visible spectroscopy. Cerium was used as a surrogate for plutonium. The dissolution rate of the oxides was similar but incomplete. A miniscule amount of cerium, as cerium oxide, took several months to slowly dissolve; however, when co-precipitated with uranium and other lanthanides, a significant amount of cerium dissolved readily.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2025

Thermophysical Properties of Ti3SiC2 MAX Phase Composites with SiC Reinforcement

In the present work, dense (∼100%) Ti 3 SiC 2 composites (TSC) are processed along with 20 vol% of SiC reinforcement (TSC20) via spark plasma sintering at 1400°C, 40 MPa, 15 min, and dynamic vacuum environment. Thermal expansion of both the composites increases from RT to 1273 K and linear fitting of data yields coefficient of thermal expansion (CTE) of 9.4 × 10 −6 K −1 for TSC which decreases to 8.3 × 10 −6 K −1 for TSC20. With increase in temperature from RT to 773 K, specific heat for both TSC and TSC20 composites is observed to increase from 598-850 J.kg −1 .K −1 , whereas thermal diffusivity and thermal conductivity values decrease with testing temperature. SiC reinforcement in Ti 3 SiC 2 resulted in improved thermal diffusivity from 12.7 to 18.7 mm 2 .s −1 and thermal conductivity from ∼57 to ∼79 W.m −1 .K −1 at RT. However, with increase in temperature (773 K), thermal diffusivity and conductivity decrease, and values get closer for both TSC and TSC20 composites. Further extrapolation of thermal conductivity data showed cross-over at ∼973 K due to domination of phonon-phonon scattering and thus lower values of thermal conductivity for TSC20 than TSC. Therefore, reduced CTE and higher thermal conductivity of TSC20 make it a viable choice for applications in high temperatures.

36 MATERIALS SCIENCE↗
DOE OSTI2026

ReMU: regional minimal updating for model-based derivative-free optimization

Derivative-free optimization (DFO) problems are optimization problems where derivative information is unavailable or extremely difficult to obtain. Model-based DFO solvers have been applied extensively in scientific computing. Powell's NEWUOA (2004) [Powell, The NEWUOA software for unconstrained optimization without derivatives, in Large-Scale Nonlinear Optimization, Nonconvex Optimization and its Applications Vol. 83, G. Di Pillo and M. Roma, eds., Springer, 2006, pp. 255–297] and Wild's POUNDerS (2014) [Wild, Solving derivative-free nonlinear least squares problems with POUNDERS, in Advances and Trends in Optimization with Engineering Applications, T. Terlaky, M.F. Anjos, and S. Ahmed, eds., SIAM, 2017, pp. 529–540] explore the numerical power of the minimal norm Hessian (MNH) model for DFO and contributed to the open discussion on building better models with fewer data to achieve faster numerical convergence. Another decade later, we propose the regional minimal updating (ReMU) models, and extend the previous models into a broader class, including the H 2 norm models [Xie and Yuan, Least H 2 norm updating of quadratic interpolation models for derivative-free trust-region algorithms, IMA J. Numer. Anal. 46 (2025), pp. 21–50]. This paper shows motivation behind ReMU models, computational details, theoretical and numerical results on particular extreme points and the barycentre of ReMU's weight coefficient region, and the associated KKT matrix error and distance. Novel metrics, such as the truncated Newton step error, are proposed to numerically understand the new models' properties. A new algorithmic strategy, based on iteratively adjusting the ReMU model type, is also proposed, and shows numerical advantages by combining and switching between the barycentric model and the classic least Frobenius norm model in an online fashion.

derivative-free trust-region methods↗
DOE OSTI2025

Non-solvents as physical blowing agents in printable silicone foams

Silicone foams were produced by dispersing an incompatible liquid phase (i.e. a non-solvent) into an uncured, liquid silicone. The formulation and processing parameters were varied to see the effect on porosity and pore morphology. Specifically, two fluorosilanes were added to stabilize the inclusion of fluorinated solvents as blowing agents. As the floruosilane content increased, the void content increased up to about 44 vol. % when the fluorosilane comprised 18 wt. % of the initial formulation. Fumed silica that was treated with a fluorinated silane was also used to try to stabilize the dispersed liquid. While the fumed silica content did not have a strong effect on the total void content, the morphology changed when silica content changed. Various fluorinated solvents with distinct chemical structures were used as the non-solvent and then removed after curing of the silicone. The interaction of the internal non-solvent phase and the silicone phase was expected to influence the porosity. These insights highlight how the manipulation of formulation and processing parameters, focusing on the inclusion of fluorosilanes and fluorinated solvents, contributes to the understanding of how incompatible liquid phases interact with silicone matrices to control porosity and pore morphology. Additionally, these interactions also influenced processability, leading to formulations that could be printed. Higher content of non-solvent inclusions could increase the yield stress and storage modulus of an uncured formulation, leading to the ability to tune intrastrand porosity while a 3D printed architecture could be modified to introduce porosity between the strands. Furthermore, in addition to fluorinated solvents, we also considered non-fluorinated solvents since these may be more industrially relevant in the future. Overall, this approach provides an alternative route to producing porous foams that can be 3D printed, which could be useful for applications like cushioning and protective gear.

physical blowing agent↗