Search NASA⌕ Search

SEARCH · Search NASA

Results for “Li-ion battery cathode”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Laser ablation of high-loading Li-ion battery electrodes improves accessible capacity and cycle life for Behind-the-Meter Storage

Adoption of Behind-the-Meter Storage (BTMS) requires design of batteries that enable high safety, long cycle life, and low cost at the system level. Pairing Li 4 Ti 5 O 12 (LTO) with LiMn 2 O 4 (LMO) achieves targets related to safety and cycle life, but these materials' low energy densities contribute to higher cost at the system scale. Increasing electrode loading is a simple approach to improve energy density, but comes with a trade-off in electrode utilization due to long, tortuous Li + diffusion pathways. Here, laser ablation is used to microstructure (pattern) high-loading electrodes to enhance electrode performance through improved Li + diffusion pathways. Four cell types, comprising combinations of standard or patterned anode and cathode, were prepared to evaluate the effects of laser ablation at each electrode. A rate test shows that patterning electrodes enhances active material utilization at ≳1C rates. Patterning the cathode yields the most benefit, as cells with a patterned cathode demonstrate a ~20% higher accessible capacity than those without at 1.4C. Additionally, 1C capacity retention of cells with patterned cathode (91% through 3000 cycles) is significantly improved over cells with only the anode patterned (64%) and non-patterned electrodes (50%). Characterization of post-mortem cells before and after refreshing their electrolyte suggests that 1C capacity retention is improved by mitigation of electrode "dry-out". We hypothesize that the microstructure acts as a reservoir of additional electrolyte, or a path for gas to escape, so that active material remains wetted throughout long-term cycling, and/or the microstructure may reduce localized, gas-forming overpotentials in the high-loading electrode.

25 ENERGY STORAGE↗
DOE OSTI2026

Single-crystal NMC622 from combustion-assisted solid-state synthesis: Tunable particle size, voltage-dependent stability, and Li-ion diffusion

Cost-effective and scalable synthesis of single-crystal lithium–metal-oxide cathodes with controlled size and morphology remains challenging for advancing high-performance lithium-ion batteries. Here, we demonstrate a solution combustion–assisted solid-state method for producing single-crystal NMC622 with tunable particle size at various lithium stoichiometries. Structural and electronic characteristics were probed using synchrotron-XANES, EXAFS, XRD and XPS, confirming well-defined coordination environments and phase purity up to Li ≈ 1.3. The electrochemical behavior of LixNMC (x = 1.0 and 1.3) single crystals was evaluated across 2.8–4.3 V and 2.8–4.7 V windows to elucidate the effects of lithium content and operating voltage. At 2.8–4.3V, Li1.3NMC exhibits higher initial capacity due to its larger lithium inventory, while Li1.0NMC shows superior long-term retention driven by its larger crystal size and reduced structural distortion. Increasing the cutoff voltage to 4.7 V enhances the initial capacity of both compositions by 17–25%, but long-term capacity retention ultimately converges to values comparable to those at 4.3 V due to voltage-induced degradation, where Li+ diffusion constant remains lying ranging from 10−12 –10−11 cm2s−1. Overall, this study establishes a scalable combustion-assisted route for synthesizing tunable single-crystal NMC622 and highlights the interplay between lithium stoichiometry, particle size, and voltage window in governing cathode stability.

Roy, Subrata C [Jackson State University]↗
DOE OSTI2025

Single-Crystallization of O3-Type Layered Oxide Cathode for Na-Ion Battery

The development of high-energy-density Na-ion batteries places significant demands on single-crystal layered oxide cathodes, especially for further high-voltage, solid-state battery scenarios. In the O3-type structure, due to the original sluggish Na ion diffusion kinetics (approximately 1 order of magnitude lower than that of Li-ion), and further hindrance against diffusion kinetics caused by single-crystal architecture, these inherent defects lead to the decline in the electrochemical performance. Herein, we demonstrated that the single crystallization of O3-type NaNi 1/3 Fe 1/3 Mn 1/3 O 2 cathode (d 50 = 5.04 μm) aggravates surface-to-bulk phase inhomogeneity distribution, which is attributed to the uneven Na ions extraction. Moreover, the Na-depletion of the surface/shell region not only aggravates Na ion diffusion resistance but also leads to a higher valence state of transition-metal elements (e.g., Ni/Fe) near the surface of the single-crystal particle, which further compromises the cathode-electrolyte interface stability. Furthermore, not limited to revealing the challenges, tuning the particle size and moderating quasi-single-crystal strategies have been proven to effectively mitigate the negative uneven distributions of Na ions, phases, and valence/oxidative states, resulting in efficient modification for single crystallization of Na-layered oxide cathodes.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Sodium-Ion Battery Cathode with Dominating Copper and Oxygen Redox Chemistry

Sodium-ion batteries offer low-cost energy storage solutions for the grid and electric vehicles, leveraging the established "rocking-chair" Li-ion design and the natural abundance of sodium. However, SIBs face challenges such as relatively lower voltage and capacity than lithium-ion batteries, as well as dependence on nickel resources. Here, in this work, a new nickel-free cathode material, Na 0.75 Li 0.08 Cu 0.25 Mn 0.66 O 2 , was designed and synthesized. This material has a capacity of ~125 mAh/g and an average discharge voltage of 3.5 V. Notably, more than one-third of the capacity arises from lithium substitution of Cu (~8 mol.%) and high voltage activation to 4.6 V. Multimodal synchrotron x-ray characterization combining spectroscopy, microscopy, and scattering reveal the capacity is primarily from the redox of copper and oxygen, with a minor contribution from the manganese redox. Lithium substitution alters the phase transition mechanism from a two-phase transition in P3-Na 2/3 Cu 1/3 Mn 2/3 O 2 to a solid-solution in Na 0.75 Li 0.08 Cu 0.25 Mn 0.66 O 2 , enhancing the reversibility of this material.

25 ENERGY STORAGE↗
DOE OSTI2025

Stable-Cycling Sustainable Na-Ion Batteries with Olivine Iron Phosphate Cathode in an Ether Electrolyte

Sustainable batteries using nontoxic, earth-abundant, and low-cost materials are key to decarbonization. Olivine NaFePO 4 fulfills these criteria, is attractive for Na-ion batteries, and can be derived from LiFePO 4 recycled from Li-ion battery wastes. Critical knowledge is needed for transforming LiFePO 4 to NaFePO 4 to enable such a sustainable, green engineering path toward high-performance Na-ion batteries. Herein, we report on the development of a stable-cycling, sustainable olivine iron phosphate-based Na-ion battery empowered by an improved understanding of materials transformation and electrolyte chemistry. First, we found that the conventional carbonate electrolyte with fluoroethylene carbonate additive causes an additional plateau (~2.4 V) at the end of the discharge process of the FePO 4 ||Na metal cell, leading to lower initial discharge capacity and voltage. This result shows that the voltage profile is influenced by not only intrinsic materials phase transformation during battery cycling but also the electrolyte additives and interphases formed. With the 1 M NaPF 6 diglyme electrolyte, we achieved an excellent capacity retention of 96% and 98% after 500 cycles at 1 and 5 C, respectively. Second, we chemically sodiated FePO 4 to form single-phase Na 0.9 FePO 4 . Na 0.9 FePO 4 ||hard carbon full cells demonstrated a remarkable capacity retention of ~84% at 3 and 5 C after 1000 cycles. The successful implementation of hard carbon, which can be derived from biomass waste, will further improve the sustainability of energy storage technologies. Our research demonstrates that electrolyte chemistry influences the voltage profile of phase-changing electrodes and provides effective electrolyte and full-cell design solutions for stable-cycling NaFePO 4 .

36 MATERIALS SCIENCE↗
DOE OSTI2025

Nucleation-promoting and growth-limiting synthesis of disordered rock-salt Li-ion cathode materials

Disordered rock-salt oxides and oxyfluorides are promising positive electrode materials for high-performance lithium-ion batteries free of nickel and cobalt. However, conventional synthesis methods rely on post-synthesis pulverization to achieve cycling-appropriate particle sizes, offering limited control over particle microstructure and crystallinity. This accelerates degradation and complicates secondary particle processing. Here we present a synthesis strategy that enhances nucleation while suppressing particle growth and agglomeration across various disordered rock-salt compositions, including lithium–manganese–titanium oxide, lithium–manganese–niobium oxide, and lithium–nickel–titanium oxide systems. Applied to Li 1.2 Mn 0.4 Ti 0.4 O 2 , this method yields highly crystalline, well-dispersed sub-200 nm particles that form homogeneous electrode films with stable cycling behavior. Tested in cells with lithium metal as the counter electrode, these electrodes deliver ~200 mAh/g with 85% capacity retention relative to the first cycle after 100 cycles (20 mA/g, 1.5–4.8 V), and an average discharge voltage loss of 4.8 mV per cycle, compared to 38.6% retention and 7.5 mV loss per cycle for electrodes derived from pulverized solid-state particles. This approach suggests a route to enhance the performance and durability of disordered rock-salt electrodes for sustainable lithium-ion batteries.

Batteries↗
DOE OSTI2024

Earth-abundant Li-ion cathode materials with nanoengineered microstructures

Manganese-based materials have tremendous potential to become the next-generation lithium-ion cathode as they are Earth abundant, low cost and stable. Here we show how the mobility of manganese cations can be used to obtain a unique nanosized microstructure in large-particle-sized cathode materials with enhanced electrochemical properties. By combining atomic-resolution scanning transmission electron microscopy, four-dimensional scanning electron nanodiffraction and in situ X-ray diffraction, we show that when a partially delithiated, high-manganese-content, disordered rocksalt cathode is slightly heated, it forms a nanomosaic of partially ordered spinel domains of 3–7 nm in size, which impinge on each other at antiphase boundaries. The short coherence length of these domains removes the detrimental two-phase lithiation reaction present near 3 V in a regular spinel and turns it into a solid solution. This nanodomain structure enables good rate performance and delivers 200 mAh g –1 discharge capacity in a (partially) disordered material with an average primary particle size of ~5 µm. The work not only expands the synthesis strategies available for developing high-performance Earth-abundant manganese-based cathodes but also offers structural insights into the ability to nanoengineer spinel-like phases.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Low-cost iron trichloride cathode for all-solid-state lithium-ion batteries

The dominant chemistries of lithium-ion batteries on the market today still rely on flammable organic liquid electrolytes and cathodes containing scarce metals, such as cobalt or nickel, raising safety, cost and environmental concerns. Here we show a FeCl 3 cathode that costs as little as 1% of the cost of a LiCoO 2 cathode or 2% of a LiFePO 4 cathode. Once coupled with a solid halide electrolyte and a lithium-indium (Li–In) alloy anode, it enables all-solid-state lithium-ion batteries without any liquid components. Notably, FeCl 3 exhibits two flat voltage plateaux between 3.5 and 3.8 V versus Li + /Li, and the solid cell retains 83% of its initial capacity after 1,000 cycles with an average Coulombic efficiency of 99.95%. Combined neutron diffraction and X-ray absorption spectroscopy characterizations reveal a Li-ion (de)intercalation mechanism together with a Fe 2+ /Fe 3+ redox process. Further, our work provides a promising avenue for developing sustainable battery technologies with a favourable balance of performance, cost and safety.

25 ENERGY STORAGE↗
DOE OSTI2024

Electrolyte and Cutoff Potential Effects on Cycle Life of Li4Ti5O12/LiNi0.9Mn0.1O2 Batteries for Behind-the-Meter Storage Applications

Behind-the-Meter Storage (BTMS) is a stationary battery energy storage system that is connected to the electrical distribution system on the customer's side of the utility's service meter. BTMS systems are used to store electrical energy from the grid as well as inconstant, renewable energy, such as local solar and wind generation. A successful BTMS system will allow the customer to pair their energy generation and storage to optimize electrical consumption from the grid, improving reliability and minimizing cost. For BTMS applications, batteries must be designed and optimized with different set of criteria from other leading segments of the Li-ion battery market, like transportation, due the system being stationary and proximal to the residential or commercial building it's benefitting. BTMS applications prioritize safety, cost (low/no-critical materials), reliability (20-year calendar life), and durability (10,000 cycle life), while having the ability to (minimally) compromise energy density and rate capability. Lithium titanate (Li4Ti5O12-, LTO) is a promising anode candidate for BTMS applications due to its high safety and capacity retention, while maintaining a reasonable 160 mAhg-1 reversable capacity and composition of relatively abundant materials. (1) Specifically, LTO has a high working voltage which helps to prevent Li dendrite formation, improving safety. Furthermore, LTO also has negligible lithiation-based volume change, leading to less mechanical pulverization, or loss of active material, upon cycling. For the cathode, materials with little or no Co are of high interest due to the high cost and low abundance of Co. LiMn2O4 (LMO) has been paired with LTO for BTMS applications in the past due to its safety, low cost (abundancy), and reasonably high operating voltage. (2-4) However, the low capacity of LMO limits energy density and specific energy. While not the highest priority for BTMS applications, increasing energy density will enable deployment in space constrained BTMS applications and decrease total cost. LiNi0.9Mn0.1O2 (LN-MO) is a recently developed material with promise due to its high operating voltage and relatively low price. (5) However, Ni-rich layered oxides, including LNMO, tend to struggle with capacity retention during high-voltage cycling due to mechanical pulverization, irreversible phase transitions, and unstable solid-electrolyte interphase. The study presented here focuses on building an understanding of how electrolyte solvent and varied cutoff potentials will impact the cycle life of LTO/LN-MO cells. Specifically, a comparison is provided between ethylene carbonate (EC), ethyl methyl carbonate (EMC), fluoroethylene carbonate (FEC), and Gen2 electrolyte solvents with 1M Lithium hexafluorophosphate (LiPF6) salt, cycling to two upper termination potentials, 2.6V and 2.7V. Electrochemical testing and diagnostics (e.g., differential capacity analysis, area specific impedance, constant voltage hold, and rate capability) and post-mortem characterization will be used to understand the aging behavior and failure mechanisms of the 8 cell combinations (four electrolytes and two voltage cutoffs). Cells with FEC electrolyte showed a lower initial capacity compared to cells with Gen2, EMC, and EC cycling at both voltages; however, the cells with FEC showed consistent trends in capacity retention with 2.6V and 2.7V termination potentials, while the cells with the other electrolytes showed much higher rates of capacity loss when cycling to the higher voltage. These results indicate that FEC may play a role in improving durability of high-voltage, Ni-rich electrode systems for use in high-cycle applications, such as BTMS.

electrolyte↗
DOE OSTI2024

Elucidating the Link Between Alkali Metal Ions and Reaction-Transport Mechanisms in Cathode Electrodes for Alkali-ion Batteries

Our long-term goal is to improve the reliability of electrode materials and their ability to transport and store various metal ions for electrochemical energy storage applications. The main objective of this work was to investigate the intrinsic relationship between the role of alkali metal ions and electrochemically driven mechanical stability and kinetic properties of battery materials. The overall question was “What is the role of alkali metal ions on the electrochemical and mechanical behavior of cathode electrodes? Our guiding hypothesis was that intercalation of larger alkali metal ions (Na and K) inevitably alters the coupled transport-reaction processes during battery operation in organic electrolytes, leading to more intensive chemo-mechanical instabilities in cathode electrodes, resulting in rapid capacity fade. To validate the hypothesis, we experimentally characterized the reaction-transport processes and governing forces driving the instability of electrode materials in different alkali metal-ion environments. The project had three main tasks. The first one was to investigate intercalation-induced strains and associated stress generation, and their impact on structural deformations in composite cathode electrodes. The second task focused on identifying potential-dependent dynamic changes in the electrode-electrolyte interface in alkali metal ion batteries. The last task was focused on determining how larger alkali metal ions with slower diffusivity affect the transport-mechanics coupling at faster scan rates, compared to smaller ions with faster diffusivity in electrodes. We shortly provided the outcome of each task in the accomplishment section. This project produced 10 peer-reviewed publications (9 research papers and one review manuscript) and supported two Ph.D. students, who graduated from Oklahoma State University.

25 ENERGY STORAGE↗
DOE OSTI2025

Development of a High-Rate Lithium-Air Battery Using a Gaseous CO 2 Reactant

Li-air batteries are considered a potential alternative to Li-ion batteries for transportation applications due to their high theoretical specific energy. Most works in this area focus on use of O 2 as the reactant. However, newer concepts for using gaseous reactants (such as CO 2 , which has a theoretical specific energy density of 1,876 Wh/kg) provide opportunities for further exploration. The main objective of this project was the development of a novel strategy that enables operation of Li-CO 2 batteries at high-capacity and high-rate, with a long-cycle-life. The team was able to: (1) Synthesize two novel transition metal chalcogenide (TMC) catalysts that work in synergy with ionic liquid-based electrolytes to enhance the efficiency of reactions during discharge and charge processes; (2) Fabricate high-porosity cathode electrodes with 3D printing to increase electrode surface area and gas permeability; (3) Develop a multiscale modeling framework that integrates Density Functional Theory (DFT), Ab-Initio Molecular Dynamics (AIMD), classical Molecular Dynamics (MD), and Finite Element Analysis (FEA) to investigate atomic and cell-level properties of Li-CO 2 batteries; (4) Assemble a stackable Li-CO 2 pouch-cell able to deliver a capacity of >200 mAh. These achievements were realized through an integrated approach based on materials synthesis, testing, characterization, analysis, and computation. This project produced a thorough understanding of key chemical, electronic, and kinetic parameters that govern the operation of Li- CO 2 batteries in realistic conditions. The methodologies employed, and the insight generated, will be valuable beyond advancing the field of Li-CO 2 batteries

25 ENERGY STORAGE↗
NASA NTRS2003

Li-ion cells for terrestrial robots

SAFT prismatic wound 5 Ahr MP series cells were evaluated for potential application in a lithium ion battery designed for Tactical Mobile Robots (TMR). In order to satisfy battery design requirements, a 10 Ahr battery containing two parallel 8-cell strings was proposed. The proposed battery has a weight and volume of approximately 3.2kg and 1.6 liters, respectively. Cell qualification procedures include initial characterization, followed by charge/discharge cycling at 100% DOD with intermittent EIS measurements at various state of charge. Certain cells were also subjected to extreme operational temperatures for worst-case analysis. Excellent specific energy (>130 Whr/kg) was obtained with initial characterization cycles. Even at abusive thermal conditions, the cell capacity fade was less than Ahr after 300 cycles. Rate characterization showed good cell discharge behavior with minimal decrease in capacity. At various state of charge, impedance measurements suggest that the cathode play a more significant role in capacity. At various state of charge impedance measurements suggest that the cathode play a more significant role in capacity fade than the anode.

robots↗
NASA NTRS2005

Nanostructured and layered lithium manganese oxide and method of manufacturing the same

Nanostructured and layered lithium manganese oxide powders and methods of producing same. The powders are represented by the chemical formula, LixMn1-yMyO2, where 0.5<x<1.33, 0?y?0.5 and have an average primary particle diameter from 5 nm to 300 nm, preferably between 5 and 100 nm, and M is at least one cation dopant. The powders can be formed into active cathode materials in Li-ion and Li rechargeable batteries.

Singhal, Amit↗
NASA NTRS2010

Optimized Li-Ion Electrolytes Containing Fluorinated Ester Co-Solvents

A number of experimental lithium-ion cells, consisting of MCMB (meso-carbon microbeads) carbon anodes and LiNi(0.8)Co(0.2)O2 cathodes, have been fabricated with increased safety and expanded capability. These cells serve to verify and demonstrate the reversibility, low-temperature performance, and electrochemical aspects of each electrode as determined from a number of electrochemical characterization techniques. A number of Li-ion electrolytes possessing fluorinated ester co-solvents, namely trifluoroethyl butyrate (TFEB) and trifluoroethyl propionate (TFEP), were demonstrated to deliver good performance over a wide temperature range in experimental lithium-ion cells. The general approach taken in the development of these electrolyte formulations is to optimize the type and composition of the co-solvents in ternary and quaternary solutions, focusing upon adequate stability [i.e., EC (ethylene carbonate) content needed for anode passivation, and EMC (ethyl methyl carbonate) content needed for lowering the viscosity and widening the temperature range, while still providing good stability], enhancing the inherent safety characteristics (incorporation of fluorinated esters), and widening the temperature range of operation (the use of both fluorinated and non-fluorinated esters). Further - more, the use of electrolyte additives, such as VC (vinylene carbonate) [solid electrolyte interface (SEI) promoter] and DMAc (thermal stabilizing additive), provide enhanced high-temperature life characteristics. Multi-component electrolyte formulations enhance performance over a temperature range of -60 to +60 C. With the need for more safety with the use of these batteries, flammability was a consideration. One of the solvents investigated, TFEB, had the best performance with improved low-temperature capability and high-temperature resilience. This work optimized the use of TFEB as a co-solvent by developing the multi-component electrolytes, which also contain non-halogenated esters, film forming additives, thermal stabilizing additives, and flame retardant additives. Further optimization of these electrolyte formulations is anticipated to yield improved performance. It is also anticipated that much improved performance will be demonstrated once these electrolyte solutions are incorporated into hermetically sealed, large capacity prototype cells, especially if effort is devoted to ensure that all electrolyte components are highly pure.

Prakash, G. K. Surya↗
NASA NTRS2012

Electrolytes for Use in High Energy Lithium-ion Batteries with Wide Operating Temperature Range

Met programmatic milestones for program. Demonstrated improved performance with wide operating temperature electrolytes containing ester co-solvents (i.e., methyl butyrate) containing electrolyte additives in A123 prototype cells: Previously demonstrated excellent low temperature performance, including 11C rates at -30 C and the ability to perform well down to -60 C. Excellent cycle life at room temperature has been displayed, with over 5,000 cycles being demonstrated. Good high temperature cycle life performance has also been achieved. Demonstrated improved performance with methyl propionate-containing electrolytes in large capacity prototype cells: Demonstrated the wide operating temperature range capability in large cells (12 Ah), successfully scaling up technology from 0.25 Ah size cells. Demonstrated improved performance at low temperature and good cycle life at 40 C with methyl propionate-based electrolyte containing increasing FEC content and the use of LiBOB as an additive. Utilized three-electrode cells to investigate the electrochemical characteristics of high voltage systems coupled with wide operating temperature range electrolytes: From Tafel polarization measurements on each electrode, it is evident the NMC-based cathode displays poor lithium kinetics (being the limiting electrode). The MB-based formulations containing LiBOB delivered the best rate capability at low temperature, which is attributed to improved cathode kinetics. Whereas, the use of lithium oxalate as an additive lead to the highest reversible capacity and lower irreversible losses.

low temperature batteries↗
NASA NTRSDate not supplied

Elucidation of Electrolyte Decomposition Pathways in Li--O2 Batteries using Ab Initio Computations

Li-O2 batteries offer exciting possibilities for energy-storage applications requiring higher energy content than current Li-ion battery technologies. However, development of commercial Li-O2 batteries faces many challenges including electrolyte decomposition in order to realize the full potential of this emerging technology. In this work, we present ab initio calculations that probe the role of reactive oxygen species including singlet oxygen, superoxide, and peroxides on electrolyte decomposition for potential organic electrolytes for use in Li-O2 batteries. We investigate the influence that the harsh electrochemical environment near the cathode plays in promoting electrolyte decomposition by using increasingly detailed computational models. Our results highlight existing problems with organic electrolytes for Li-O2 battery development and suggest potential design strategies for reducing electrolyte decomposition.

Li-O2 Batteries↗
NASA NTRS2020

Toward Realizing the Potential of Practical Li-O2 Batteries for Electric Aircraft

Electrochemical power sources based on the Li-O2 couple have potential to achieve more than two-times the specific energy that is achievable with state-of-the-art Li-ion technologies. Despite considerable research, significant practical limitations continue to impede the successful realization of the Li-O2 electrochemistry as a power source in electric and hybrid-electric aviation. In practice, power capability and cycle life present formidable challenges. In this work, projections are presented for Li-O2prismatic cells with lightweight construction and the effect of cathode-limited capacity and discharge rate on specific energy and power are presented.

William R Bennett↗
NASA NTRS2017

Factors Limiting Li+ Charge Transfer Kinetics in Li-ion Batteries

Understanding the factors limiting Li+ charge transfer kinetics in Li-ion batteries is essential in improving the rate performance, especially at lower temperatures. The Li+ charge transfer process involved in the lithium intercalation of graphite anode includes the step of de-solvation of the solvated Li+ in the liquid electrolyte and the step of transport of Li+ in the preformed solid electrolyte interphase (SEI) on electrodes until the Li+ accepts an electron at the electrode and becomes a Li in the electrode. Whether the de-solvation process or the Li+ transport through the SEI is a limiting step depends on the nature of the interphases at the electrode and electrolyte interfaces. Several examples involving the electrode materials such as graphite, lithium titanate (LTO), lithium iron phosphate (LFP), lithium nickel cobalt aluminum oxide (NCA) and solid Li+ conductor such as lithium lanthanum titanate or Li-Al-Ti-phosphate are reviewed and discussed to clarify the conditions at which either the de-solvation or the transport of Li+ in SEI is dominating and how the electrolyte components affect the activation energy of Li+ charge transfer kinetics. How the electrolyte additives impact the Li+ charge transfer kinetics at both the anode and the cathode has been examined at the same time in 3-electrode full cells. The resulting impact on Li+ charge transfer resistance, Rct, and activation energy, Ea, at both electrodes are reported and discussed.

Delp, Samuel A.↗