Search NASA⌕ Search

SEARCH · Search NASA

Results for “composite cathode”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Manganese-rich high entropy oxides for lithium-ion batteries:materials design approaches to address voltage fade

Lithium- and manganese-rich oxides are of interest as lithium-ion battery cathode materials as Mn is earth abundant, low cost, and can deliver high capacity. Herein, a high entropy strategy was used to prepare Mn rich high entropy oxide (HEO) materials by including four additional metals (Ni, Co, Fe and Al) in the compositions using a mild co-precipitation method. Two HEOs (Li x Ni 0.1 Mn 0.6 Co 0.1 Al 0.1 Fe 0.1 O y , where x = 1.5 for HEO-L and x = 0.5 for HEO-H) with layered and spinel-layered hybrid structures were investigated where the morphology, elemental composition, structure, atomic level phase distribution, and electrochemistry were determined. The HEO-L samples involve a Li 2 TMO 3 layered structure with ~39% stacking faults. HEO-H is a hybrid structure comprised of 80 wt% spinel and 20 wt% LiMO 2 layered structure. The high entropy manganese-rich HEO-L showed higher capacity and 93% retention of the average voltage after 100 cycles while HEO-H showed higher capacity retention and near 100% average voltage retention. Finally, operando X-ray absorption spectroscopy revealed that the Ni, Co, and Mn are redox active in both materials while the Fe center remains at the Fe 3+ oxidation state throughout cycling, where the changes in the oxidation states for both materials during discharge were consistent with the delivered electrochemical capacity rationalizing the observed electrochemistry.

25 ENERGY STORAGE↗
DOE OSTI2026

Influence of aluminum source and Ni/Al ratio in a batch stirred tank reactor on the structure, morphology, and electrochemical performance of Ni-rich NMA cathodes

Here, the structural, morphological, and electrochemical performance of Ni-rich LiNi 0.9 Mn 0.05 Al 0.05 O 2 (955NMA) and LiNi 0.85 Mn 0.05 Al 0.1 O 2 (85,510) cathodes strongly depends on the properties of their hydroxide precursors. Ni-Mn-Al hydroxide precursors were synthesized through controlled co-precipitation in a batch stirred tank reactor, where pH, reaction time, metal-ion feed rate, aluminum source, and aluminum concentration were systematically varied to tailor particle morphology, phase composition, and dopant distribution. Two aluminum sources, aluminum nitrate and sodium aluminate produced two distinct hydroxide precursors NMA(OH) 2 -1 and NMA(OH) 2 -2, which were lithiated to form LiNMA1 (Li 0.992 [Ni 0.905 Mn 0.049 Al 0.046 ]O 2 ) and LiNMA2 (Li 0.990 [Ni 0.850 Mn 0.047 Al 0.103 ]O 2 ). Structural and compositional analyses revealed that aluminum incorporation and phase formation in Ni–Mn–Al hydroxides are governed by local supersaturation and interfacial growth kinetics. Rapid dilute aluminum addition produced aluminum-free β-phase hydroxides, intermediate conditions generated mixed α/β phases, whereas slow concentrated dosing enabled uniform aluminum incorporation and stabilization of the β-phase structure. LiNMA1 delivers a high initial discharge capacity of 223 mAhg −1 but significant capacity fading with 67% retention after 100 cycles, associated with structural instability. In contrast, LiNMA2 delivers a lower initial capacity 172 mAhg −1 yet excellent cycling stability 91% retention, attributed to improved TM–O framework stability and reduced cation disorder.

Capacity↗
DOE OSTI2024

Advancing the Performance of Lithium-Rich Oxides in Concert with Inherent Complexities: Domain-Selective Substitutions

Historically, modifications to Li- and Mn-rich (LMR) cathodes have been studied in relation to their efficacy in solving challenges such as oxygen loss and voltage fade, which are inherent to the activation process of these electrodes. However, even in the presence of these phenomena, well-optimized LMR cathodes show considerable promise as earth-abundant options, particularly if other barriers to implementation can be overcome or mitigated. As the complex mechanisms of LMR electrodes are known to stem from the local, chemical inhomogeneities that define the nanocomposite domain nature of these oxides, strategies aimed at manipulating the performance of activated electrodes, irrespective of voltage fade, through domain-selective modifications, could prove instructive. In this work, we use a novel synthesis process aimed at influencing the site occupancy of substituted Sn 4+ , as an example 4+ cation, into a Co-free Li 1.13 Mn 0.57(1–x) Sn 0.57x Ni 0.3 O 2 LMR oxide. We show that Sn 4+ can be selectively substituted into Li-rich environments. The consequences are revealed to be both chemical and morphological, and the domain-selective doping strategy provides a knob for directed control of the low state-of-charge impedance behavior. In conclusion, these results reveal new clues and insights with respect to further advancing the practical relevance of LMR cathode particles and electrodes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Assessing the coating implications of slurry formulations in NCMA and LFMP blend cathodes for lithium-ion batteries

This paper investigates the implications of slurry formulations and electrode processing on the performance of lithium-ion battery (LIB) cathodes, focusing on Nickel Cobalt Manganese Aluminum (NCMA) and Lithium Ferro Manganese Phosphate (LFMP) blends. Through a comprehensive examination of electrode processing steps, from material selection to coating application, we elucidate the critical role of processing parameters in shaping electrode morphology and electrochemical behavior. Rheological studies reveal the influence of slurry composition on viscosity and flow behavior, highlighting the importance of achieving optimal rheological properties for uniform coating deposition. Electrochemical characterization, including cyclic voltammetry and rate capability tests, unveils the electrochemical behavior of NCMA, LFMP, and their blend, showcasing the synergistic effects of material blending on battery performance. In conclusion, our findings underscore the intricate relationship between slurry formulation, electrode processing, and LIB performance, offering valuable insights for the design and optimization of high-performance electrode materials for next-generation batteries.

25 ENERGY STORAGE↗
DOE OSTI2024

Mitigating Calendar Aging in Si-NMC Batteries with Advanced Dual-Salt Glyme Electrolytes

In addressing the critical challenge of calendar aging in silicon (Si)-based lithium-ion batteries, this study introduces a groundbreaking strategy utilizing glyme-type dual-salt electrolytes (lithium bis(trifluoromethanesulfonyl)imide [LiTFSI] and lithium difluoro(oxalato)borate [LiDFOB]). These electrolytes are demonstrated to significantly mitigate parasitic reactions and capacity loss in Si-NMC (lithium nickel manganese cobalt oxide) full cells, especially when compared with traditional carbonate-based electrolytes. Further, our exhaustive mechanistic analysis reveals that such electrolytes not only preserve the integrity of the Si anode but also improve the cathode/electrolyte interphases (CEI) through the formation of a conformal coating on the high-voltage cathode surface. This dual-salt approach, enhanced by the addition of a phosphate additive, effectively decelerates calendar aging, marking a substantial advance in the quest for durable and reliable Si-based energy storage technologies. The findings underscore the vital role of electrolyte composition in extending the calendar life of Si batteries, offering an alternative avenue toward maximizing the performance and longevity of next-generation Li-Si batteries.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Scalable and Highly-Efficient Microbial Electrochemical Reactor for Hydrogen Generation from Wastes

The overall goal of this project was to develop a scalable and highly efficient hybrid microbial electrochemical reactor for hydrogen recovery from waste streams at a cost of less than $\$$2/kg H₂. The specific objectives were: (1) to design and fabricate a scalable and highly efficient microbial electrochemical cell (MEC) reactor, and (2) to determine the techno-economic feasibility of the system for H₂ generation from organic-rich waste streams. We achieved the first objective by (a) developing low-cost electrode materials, (b) synthesizing a highly efficient cathode catalyst in a scalable manner, (c) evaluating and validating the developed electrode material and catalyst in MEC reactors, and (d) designing and fabricating a larger reactor that incorporates (a) to (c). We met the second objective by (a) identifying the impacts of wastewater composition and operational conditions on H₂ production, and (b) developing a cost-performance model that identified critical parameters affecting the system's performance and cost, providing a pathway for further improvement.

08 HYDROGEN↗
DOE OSTI2025

Understanding the Beneficial Role of Transition-Metal Layer Na + Substitution on the Structure and Electrochemical Properties of the P2-Layered Cathode Na 2+ x Ni 2– x /2 TeO 6

Layered Na x MO 2 sodium oxide positive electrode materials have experienced renewed interest owing to the current commercial attention on sodium-ion batteries. Although there are many attractive qualities of these materials, they suffer from serious shortcomings owing to Na + ordering and transition-metal layer gliding that cause a plethora of voltage plateaus during cycling. The P2-layered Na 2+x Ni 2–x/2 TeO 6 (0 ≤ x ≤ 0.5) system provides a framework for investigating the effect of dual Na + substitution into the sodium layer and the transition-metal layer of the structure and its effects on the electrochemical properties of the materials. A careful investigation into the synthesis and properties of these materials reveals that the sodium content used during material preparation has a drastic effect on the composition and electrochemical profile of these materials. The sodium substitution disrupts ordering within the transition-metal layer, thereby disrupting Na + ordering in the adjacent sodium layers. Beyond a critical sodium concentration, the layer stacking shifts, and all voltage plateaus of the P2-Na 2 Ni 2 TeO 6 material are no longer observed at 4.4 V versus Na + /Na. These results also question the common belief that additional sodium precursor is required when preparing layered sodium oxide cathodes, providing new guidelines for material synthesis and characterization.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Multiscale Cryo Electron Microscopy Reveals Interfacial Degradation and Stabilization in Battery Electrodes

Electrochemical interfaces are dynamic systems, evolving based on their local environment and reactant surface structures. The electrode-electrolyte interface in Li-ion batteries can be protective, limiting parasitic reactions with the electrolyte to passivate the surface [1]. Additionally, this interphase has an impact on the Li-ion transport through that layer based on its composition, bonding environment, and thickness. These parameters are challenging to collect and may vary depending on the electrode surface site investigated relative to its spatial position in a coin cell. This study will detail a multiscale cryogenic electron microscopy approach where millimeter-scale cross-sections through the coin cell batteries were made using a cryogenic stage within a fs-laser plasma focused ion beam (laser PFIB) with complementary energy dispersive X-ray spectroscopy able to detect variations in the composition at electrode interfaces [2]. Microscale cross-sectioning and lamella sample preparation of battery electrodes was conducted at the Center for Integrated Nanotechnologies using a Ga-ion focused ion beam (FIB) with air-free and cryo-transfer [3], followed by nanoscale mapping of composition and bonding within the CEI through cryo-scanning transmission electron microscopy (cryo-STEM) electron energy loss spectroscopy [4]. This multiscale approach enabled identification of millimeter-scale features of a battery stack with visualization of degradation in electrodes such as cracks in cathode particles, gas evolution, and SEI evolution; microscale interfacial characteristics, such as heterogeneity in the SEI or barrier layer and identification of electrolyte networks to the electrode surfaces; and nanoscale measurement of the CEI thickness, mapping of transition metal bonding within the cathode particles to identify loss of active materials, and identification of beneficial electrolyte additives incorporated into the CEI structure. This multiscale approach allows for a statistical understanding of the primary mechanisms and parasitic degradation pathways that impact performance by limiting the ion transport pathways within Li+ batteries.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Electrolyte and Cutoff Potential Effects on Cycle Life of Li4Ti5O12/LiNi0.9Mn0.1O2 Batteries for Behind-the-Meter Storage Applications

Behind-the-Meter Storage (BTMS) is a stationary battery energy storage system that is connected to the electrical distribution system on the customer's side of the utility's service meter. BTMS systems are used to store electrical energy from the grid as well as inconstant, renewable energy, such as local solar and wind generation. A successful BTMS system will allow the customer to pair their energy generation and storage to optimize electrical consumption from the grid, improving reliability and minimizing cost. For BTMS applications, batteries must be designed and optimized with different set of criteria from other leading segments of the Li-ion battery market, like transportation, due the system being stationary and proximal to the residential or commercial building it's benefitting. BTMS applications prioritize safety, cost (low/no-critical materials), reliability (20-year calendar life), and durability (10,000 cycle life), while having the ability to (minimally) compromise energy density and rate capability. Lithium titanate (Li4Ti5O12-, LTO) is a promising anode candidate for BTMS applications due to its high safety and capacity retention, while maintaining a reasonable 160 mAhg-1 reversable capacity and composition of relatively abundant materials. (1) Specifically, LTO has a high working voltage which helps to prevent Li dendrite formation, improving safety. Furthermore, LTO also has negligible lithiation-based volume change, leading to less mechanical pulverization, or loss of active material, upon cycling. For the cathode, materials with little or no Co are of high interest due to the high cost and low abundance of Co. LiMn2O4 (LMO) has been paired with LTO for BTMS applications in the past due to its safety, low cost (abundancy), and reasonably high operating voltage. (2-4) However, the low capacity of LMO limits energy density and specific energy. While not the highest priority for BTMS applications, increasing energy density will enable deployment in space constrained BTMS applications and decrease total cost. LiNi0.9Mn0.1O2 (LN-MO) is a recently developed material with promise due to its high operating voltage and relatively low price. (5) However, Ni-rich layered oxides, including LNMO, tend to struggle with capacity retention during high-voltage cycling due to mechanical pulverization, irreversible phase transitions, and unstable solid-electrolyte interphase. The study presented here focuses on building an understanding of how electrolyte solvent and varied cutoff potentials will impact the cycle life of LTO/LN-MO cells. Specifically, a comparison is provided between ethylene carbonate (EC), ethyl methyl carbonate (EMC), fluoroethylene carbonate (FEC), and Gen2 electrolyte solvents with 1M Lithium hexafluorophosphate (LiPF6) salt, cycling to two upper termination potentials, 2.6V and 2.7V. Electrochemical testing and diagnostics (e.g., differential capacity analysis, area specific impedance, constant voltage hold, and rate capability) and post-mortem characterization will be used to understand the aging behavior and failure mechanisms of the 8 cell combinations (four electrolytes and two voltage cutoffs). Cells with FEC electrolyte showed a lower initial capacity compared to cells with Gen2, EMC, and EC cycling at both voltages; however, the cells with FEC showed consistent trends in capacity retention with 2.6V and 2.7V termination potentials, while the cells with the other electrolytes showed much higher rates of capacity loss when cycling to the higher voltage. These results indicate that FEC may play a role in improving durability of high-voltage, Ni-rich electrode systems for use in high-cycle applications, such as BTMS.

electrolyte↗
DOE OSTI2024

Voltage Mining for (De)lithiation-Stabilized Cathodes and a Machine Learning Model for Li-Ion Cathode Voltage

Advances in lithium-metal anodes have inspired interest in discovery of Li-free cathodes, most of which are natively found in their charged state. This is in contrast to today's commercial lithium-ion battery cathodes, which are more stable in their discharged state. In this study, we combine calculated cathode voltage information from both categories of cathode materials, covering 5577 and 2423 total unique structure pairs, respectively. The resulting voltage distributions with respect to the redox pairs and anion types for both classes of compounds emphasize design principles for high-voltage cathodes, which favor later Period 4 transition metals in their higher oxidation states and more electronegative anions like fluorine or polyanion groups. Generally, cathodes that are found in their charged, delithiated state are shown to exhibit voltages lower than those that are most stable in their lithiated state, in agreement with thermodynamic expectations. Deviations from this trend are found to originate from different anion distributions between redox pairs. In addition, a machine learning model for voltage prediction based on chemical formulas is trained and shows state-of-the-art performance when compared to two established composition-based ML models for material properties predictions, Roost and CrabNet.

25 ENERGY STORAGE↗
DOE OSTI2026

Distinct Melt Infusion Architectures of Antiperovskite Solid Electrolytes

Antiperovskite solid electrolytes are an emerging class of lithium‐ion conductors distinguished by their unusually low melting points, enabling scalable, low‐temperature processing routes not accessible to most solid electrolytes. In this work, we synthesize phase‐pure chloride (Cl), bromide (Br), and mixed halide (ClBr) variants of antiperovskites and investigate their ionic conductivities in both powder and hot‐pressed forms. Hot pressing significantly enhances conductivity across all compositions, while energy‐dispersive X‐ray spectroscopy (EDS) of the mixed halide system reveals halide surface migration during densification. We further investigate the melt‐infiltration behavior of these electrolytes into substrates relevant to solid‐state battery architectures, including Al and Cu current collectors, conventional NMC and LFP cathodes, and a foamed NMC cathode with a highly porous architecture. The foamed cathode enables deep and uniform electrolyte penetration, highlighting the role of electrode architecture in facilitating melt infiltration. Across all substrates, electrolyte halide chemistry strongly influences wetting behavior, penetration depth, and resulting microstructural morphology. Together, these results establish clear processing–structure relationships for melt‐infiltrated antiperovskite solid electrolytes and demonstrate how electrolyte chemistry and electrode architecture govern interfacial morphology during integration, providing practical guidelines for processing and structural design in solid‐state battery systems.

antiperovskite↗
DOE OSTI2026

Single-crystal NMC622 from combustion-assisted solid-state synthesis: Tunable particle size, voltage-dependent stability, and Li-ion diffusion

Cost-effective and scalable synthesis of single-crystal lithium–metal-oxide cathodes with controlled size and morphology remains challenging for advancing high-performance lithium-ion batteries. Here, we demonstrate a solution combustion–assisted solid-state method for producing single-crystal NMC622 with tunable particle size at various lithium stoichiometries. Structural and electronic characteristics were probed using synchrotron-XANES, EXAFS, XRD and XPS, confirming well-defined coordination environments and phase purity up to Li ≈ 1.3. The electrochemical behavior of LixNMC (x = 1.0 and 1.3) single crystals was evaluated across 2.8–4.3 V and 2.8–4.7 V windows to elucidate the effects of lithium content and operating voltage. At 2.8–4.3V, Li1.3NMC exhibits higher initial capacity due to its larger lithium inventory, while Li1.0NMC shows superior long-term retention driven by its larger crystal size and reduced structural distortion. Increasing the cutoff voltage to 4.7 V enhances the initial capacity of both compositions by 17–25%, but long-term capacity retention ultimately converges to values comparable to those at 4.3 V due to voltage-induced degradation, where Li+ diffusion constant remains lying ranging from 10−12 –10−11 cm2s−1. Overall, this study establishes a scalable combustion-assisted route for synthesizing tunable single-crystal NMC622 and highlights the interplay between lithium stoichiometry, particle size, and voltage window in governing cathode stability.

Roy, Subrata C [Jackson State University]↗
DOE OSTI2024

Self‐Templated 3D Sulfide‐Based Solid Composite Electrolyte for Solid‐State Sodium Metal Batteries

Abstract Rechargeable solid‐state sodium metal batteries (SSMBs) experience growing attention owing to the increased energy density (vs Na‐ion batteries) and cost‐effective materials. Inorganic sulfide‐based Na‐ion conductors also possess significant potential as promising solid electrolytes (SEs) in SSMBs. Nevertheless, due to the highly reactive Na metal, poor interface compatibility is the biggest obstacle for inorganic sulfide solid electrolytes such as Na 3 SbS 4 to achieve high performance in SSMBs. To address such electrochemical instability at the interface, new design of sulfide SE nanostructures and interface engineering are highly essential. In this work, a facile and straightforward approach is reported to prepare 3D sulfide‐based solid composite electrolytes (SCEs), which utilize porous Na 3 SbS 4 (NSS) as a self‐templated framework and fill with a phase transition polymer. The 3D structured SCEs display obviously improved interface stability toward Na metal than pristine sulfide. The assembled SSMBs (with TiS 2 or FeS 2 as cathodes) deliver outstanding electrochemical cycling performance. Moreover, the cycling of high‐voltage oxide cathode Na 0.67 Ni 0.33 Mn 0.67 O 2 (NNMO) is also demonstrated in SSMBs using 3D sulfide‐based SCEs. This study presents a novel design on the self‐templated nanostructure of SCEs, paving the way for the advancement of high‐energy sodium metal batteries.

Guo, Xiaolin↗
DOE OSTI2025

Influence of AA6061 surface preparation on the resistance to surface degradation of thermally grown boehmite films

Understanding substrate–coating interactions is crucial for designing durable, corrosion-resistant systems. This study investigates the effects of surface treatments— polishing, acid etching, and alkaline etching—on AA6061 aluminum alloy and its thermally grown boehmite coatings. Surface treatments were found to significantly alter boehmite film properties by modifying the alloy’s surface composition. X-ray photoelectron spectroscopy revealed a 10% alumina drop after acid etching alongside chemisorbed species formation in wet treatments. Structural analysis, including grazing incidence X-ray diffraction and TEM, showed α-Al 2 O 3 formation on polished surfaces, improving wear resistance but inducing cathodic E corr shifts, pointing to higher corrosion susceptibility. In contrast, acid and alkaline etching produced anodic E corr shifts with stable, pit-free films observed via potentiodynamic scans. Electrochemical impedance spectroscopy highlighted reduced oxide resistance with extended boehmite growth. The findings emphasize the role of surface pre-treatments and boehmite optimization in balancing durability and corrosion resistance for AA6061 substrates.

AA6061↗
DOE OSTI2026

Structured for success: conjugated polymer binders with tailored composition and architecture for lithium-ion batteries

Conjugated polymer binders are replacing conventional binders in lithium-ion batteries. Herein, we examine how molecular engineering and hierarchical nanostructuring govern binder functionality and electrochemical performance. Lithium-ion batteries (LIBs) are the leading energy storage technology, yet enhancing their energy density and cycle life remains critical. Significant progress has been made in high-capacity anodes and high-voltage cathodes, but their performance is hindered by electrode degradation, where it is related to the behaviors of binders at the surface and interface. Conventional non-conductive binders like poly(vinylidene difluoride) (PVDF), combined with conductive additives, often fail to maintain electrical pathways under repeated volume changes. Alternatively, conjugated polymer binders have emerged as a superior alternative, simultaneously offering intrinsic conductivity, mechanical flexibility, and strong adhesion through π-conjugated backbones and functional groups. Their tunable molecular structure enables efficient electron/ion transport while mitigating electrode cracking. Additionally, the development of hierarchically ordered nanostructures in conjugated polymer binder can further enhance their electrochemical performance. This review examines the design principles of conjugated polymer binders, focusing on molecular engineering and nanostructural control to optimize their performance in high-loading electrodes, such as silicon-based anodes. By addressing key challenges in binder functionality, these advanced materials pave the way for next-generation high-energy-density LIBs.

Jin, Xiuyu↗
DOE OSTI2025

Halide segregation to boost all-solid-state lithium-chalcogen batteries

Mixing electroactive materials, solid-state electrolytes, and conductive carbon to fabricate composite electrodes is the most practiced but least understood process in all-solid-state batteries, which strongly dictates interfacial stability and charge transport. Here, we report on universal halide segregation at interfaces across various halogen-containing solid-state electrolytes and a family of high-energy chalcogen cathodes enabled by mechanochemical reaction during ultrahigh-speed mixing. Bulk and interface characterizations by multimodal synchrotron x-ray probes and cryo–transmission electron microscopy show that the in situ segregated lithium halide interfacial layers substantially boost effective ion transport and suppress the volume change of bulk chalcogen cathodes. Various all-solid-state lithium-chalcogen cells demonstrate utilization close to 100% and extraordinary cycling stability at commercial-level areal capacities.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Microstructure Scale Lithium-Ion Battery Modeling: Part I. On Through-Plane Heterogeneity, Impact of Mesh Representation, and Differences between Macro- and Microscale Models

Li-ion battery performance and degradation are strongly correlated with the electrode microstructures and can be modeled at different scales, each with their own limitations. Herein, we compare predictions achieved with a macro- and a micro-scale model, that is, respectively, neglecting or considering the microstructural heterogeneity of the composite electrodes, on virtual numerically generated and real microstructures. While both models are in relative agreement at the low charge rates, differences arise for fast charging scenarios and especially for the real, highly heterogenous, microstructures. The microscale model predicts that electrolyte concentration saturation and depletion, respectively, at the back of the cathode and of the anode are exacerbated, and that lithium plating occurs earlier for real microstructures. The present work also indicates that the mesh representation significantly impacts the microscale model predictions, and consequently that microscale models should add surface area as a parameter to consider explicitly surface roughness. This article is the first of a series, with subsequent entries further investigating in-plane heterogeneities, lithium plating, and the impact of microstructure representativity on model predictions.

25 ENERGY STORAGE↗
DOE OSTI2025

Entropy-Tailored Fast-Charging Sodium Layered Cathodes

O3-type layered transition metal (TM) oxides are widely used as cathode materials for Na-ion batteries due to their high energy density potential, enabled by the state of charge (SoC)-dependent transition from octahedral (O-type) to prismatic (P-type) structures during Na-ion (de)sodiation. However, the O–P transition is often criticized for compromising the Na-ion mobility and limiting the cycle life. Herein, we reveal the intrinsic correlation between O–P transitions, oxygen behaviors, and Na-ion kinetics. We demonstrate that a compositionally versatile, entropy-tailored approach can promote preferred transitions (characterized by large lattice parameter deviations in the O-type region and rapid O–P biphasic reactions), enhancing Na-ion migration, as revealed by in situ high-energy synchrotron X-ray diffraction (HEXRD). Additionally, irreversible oxygen loss at high SoC is effectively mitigated, while TM migration and surface reconstruction are greatly suppressed, further accelerating Na-ion transport and stabilizing the structure, as confirmed by X-ray absorption spectroscopy (XAS) and theoretical analyses. The result is an exceptionally high rate capability of 88.7 mAh g –1 at 20 C (2.4 A g –1 ) with a superior normalized retention of 72.6%, accompanied by a prolonged lifetime with 74.3% retention after 1000 cycles. In conclusion, this work advances the understanding of the chemistry–property relationships in O3-type layered cathodes and broadens the prospects for fabricating high-power-density electrodes.

36 MATERIALS SCIENCE↗