Nondissipative dc to dc regulator-converter study first quarterly report, 15 jun. - 15 sep. 1964
Nondissipative dc to dc regulator converter or push-pull chopper and push-pull inverter rectifier
CHOPPER↗
SEARCH · Search NASA
Results for “pulling”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Electrothermal fracturing of tensile specimens
Pulling device consisting of structural tube, connecting rod, spring-loaded nuts, loading rod, heating element, and three bulkheads fractures tensile specimens. Alternate heating and cooling increases tensile loading by increments until fracturing occurs. Load cell or strain gage, applied to pulling rod, determines forces applied.
Blinn, H. O.↗
Recombination luminescence in irradiated silicon-effects of uniaxial stress and temperature variations.
Demonstration that luminescence in irradiated silicon consists of a spectral group between 0.80 and 1.0 eV which seems to be independent of impurities, while a lower energy group between 0.60 and 0.80 eV is seen only in pulled crystals. The small halfwidth and temperature dependence of the sharp zero-phonon lines observed in these spectra indicate that the luminescence arises from a bound-to-bound transition. A model is proposed for the transition mechanism. Stress data taken on the 0.79-eV zero-phonon line in pulled crystals can be fit by either a tetragonal 100 (in brackets) defect symmetry or by conduction-band splitting effects. It is suggested that the 0.79-eV zero-phonon line and the 0.60- to 0.80-eV spectral group arise from the EPR G-15 center. Stress data on a zero-phonon line at 0.97 eV associated with the 0.80- to 1.0-eV spectral group can be explained by a trigonal 111 (in brackets) defect. The divacancy is tentatively suggested as responsible for this luminescence spectra.
Jones, C. E.↗
Growth of a single crystal ribbon in space
Three critical technological areas associated with adapting the method of pulling signal crystal silicon ribbon to a space environment were investigated. Basic parameters such as the magnitude of the forces required and the coupling between thermal and force are discussed. The design of a ribbon puller is described, and the problems encountered are also discussed. The force fields in the vicinity of a coil were characterized and results of attempts to pull ribbon are described. The results of the one experiment to grow a conventional float zone crystal in an external static magnetic field are presented.
Padovani, F. A.↗
Improvements in deep-space tracking by use of third-order loops.
Third-order phase-locked receivers have not yet found wide application in deep-space communications systems because the second-order systems now used have performed adequately on past spacecraft missions. However, a survey of the doppler profiles for future missions shows that an unaided second-order loop may be unable to perform within reasonable error bounds. This article discusses the characteristics of a simple third-order extension to present second-order systems that not only extends doppler-tracking capability, but widens the pull-in range and decreases pull-in time as well.
Tausworth, R. C.↗
Third-order phase-locked loop receiver
Third-order extension to present second-order systems extends their Doppler tracking capabilities. It widens receiver pull-in range, decreases pull-in time, lowers voltage-controlled oscillator (VCO) noise (determining when no signal is present), and lessens susceptibility to VCO drift.
Crow, R. B.↗
Power spectral density analysis of the electromyogram from a work task performed in a full pressure suit
Surface electromyograms (EMG) taken from three upper torso muscles during a push-pull task were analyzed by a power spectral density technique to determine the utility of the spectral analysis for identifying changes in the EMG caused by muscular fatigue. The results confirmed the value of the frequency analysis for identifying fatigue producing muscular performance. Data revealed reliable differences between muscles in fatigue induced responses to various locations in the reach envelope at which the subjects were required to perform the push-pull exercise, and the differential sensitivity of individual muscles to the various reach positions; i.e., certain reach positions imposed more fatigue related shifts in EMG power than did others. It was found that a pressurized space suit changed the pattern of normal shirtsleeve muscle fatigue responses in all three of the muscles.
Lafevers, E. V.↗
Low-cost tool set for removing brazed fittings
Set includes crimping tool and pull tube. Crimping tool is modified vise-grip pliers which has special jaws designed to crimp fittings. Pull tube has single thread on each end. Tube can be used once on each end before discarding.
Giandomenico, A.↗
A stable, linear frequency-modulated oscillator, part 1
The development of a push-pull frequency-modulated oscillator employing field-effect transistors is described. The advantages of field-effect transistors for use in a frequency-stable oscillator are presented. Linearization of the frequency deviation was accomplished by utilizing the square-law characteristic of an FET used as a modulating amplifier. The push-pull oscillator model produced a linear frequency deviation of more than 10 MHz at a center frequency of approximately 100 MHz. Output power is within 0.6 db of a nominal +8.5 dBm over the desired frequency range, and the modulation bandwidth is dc to 10 MHz. Frequency variation with temperature after compensation with a negative-temperature-coefficient capacitor is within + or - 0.05% from 0 to 60 C.
Honnell, M. A.↗
Evaluation of localized muscle fatigue using power spectral density analysis of the electromyogram
Surface electromyograms (EMGs) taken from three upper torso muscles during a push-pull task were analyzed by a power spectral density technique to determine the operational feasibility of the technique for identifying changes in the EMGs resulting from muscular fatigue. The EMGs were taken from four subjects under two conditions (1) in shirtsleeves and (2) in a pressurized space suit. This study confirmed that frequency analysis of dynamic muscle activity is capable of providing reliable data for many industrial applications where fatigue may be of practical interest. The results showed significant effects of the pressurized space suit on the pattern of shirtsleeve fatigue responses of the muscles. The data also revealed (1) reliable differences between muscles in fatigue-induced responses to various locations in the reach envelope at which the subjects were required to perform the push-pull exercise and (2) the differential sensitivity of muscles to the various reach positions in terms of fatigue-related shifts in EMG power.
Lafevers, E. V.↗
Dip coating process: Silicon sheet growth development for the large-area silicon sheet task of the low-cost silicon solar array project
To date, an experimental dip-coating facility was constructed. Using this facility, relatively thin (1 mm) mullite and alumina substrates were successfully dip-coated with 2.5 - 3.0 ohm-cm, p-type silicon with areas of approximately 20 sq cm. The thickness and grain size of these coatings are influenced by the temperature of the melt and the rate at which the substrate is pulled from the melt. One mullite substrate had dendrite-like crystallites of the order of 1 mm wide and 1 to 2 cm long. Their axes were aligned along the direction of pulling. A large variety of substrate materials were purchased or developed enabling the program to commence a substrate definition evaluation. Due to the insulating nature of the substrate, the bottom layer of the p-n junction may have to be made via the top surface. The feasibility of accomplishing this was demonstrated using single crystal wafers.
Heaps, J. D.↗
Web-dendritic ribbon growth
A web furnace was constructed for pulling dendritic-web samples. The effect of changes in the furnace thermal geometry on the growth of dendritic-web was studied. Several attempts were made to grow primitive dendrites for use as the dendritic seed crystals for web growth and to determine the optimum twin spacing in the dendritic seed crystal for web growth. Mathematical models and computer programs were used to determine the thermal geometries in the susceptor, crucible melt, meniscus, and web. Several geometries were determined for particular furnace geometries and growth conditions. The information obtained was used in conjunction with results from the experimental growth investigations in order to achieve proper conditions for sustained pulling of two dendrite web ribbons. In addition, the facilities for obtaining the following data were constructed: twin spacing, dislocation density, web geometry, resistivity, majority charge carrier type, and minority carrier lifetime.
Hilborn, R. B., Jr.↗
Corps of Engineers applications for remote sensing of the environment
An objective overview is presented of the application of remote sensing technology in the Corps of Engineers. Examples are given of attempts to use the current state of the art to achieve particular disciplinary or mission oriented goals. The Corps, presently engaged in both research and development and technology transfer, has encountered some interesting situations. Practical operational utilization depends not only on technology, but also economic benefit/cost factors and some unprecedented legal, political, and social issues. Yet, at a time when increased agency commitment to operational usage is being sought, an assessment of the state of the art reveals that sensor technology, data processing and analysis, and models still require further development. There is a challenge in synchronizing technology push with the demand pull of dimly perceived user needs. They should complement each other rather than oppose. The goal is to use the combined push-pull effect to lead to increased productivity and responsiveness by the Corps.
Kurtz, M. K., Jr.↗
Development of advanced methods for continuous Czochralski growth. Silicon sheet growth development for the large area silicon sheet task of the low cost silicon solar array project
The three components required to modify the furnace for batch and continuous recharging with granular silicon were designed. The feasibility of extended growth cycles up to 40 hours long was demonstrated by a recharge simulation experiment; a 6 inch diameter crystal was pulled from a 20 kg charge, remelted, and pulled again for a total of four growth cycles, 59-1/8 inch of body length, and approximately 65 kg of calculated mass.
Wolfson, R. G.↗
Theoretical analysis of heat flow in horizontal ribbon growth from a melt
A theoretical heat flow analysis for horizontalribbon growth is presented. Equations are derived relating pull speed, ribbon thickness, thermal gradient in the melt, and melt temperature for limiting cases of heat removal by radiation only and isothermal heat removal from the solid surface over the melt. Geometrical cross sections of the growth zone are shown to be triangular and nearly parabolic for the two respective cases. Theoretical pull speed for silicon ribbon 0.01 cm thick, where the loss of latent heat of fusion is by radiation to ambient temperature (300 K) only, is shown to be 1 cm/sec for horizontal growth extending 2 cm over the melt and with no heat conduction either to or from the melt. Further enhancement of ribbon growth rate by placing cooling blocks adjacent to the top surface is shown to be theoretically possible.
Zoutendyk, J. A.↗
Installing fiber insulation
A method for installing fragile, high temperature insulation batting in an elongated cavity or in a resilient wire sleeve to form a resilient seal. The batting is preformed to rough dimensions and wrapped in a plastic film, the film being of a material which is fugitive at a high temperature. The film is heat sealed and trimmed to form a snugly fit skin which overlaps at least at one end to permit attachment of a pull cord. The film absorbs the tensile force of pulling the film enclosed batting through the cavity or wire mesh sleeve and is subsequently driven off by high temperature baking, leaving only the insulation in the cavity or wire mesh sleeve.
Wang, D. S.↗
An experimental investigation of silicon wafer surface roughness and its effect on the full strength of plated metals
Plated silicon wafers with surface roughness ranging from 0.4 to 130 microinches were subjected to tensile pull strength tests. Electroless Ni/electroless Cu/electroplated Cu and electroless Ni/electroplated Cu were the two types of plate contacts tested. It was found that smoother surfaces had higher pull strength than rougher, chemically etched surfaces. The presence of the electroless Cu layer was found to be important to adhesion. The mode of fracture of the contact as it left the silicon was studied, and it was found that in almost all cases separation was due to fracture of the bulk silicon phase. The correlation between surface roughness and mode of contact failure is presented and interpreted.
Spiers, G. D.↗
Oxide Control for Silicon Crystal Growth
Web dendrite growth process pulls sheet of newly crystallized silicon from molten silicon. Jets of argon pull outside gas into melt cavity, preventing silicon oxide from passing through heat-shield hold and depositing on it. Generated by aspirators, reversed flow is used in web dendrite process, which produces sheets of single-crystal silicon for low-cost solar cells.
Wehrli, H. A. I.↗