Search NASA⌕ Search

SEARCH · Search NASA

Results for “in situ formed polymer-based catholytes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

2,860 records · Page 99
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Cr plasma-material-interaction in PISCES-RF: D thermal release, retention, and erosion

Pure chromium (Cr) targets were exposed to high-flux deuterium (D) plasmas in the Pisces-RF linear plasma device, and measurements of D retention, release, and erosion were subsequently performed. Post-exposure D retention was quantified using temperature-programmed desorption on Cr targets irradiated by 50 eV ions over a broad range of exposure temperatures (423–873 K) and ion fluences (3 × 10 24 – 3 × 10 26 m −2 ). The retained D inventory was observed to decrease rapidly with increased exposure temperature, from approximately ∼7 × 10 20 m −2 at ∼ 420 K, to then saturate near ∼ 10 20 m −2 for exposure temperatures above ∼550 K. Separately, at fixed exposure temperature (∼450 K), D retention was found to have only a weak dependence on increasing ion fluence. Lastly, the erosion of Cr in D plasma was investigated for ion impact energies in the range 40 ≤ E i ≤ 250 eV. Erosion was inferred using optical emission spectroscopy (OES) from the ratio of emission lines (Cr I (425.4 nm)/D I (656.1 nm)) measured close to the target. Conversion of the OES yield data to net erosion yield was made with singular ion energy target mass-loss measurements. These net erosion yield data were then further corrected to obtain gross erosion yield by accounting for a re-deposition factor, computed using a simple model. The gross erosion yield is found to be 2–4 times lower than predicted by SDTrimSP, consistent with that typically observed for light-ion sputtering under high-flux plasma conditions.

Chromium↗
NASA NTRS1996

Space Photovoltaic Research and Technology 1995

The Fourteenth Space Photovoltaic Research and Technology conference was held at the NASA Lewis Research Center from October 24-26, 1995. The abstracts presented in this volume report substantial progress in a variety of areas in space photovoltaics. Technical and review papers were presented in many areas, including high efficiency GaAs and InP solar cells, GaAs/Ge cells as commercial items, high efficiency multiple bandgap cells, solar cell and array technology, heteroepitaxial cells, thermophotovoltaic energy conversion, and space radiation effects. Space flight data on a variety of cells were also presented.

Geoffrey Landis↗
NASA NTRS1981

Bipolar battery construction

A lightweight, bipolar battery construction for lead acid batteries in which a plurality of thin, rigid, biplates each comprise a graphite fiber thermoplastic composition in conductive relation to lead stripes plated on opposite flat surfaces of the plates, and wherein a plurality of nonconductive thermoplastic separator plates support resilient yieldable porous glass mats in which active material is carried, the biplates and separator plates with active material being contained and maintained in stacked assembly by axial compression of the stacked assembly. A method of assembling such a bipolar battery construction.

Rippel, Wally E.↗
DOE OSTI2025

Interleaved bond frustration in a triangular lattice antiferromagnet

Frustration of long-range order via lattice geometry amplifies fluctuations and generates ground states that are highly sensitive to perturbations. Traditionally, geometric frustration is used to engineer unconventional magnetic states; however, the charge degree of freedom and bond order can be similarly frustrated. Finding materials that host both frustrated magnetic and bond networks holds promise for engineering structural and magnetic states with the potential of coupling to one another via either magnetic or strain fields. Here we identify an unusual instance of this coexistence in the triangular lattice antiferromagnets LnCd 3 P 3 (Ln = lanthanides). These compounds feature two-dimensional planes of unique trigonal planar CdP 3 units with an underlying bond instability that is frustrated via emergent kagome ice correlations. This bond instability is interleaved in between layers of frustrated magnetic moments. Furthermore, our results establish LnCd 3 P 3 as a rare materials class in which frustrated magnetism is embedded within a dopable semiconductor with a frustrated bond order instability.

Gomez Alvarado, S. J. [University of California, S↗
DOE OSTI2026

Identifying Strain Stacking Boundaries between Multiphase Domains in Atomically Thin Two-Dimensional Magnets

Stacking engineering of van der Waals materials is an important strategy to control the materials’ properties, such as electronic correlations, ferroelectricity, and layer-dependent two-dimensional magnetism. A timely testbed for the study of the latter is atomically thin chromium trihalides (CrX 3 , X = Cl, Br, I). Notably, by understanding the sliding mechanism between different stacking sequences, control of the stacking arrangement, and thus magnetic properties in CrX 3 , can be achieved. Such insight, however, is currently lacking. Here, in this study, advanced electron microscopy methods are used to identify multiple stacking sequences corresponding to different bulk phases in atomically thin CrX 3 (X = Cl and Br) down to bilayer thickness and with lateral domain sizes as small as tens of nanometers. Indications of nanometer scale transitions and interactions at the stacking boundaries are found, including a universally preferred sliding direction that is consistent with density functional theory calculations and the strain fields at lateral heterostructure boundaries. This study demonstrates the necessity to consider local stacking structures when interpreting averaged magnetic properties measured with macroscale probes. Additionally, the preferred sliding direction insight from this study provides a strategy to control stacking sequence in atomically thin CrX 3 samples during the exfoliation and sample fabrication process.

DFT calculations↗
DOE OSTI2026

Proteome-wide analysis of protein stability in Escherichia coli under acid stress

Knowledge of protein acid sensitivity remains sparse and is largely derived from low-throughput, enzyme-specific assays. We used a scalable framework to map acid stability across the Escherichia coli proteome to assess the acid stability of 1,675 unique proteins, estimating pH 50 values for over 90% of them. The parameter pH50 was defined as the pH value at which only 50% of the initial protein remains in solution following acid treatment. Proteome-wide pH 50 values ranged from 2.28 to 6.33 (median 5.11). Approximately 9% of detected proteins remained stable across all tested pH conditions. Our results align with published data and the assay of citrate synthase (GltA) performed here. Protein acid stability differed significantly by subcellular localization: periplasmic proteins were relatively more abundant in the acid-stable group, cytoplasmic proteins were abundant at pH 50 values 4.5–5.5, and inner membrane proteins at higher pH 50 between 5.5 and 6.0. Outer membrane proteins were too few to draw strong conclusions regarding enrichment within specific pH 50 groups. Notably, the periplasmic binding protein of the molybdate ABC transporter (ModA), was enriched after incubation at low pH. Estimated pH 50 values showed no correlation with protein isoelectric point and molecular weight. Together, this work provides the first proteome-wide map of protein acid stability and establishes a general framework for studying different chemical stressors.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Challenges and Opportunities for HVAC + Phase Change Material Thermal Energy Storage in Buildings

Phase-change material (PCM) thermal-energy storage (TES) integrated with HVAC and domestic hot water (DHW) can shift a large share of building thermal loads. By flattening and shifting loads, PCM TES reduces peak electricity use, eases stress on local and grid infrastructure, and lowers costs. It can also defer costly upgrades to service panels, distribution, and transmission. Higher energy density relative to chilled or hot water storage makes PCM TES practical for small, space limited, and retrofit projects, while packaged HVAC-integrated systems expand cost-effective load shifting to commercial buildings that previously lacked options. Despite this promise, deployment faces barriers. This paper presents challenges, opportunities, and lessons learned from lab and field integrations of PCM TES with packaged HVAC systems. Key challenges include misalignment between default heat pump controls tuned for direct-to-load operation and TES charge/discharge objectives, PCM properties that diverge from manufacturer claims and evolve with cycling, and high integration and deployment costs with off-the-shelf products. These studies underscore the need for factory built, integrated systems that arrive as prepackaged modules with proven controls, reducing design and installation effort and delivering predictable performance across projects. The paper outlines steps to enable viable and scalable PCM TES HVAC and DHW systems, including 1) validated methods that can be used to characterize PCM properties and TES system performance, 2) supervisory controls that optimize charge/discharge scheduling, and 3) factory integrated packaging that eliminates bespoke field engineering.

Dutton, Spencer↗
DOE OSTI2025

Field-tunable BKT and quantum phase transitions in spin-$\frac{1}{2}$ triangular lattice antiferromagnet

Quantum magnetism is one of the most active fields for exploring exotic phases and phase transitions. The recently synthesized Na 2 BaCo(PO 4 ) 2 (NBCP) is an ideal material incarnation of the spin-$\frac{1}{2}$ easy-axis triangular lattice antiferromagnet (TLAF). Experimental evidence shows that NBCP hosts the spin supersolid state with a giant magnetocaloric effect. Theory further predicts that magnetic fields can drive NBCP through Berezinskii-Kosterlitz-Thouless (BKT) and other richer quantum phase transitions. However, detecting these transitions is challenging, as they onset at ultralow temperatures near 60 mK and require high magnetization sensitivity. Using a newly developed gradient force magnetometer in a dilution refrigerator, we mapped the magnetic susceptibility phase diagram down to 30 mK. Our results provide a more comprehensive and accurate understanding of BKT melting of spin supersolidity and several field-tunable quantum phase transitions, which establish NBCP as a model platform for frustrated magnetism and highlight potential applications of its giant magnetocaloric effects.

BKT transition↗
DOE OSTI2026

Tuning Anisotropic Optical Properties of Inorganic and Hybrid Organic–Inorganic MXenes via Topochemical Surface Modification

Surface groups are central to the properties of MXenes, yet their role in optical anisotropy remains largely unexplored. Here, we use a topochemical route to synthesize single crystals of stacked Ti 3 C 2 Cl 2 and hybrid organic–inorganic MXenes (h-MXenes) with lateral sizes of 38–75 μm, rotational registry, and tunable interlayer spacing. Solid-state NMR spectroscopy shows that topochemical substitution generates mixed amido, imido, and hydride surface motifs, which modify the electronic structure of the Ti 3 C 2 inorganic core. Imaging spectroscopic ellipsometry with micron-scale spatial resolution enables reconstruction of the complex dielectric tensor of individual multilayer crystals. Ti 3 C 2 Cl 2 exhibits a type-II hyperbolicity above 930 nm, whereas h-MXenes do not display hyperbolicity within the measured 300–1700 nm window, instead showing reduced in-plane conductivity, suppressed out-of-plane light absorption, and a chain-length-dependent blue shift of a near-infrared absorption feature. These results demonstrate topochemical surface modification as a direct handle for engineering MXenes as surface-programmable optical media.

Hybrid materials↗
DOE OSTI2026

Flame stabilization in DME spray flames under engine-relevant conditions characterized by OH* chemiluminescence and formaldehyde laser-induced fluorescence

The transient and quasi-steady flame structures of Dimethyl Ether (DME) fuel sprays, produced by a single-hole injector (Spray D), were investigated using Planar Laser-Induced Fluorescence (PLIF) and chemiluminescence imaging in a constant-volume chamber under Engine Combustion Network (ECN) Spray A conditions (900 K ambient temperature, 60 bar ambient pressure, 1500 bar injection pressure, and 22.8 kg/m 3 ambient density). Low-temperature chemical reaction zones were visualized using formaldehyde (CH 2 O) PLIF with 355 nm excitation, while high-temperature flame regions were captured via chemiluminescence imaging of excited-state hydroxyl radicals (OH*). Both transient and quasi-steady flame structures clearly show the transition from CH 2 O to OH*, highlighting the progression from low- to high-temperature combustion, while the position of the flame is displaced for DME compared to reference hydrocarbon n-dodecane. Homogeneous reactor calculations with detailed chemistry and using adiabatic mixing for initial temperature show that CH 2 O peaks are significantly higher for DME at the same equivalence ratio, with a higher heat-release during the cool-flame regime with respect to the fuel heating value. Thus, the cool-flame dynamic as a precursor to high-temperature combustion and flame stabilization exhibit distinct behavior for DME relative to conventional hydrocarbons, and these phenomena are effectively resolved through the soot-free nature of DME and the high-speed, time-resolved diagnostics.

CH2O laser-induced fluorescence↗
DOE OSTI2026

Neutron detector response modeling in NOvA

Neutrons can present a significant challenge for neutrino experiments in which energy reconstruction is critical. With the ability to escape detection completely and with a weak correlation between their kinetic energy and any eventual energy deposition, it is difficult to fully account for neutrons produced in neutrino interactions. This in turn leads to significant model dependence when evaluating neutron-related systematic uncertainties. The NOvA experiment is a long-baseline neutrino oscillation experiment with a high-statistics sample of antineutrino data collected by its near detector. We report an excess relative to data of simulated neutron candidates with low energy depositions when using standard Geant4 physics lists. The simulation excess is traced to an overabundance of secondary photons produced from interactions of neutrons with kinetic energy greater than \SI{20}{\mega\eV}. Improved agreement with data is obtained by applying the data-driven neutron-on-carbon \menate model for neutrons between \SI{20}{\mega\eV} and ${\sim}$\SI{100}{\mega\eV}. With \menate, the residual oversimulation is more uniform across the calorimetric neutron energy spectrum, suggesting possible overproduction of primary neutrons by the GENIE neutrino interaction generator. These results motivate the adoption of \menate-supplemented Geant4 simulation as the nominal simulation in the production of future \nova simulation.

Abubakar, S.↗
DOE OSTI2025

Dimensional Evolution Guides Property Control in the A n Cu 4– n TiS 4 Semiconductor Series

Through progressive reduction of the three-dimensional (3D) covalent network of Cu 4 TiS 4 , we isolate seven new members of the A n Cu 4–n TiS 4 family (A = alkali metal; n = 0–4), spanning 3D, 2D, 1D, and 0D structural fragments. The dimensional reduction is rational, as it preserves the edge-sharing connectivity between [CuS 4 ] 7– and [TiS 4 ] 4– tetrahedra across the series. This structural evolution is driven by the stepwise substitution of Cu with alkali metals, guiding the formation of fragments with reduced dimensionality. The effects of “n” and “A” on the crystal structures, stabilities, electronic structures, and optoelectronic properties are profound, demonstrating that the manipulation of alkali metal size and A n Cu 4–n TiS 4 stoichiometry enables predictable variations in structure and properties. For example, the n = 0 and n = 4 end members of the A n Cu 4–n TiS 4 family set the range of achievable band gaps with 2.00 eV for Cu 4 TiS 4 , 2.60 eV for Na 4 TiS 4 , and intermediate values for the n = 1–3 members. Notably, CsCu 3 TiS 4 exhibits exceptional air stability and congruent melting, with density functional theory (DFT) calculating moderate hole and electron effective masses in specific crystallographic directions (mh = 1.24m 0 , me = 0.87m 0 ). Additionally, A 3 CuTiS 4 (A = Na, K, Rb) displays direct band gap behavior and long photoluminescence lifetimes of 2.3–8.6 μs, and K 3 CuTiS 4 has a PLQY of 5.19%. These findings underscore the potential of the A n Cu 4–n TiS 4 family for applications in optoelectronics and demonstrate widely applicable design concepts that unveil rational stoichiometries within a given composition space to generate a series of crystal structures related through an evolving covalent dimensionality that corresponds to a predictable electronic structure and property progression.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1981

Synthetic battery cycling

The trend in energy storage is toward systems with high-voltage and high-power outputs. These conditions accentuate the cumulative effects of small differences in characteristics from cell to cell in any large multicell battery. These considerations are of particular concern with a number of emerging electrochemical concepts where convenient overcharge reactions do not exist. The use of interactive computer graphics is suggested as an aid in battery system development. Mathematical representations of simplistic but fully representative functions of many electrochemical concepts of current practical interest will permit battery-level charge and discharge phenomena to be analyzed in a qualitative manner prior to the assembly and testing of actual hardware. This technique will be a useful addition to the variety of tools available to the battery system designer as he bridges the gap between interesting single-cell life test data and reliable energy storage subsystems.

Thaller, L. H.↗
NASA NTRS2005

Chapter 19A – Radar Cross Section

The material in this Section will provide the novice Flight Test Engineer (FTE) with a brief overview of the radar cross section (RCS) concept. Brief details of radar range descriptions, operations, target calibrations, and data reduction are included. It is noted that these range operations concentrate on the "static" test range rather than the much more sophisticated "dynamic" test range. The dynamic test range is what the FTE will probably work with. Radar reflectivity measurement has developed over the last two decades from a relatively simple endeavor involving the measurement of target RCS amplitude statistics to involving wide band, coherent systems that can measure high resolution images of targets as well as, in many cases, the polarization and phasing properties. This rapid growth in RCS technology has occurred because of the increased use of radar in today's commercial and military systems. In general, the goal for commercial systems is to enhance radar reflectivity, whereas the military goal is to reduce radar reflectivity. Also, classification and identification are important for military purposes because in adverse weather radar may be the only system that may be capable of separating enemy targets from friendly ones. This Section will discuss the fundamentals of RCS. Since the flight test techniques associated with RCS measurements are very similar to those of antenna pattern measurements, both will be presented at the same time in Section 19B Antenna Radiation Pattern Measurements.

Robert W Borek↗
DOE OSTI2025

Review on Preprocessing Strategies, Deactivation, Thermal Safety, and Future Perspectives in Lithium-Ion Battery Recycling

The rapid growth in the use of lithium-ion batteries (LIBs) in electric vehicles, consumer electronics, and renewable energy storage has made effective end-of-life management essential. Recycling LIBs is critical not only for resource recovery and environmental protection but also for ensuring safety and economic viability. This review focuses on the preprocessing technologies that precede typical recovery processes, including disassembly, sorting, discharging, electrolyte removal, dismantling, thermal treatment, separation, and flotation. These steps play a foundational role in determining the efficiency, safety, and environmental impact of LIB recycling. LIBs pose substantial fire and explosion risks due to residual charge, flammable electrolytes, and reactive materials. The conditions and successive progression of the exothermic reactions which lead to thermal runaway has been discussed. It also explores secure deactivation techniques such as external circuit discharge, saline immersion, and thermomechanical methods, alongside fire prevention strategies including the use of flame retardants, elimination of oxidants, and reduction of heat generation and accumulation. Challenges and future directions are outlined, highlighting the need for standardized designs, automation, and safer, more sustainable recycling infrastructure. Furthermore, this review is distinguished by its focused analysis of preprocessing and deactivation steps, with particular attention to the thermal safety engineering aspects of LIB recycling.

Battery deactivation↗
DOE OSTI2025

Chiral edge state control of thermoelectric effects

Thermoelectric responses in two-dimensional electron gases subjected to magnetic fields have the potential to provide unique information about quasiparticle statistics. In this study, we show that chiral edge states play a key role in thermoelectric Hall bar measurements by completely controlling the direction of the internal thermal gradient. To this end, we perform measurements of the magnetothermoelectric responses of cadmium arsenide quantum wells. The magnetothermoelectric responses in the quantum Hall regime agree with theoretical predictions if one considers the role of chiral edge states, which flow in opposite directions on either side of the Hall bar and establish an internal temperature gradient that is perpendicular to the externally applied thermal gradient. We show that the results are self-consistent within this picture under different measurement conditions. We discuss potential applications of the findings, such as in nanoscale control of local temperature gradients and thermoelectric effects along with the characterization of other topological systems with chiral edges states.

Science & Technology - Other Topics↗
NASA NTRS1979

The 60-MW Shuttle Interaction Heating Facility

An arc-heated wind-tunnel system described in the present paper will simulate aerodynamic heating in large-scale tests of the thermal protection system of the Shuttle Orbiter Vehicle during entry. The system provides for large-scale subsystem tests in high-enthalpy streams with boundary layer flows at high Reynolds numbers and for large test-body sizes in stagnation flows. The discussion covers the design concept of the arc-jet systems, the extensive hardware developments of the arc heater to provide reliable operation, and verification and performance measurements of the system's operating envelopes.

W Winovich↗