Search NASA⌕ Search

SEARCH · Search NASA

Results for “Novel Processing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Technoeconomic Analysis of a Microwave-Assisted Novel Process That Converts Polypropylene Plastic Waste to Propylene

Propylene is an important petrochemical that is used in various industries, including the automobile and polymer sectors. Conventionally, propylene has been produced through fluid catalytic cracking, steam cracking, and propane dehydrogenation. In this project, a novel process to produce propylene from polypropylene plastic waste using a microwave reactor is introduced. Propylene production is simulated in Aspen Plus for both the conventional propane dehydrogenation process and the novel design, with heat integration applied to minimize utility demands and the conventional process serving as the base case for comparison. Finally, a tailored technoeconomic analysis is carried out for both simulated cases to estimate important economic indicators. Analysis of the results shows that the novel microwave-assisted process outperforms the conventional route for propylene production, achieving a single-pass conversion of almost 100%, compared with only 33.8% in the conventional plant. The Net Present Value of the novel plant is $\$1720.3$ MM, which is 3.5 times higher than the conventional process, while the Levelized Cost of Propylene is reduced by 40%. Capital and operating expenditure are also improved in the proposed scheme, with reductions of approximately $\$29$ MM and $\$222$ MM/yr, respectively. In addition to cost savings, this novel process also provides a convenient means to recycle waste polypropylene.

42 ENGINEERING↗
DOE OSTI2022

Low-Cost Recyclable Oxygen Carrier and Novel Process for Chemical Looping Combustion

The University of North Dakota, through its Institute for Energy Studies and Energy & Environmental Research Center, partnered with Envergex LLC, Barr Engineering and Microbeam Technologies to develop a transformational enabling technology for advancement of Chemical Looping Combustion technology. Industrial support was provided by Carbontec Energy Corporation. The project targeted the two biggest challenges to chemical looping combustion: (1) High costs of oxygen carrier replacement/loss due to expensive manufacturing and high replacement rates from physical attrition and/or decrease in reactivity, and (2) Inherently slow fuel char conversion which represents the rate-limiting step for chemical looping combustion and results in very large equipment sizes, and overall lower carbon dioxide capture efficiency. The project activities were addressed in a series of seven tasks. Task 1 extended throughout the entire project and oversaw project management and execution. Task 2 and 3 focused on development and evaluation of the novel oxygen carrier. Task 4 to 7 focused on design of the novel reactor, testing with the novel oxygen carrier and a techno-economic assessment of the process. The list of tasks are: Task 1 – Project management and planning, Task 2 – Laboratory scale oxygen carrier manufacturing and assessment, Task 3 – Modeling and laboratory-scale evaluation of oxygen carrier performance with coal, Task 4 – 10-kilowatt thermal integrated system installation, Task 5 – Scaled-up oxygen carrier manufacturing, Task 6 – 10-kilowatt testing, and Task 7 – Process design and techno-economic analysis.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2022

Novel processing route for design and manufacturing of metal toughened nanoceramics: Al–Al 2 O 3 nanocermets

Monolithic alumina is a highly brittle ceramic with a very low fracture toughness, making it an unreliable material for mechanical and structural applications. Ceramic-metal composites (cermets) are the subject of intensive interest to obtain materials which can address the intrinsic brittleness of ceramics without compromising their high strength and light weight. In the present investigation, aluminium-alumina (Al–Al 2 O 3 ) nanocermets were developed. The nanocermets possessed the toughness of Al phase and the strength of reinforced nano Al 2 O 3 particles. Here, the nanocermets green bodies were prepared such that upon sintering each adjacent Al 2 O 3 grain was conformally coated with a continuous Al film. Mechanical milling via a combination of cryo-milling and ball-milling was used to prepare Al–Al 2 O 3 nano-powder mixture. Spark plasma sintering was used to consolidate the green nanocermets. Results show that specimens prepared from 35 h milled powders exhibited superior mechanical properties as compared to other nanocermets, with an improvement in microhardness, elastic modulus, compressive strength, and flexural strength by 88%, 78%, 69% and 40% with respect to sintered pure Al. The indentation toughness of 35 h milled nanocermet showed an increment of 12.5% with respect to sintered pure Al 2 O 3 . Characterization techniques such as XRD, SEM, HR-TEM, X-ray tomography were employed to investigate the phase evolution and structural morphology, while FEM simulations were performed for understanding the crack propagation mechanisms in nanocermets.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Novel Process for Screen-Printed Selective Area Front Polysilicon Contacts for TOPCon Cells Using Laser Oxidation

The efficiency potential of double-side tunnel oxide passivated contact (DS-TOPCon) solar cells is limited by parasitic absorption in the front poly-Si layer, despite excellent passivation and high V OC . The use of patterned poly-Si only under the front metal grid lines can significantly reduce the parasitic absorption loss without sacrificing voltage. In this work, we demonstrate a simple, manufacturing-friendly method of patterning the front poly-Si using a nanosecond UV (355 nm) laser. We found that with laser powers ≥3 W at a 400 mm/s scan speed, an estimated 1–4 nm thick stoichiometric SiO 2 layer was grown on TOPCon. This served as a mask for KOH-etching of 200 nm poly-Si, allowing for patterning of poly-Si fingers required for selective TOPCon. While laser powers above 3 W caused substantial deterioration in passivation quality, the resulting damage in J 0 was largely recovered by subsequent PECVD SiN x deposition. At 3 W, the full area J 0 was found to be 36.8 fA·cm –2 . Furthermore, this translates to 1.68 fA·cm –2 for 4.48% coverage from the wing area of the polyfinger lines (100 lines–100 μm wide and 30 μm metal) contributing to a total front J 0 of ~10 fA·cm –2 , well suited for 25% efficient solar cells

42 ENGINEERING↗
DOE OSTI2022

Atoms to fibers: Identifying novel processing methods in the synthesis of pitch-based carbon fibers

Understanding and optimizing the key mechanisms used in the synthesis of pitch-based carbon fibers (CFs) are challenging, because unlike polyacrylonitrile-based CFs, the feedstock for pitch-based CFs is chemically hetero- geneous, resulting in complex fabrication leading to inconsistency in the final properties. In this work, we use molecular dynamics simulations to explore the processing and chemical phase space through a framework of CF models to identify their effects on elastic performance. The results are in excellent agreement with experiments. We find that density, followed by alignment, and functionality of the molecular constituents dictate the CF mechanical properties more strongly than their size and shape. Last, we propose a previously unexplored fabrication route for high-modulus CFs. Unlike graphitization, this results in increased sp 3 fraction, achieved via generating high-density CFs. In addition, the high sp 3 fraction leads to the fabrication of CFs with isometric compressive and tensile moduli, enabling their potential applications for compressive loading.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2022

A Novel Process for Converting Coal to High-Value Polyurethane Products

Battelle has demonstrated a patented process for making high-value, polyurethane (PU) foam from coal, based on preparing liquefied coal via direct liquefaction, converting it to polyols as an intermediate via ozonation, and then making PU foams from these polyols. This process represents a breakthrough in innovative utilization of U.S. coals, and is applicable to bituminous as well as sub-bituminous coals. The resulting PU foam products are projected to have an extremely high value (i.e., over $\$5,000$ /ton), with nearly 100% of carbon utilization from coalderived liquid feedstock, and 31.5% to 43.5% of the carbon in the PU foam polyol product being bio-based. The targeted products represent an extremely large (i.e., over $80 billion/year), existing PU foam market, which could expand into making coatings and adhesives. The process can further help reduce petroleum imports, while improving the economics of PU foam production. This work was completed with funding from the National Energy Technology Laboratory (NETL), with cost share from the State of Ohio’s Ohio Development Services Agency (ODSA) and others, and has advanced the process to 10 kg/day continuous scale and thus to Technology Readiness Level (TRL) 5. A total of 48 coal-based polyols were prepared and evaluated. The initial 28 polyols focused on range finding for ideal conditions. The later 20 polyols were produced as part of process optimizations. These optimizations were targeted around a continuous ozonolysis process to evaluate extended time reactions and to create the necessary intermediate for production of 1-gallon samples of polyol. The most unique attribute of Battelle’s polyol is in the utilization of coal’s aromaticity to gain final foam rigidity. Typically, polyols depend on the isocyanate fraction and cross-linking to gain rigidity. By utilizing coal, we were able to maintain rigidity while reducing the overall hydroxyl value of the polyol. This is important as lower hydroxyl value leads to greater percent weight of the coal-based polyol because less isocyanate is required for foaming. This leads to greater foam cost savings. This report provides the details, process, and process cost models of the conversion of coal to polyols and further to PU foams. Battelle’s process begins with coal liquids. These liquids can be obtained by two processes: coal coking or pyrolysis to produce coal tar, and Battelle’s biobased coal-to-liquids (CTL) process to produce heavy syncrude after liquifying >85% coal. After liquification, Battelle utilizes ozonolysis to create functionalization on the polyaromatic coal structure. The functionalization is then converted to the final polyester polyol through transesterification, or to hydroxyamide polyol through amidification. Equivalent or better standard properties have been obtained for 2 lb/ft 3 density rigid, water and freon-alternative blown foams, including compressive strength, density, R-value, and dimensional stability. Target applications for these foams are insulation, packaging, and energy-absorbing foams. Some exploratory testing also showed promise for adhesives applications. A detailed economic analysis showed that Battelle’s polyol process is economical, at a 140 metric tons per day (MTD) polyol production scale. An attractive return on investment (ROI) at competitive pricing validates the process is ready for a pilot-plant demonstration. A scale-up plan is provided.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2022

A Novel Process for Carbon Dioxide Conversion to Fuel

In this project, TDA developed a new mixed metal oxide-based sorbent that converts CO2 (captured from coal fired power plants) to CO, which can then be combined with renewable H2 generated by water electrolysis or H2 from steam methane reforming to produce different liquid fuels. TDA’s absorbent-based CO2 conversion process uses a redox process, which splits the catalytic reforming of methane with CO2 reaction into two stages: CO2 reduction to CO and CH4 reforming into H2 and CO which eliminates the equilibrium limitations. The CO produced in the two-stage reactor system can then be further reacted with renewable H2 to produce methanol, naphtha, diesel, or gasoline. We worked with the Advanced Power & Energy Program (APEP) of University of California, Irvine (UCI) to design and develop the liquid fuel synthesis process that is built around this new material. We demonstrated the techno-economic viability of the new sorbent based redox process to convert CO2 into synthesis gas by demonstrating continuous carbon dioxide reduction in a prototype test system for over 585 hours while converting up to 10 kg CO2/day. With the successful completion of the R&D effort, the technology is now ready for a larger pilot-scale demonstration and the technology readiness has been raised from TRL 3 to TRL 5. In collaboration with UCI, we completed a high-fidelity process design and economic analysis. The required sale price (RSP) for gasoline (Case 1 NG-MTG) is $4.91/gal and naphtha and diesel (Case 2 NG-FT) are $4.23/gal and $6.07/gal, respectively, on a 2011 dollar basis. To put these costs in perspective, the California prices in current dollars (with its strict specifications) for regular grade gasoline from last year to current year have varied from a low of $3.10/gal in January 2021 to a high of $5.76/gal in March 2022, while prices for diesel from last year to current year have varied from a low of $3.40/gal in January 2021 to a high of $6.41/gal in May 2022 according to the U.S. Energy Information Agency data. It should be noted that the gasoline and diesel produced by these designs of Case 1 and Case 2 would be of very high quality and both nitrogen and sulfur free. These RSPs are based on a cost of imported electricity of $64/MWh based on the low-end current wind generated electricity cost (Genevieve 2011). This cost is by far the largest component of the variable costs used in computing the RSPs. A sensitivity analysis of these RSPs to the cost of imported electricity shows that the cost of the imported electricity has a significant effect on the RSPs. The life cycle analysis (LCA) shows that the total cradle-to-gate CO2 emissions for both liquid fuels (diesel and gasoline) were negative, indicating that overall more CO2 is consumed than released during production of the fuel from CO2 feed stack for both cases (-296 kgCO2 per MT gasoline for Case 1 and -705 kgCO2 per MT diesel for Case 2). On a cradle-to-grave comparison, the use of diesel produced using TDA’s process (2,457 kgCO2 per MT diesel) would release 37.6% less CO2 compared to petroleum based diesel (3,937 kgCO2 per MT diesel) while the use of gasoline produced using TDA’s process (2,792 kgCO2 per MT gasoline) would release 29.3% less CO2 compared to petroleum based gasoline (3,946 kgCO2 per MT gasoline). With the successful completion of the R&D effort, the technology is now ready for a bench-scale demonstration and the technology readiness has been raised from TRL 3 (Analytical and experimental critical function and/or characteristic proof of concept) to TRL 5 (Laboratory scale similar system validation in relevant environment).

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2024

Microstructure Optimization and Novel Processing Development of ODS Steels for Fusion Environments (Final ARPA-E Report)

This project aimed to develop scalable, cost-effective fabrication of high-performance, oxide- dispersion-strengthened (ODS) steel using advanced manufacturing methods (AMMs) for fusion blanket-breeding applications. Gas atomization reaction synthesis (GARS) enables the synthesis of precursor ODS steel powders without prolonged mechanical alloying. This process creates a chromium (Cr)-enriched surface oxide with yttrium/titanium (Y/Ti)-enriched intermetallics in powder interiors. GARS powders were consolidated to >99% of the theoretical density using a first-of-a-kind shear assisted processing and extrusion (ShAPE) and laser-based powder bed fusion (L-PBF) AM processes. These processes led to ODS steels containing a high-density of nano-oxide dispersoids that enhance high-temperature mechanical properties. Such scalable, cost-effective fabrication of ODS steels can enable efficient power conversion cycles (=40%) at operating temperatures beyond 900 K in future fusion power plants.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Refining a Novel Process Monitoring Method to Safeguard Continuously Cycling Designs Using Isotopic Ratios

In advanced reactor (AR) designs, a common feature is continuous chemical processing and circulation of the nuclear material. This work bridges a significant measurement gap in safeguarding reactors with circulating fuel or continuous refueling by leveraging and building on the isotope ratio method first developed by our team under an FY21 Advanced Reactors International Safeguards Engagement (ARISE) project (Uribe et al. 2021). In circulating fuel designs, the radioisotope inventory changes from traditional effects (e.g., radioactive decay, fission) but also includes material transport due to pressure and temperature gradients. Such designs may also require regular or continuous additions or removals during operation, which significantly increases the rate of inventory change compared to traditional pressurized water reactor (PWR)s. Thus, directly tracking the nuclear inventory is ineffective since the isotopes are continuously added and removed. The isotope ratio method instead focuses on detecting changes to the input and output flows of radioisotopes. Previous work showed that for well-chosen pairs of isotopes, the isotopic ratio provides a sensitive and lasting indicator of deviation from normal conditions (e.g., startup, shutdown, diversion). The isotope ratio method is a process monitoring method with potential for application in for forward-looking approaches to International Atomic Energy Agency (IAEA) safeguards. The original process monitoring method was developed for a specific case—the decay tank of a thorium-fueled molten salt breeder reactor. In this expanded work, we explored other types of reactors and processes with nonstationary (e.g., flowing) nuclear material, which are difficult to safeguard with traditional methods because of the transient nature of the systems. The goal of the present work is to generalize the isotope ratio method for use in processes with continuously flowing nuclear material. All continuous processes have an average time for isotopes to be replaced in the system. The isotope ratio method works by choosing radioisotopes with half-lives both above and below the processing time. The present work seeks to explore which isotopes are suitable for the method by simulating the nuclear inventory, radioisotope emissions, and detector responses for several classes of advanced reactors. While the method can in principle be applied to other processes (e.g., enrichment or reprocessing facilities), the present work limits scope to ARs with continuously flowing fuel. Section 2 details the mathematics supporting the isotope ratio method, and Section 3 introduces the representative ARs selected for this work. Section 4 discusses how each reactor was analyzed, and Section 5 showcases the results for each representative reactor. Finally, Section 6 provides concluding remarks and suggests pathways for further analysis.

98 NUCLEAR DISARMAMENT, SAFEGUARDS, AND PHYSICAL P↗
DOE OSTI2026

Data for 3-Hydroxypropionic Acid Recovery from Fermentation Broth through Novel Downstream Processing: Technoeconomic Analysis

This study develops and validates a simplified, fully solvent-free downstream processing (DSP) strategy for high-purity recovery of 3-hydroxypropionic acid (3-HP) from real fermentation broth containing 62.3 g/L of 3-HP. Optimized activated carbon treatment achieved 98% color removal, while Amberlite IRA-67 was operated at pH 4.5 and 30 °C to minimize product loss. This is the first integrated demonstration of a fully solvent-free DSP enabling recovery of bio-based 3-HP as both a solid sodium salt and a concentrated aqueous solution, supported by techno-economic analysis. At lab scale, the process achieved 77.3% recovery of sodium 3-HP with 83.2% (w/w) purity and produced a 30% (w/v) aqueous solution. Techno-economic analysis yielded minimum selling prices of $0.551/kg for the solution and $0.892/kg for the salt, both below target thresholds for cost-competitive bio-acrylic acid production. Overall, these results demonstrate an efficient, scalable, and economically viable industrial pathway for 3-HP recovery.

Bioproducts↗
DOE OSTI2025

A Novel Manufacturing Process of Lightweight Automotive Seats (Integration of Additive Manufacturing and Reinforced Polymer Composite)

Lightweight automotive seats offer multiple benefits to original equipment manufacturers in terms of cost savings from various aspects, including less material usage, more integrated processes, and compliance with Corporate Average Fuel Economy Standards. Original equipment manufacturers have been focusing on innovative ways to produce light weight automotive seats. The commercially available automotive seats are currently made of multiple metal components combined through welding and fasteners. The use of additive manufacturing and composite structures is particularly useful for light weighting the automotive components. Additive manufacturing (AM) offers multiple advantages over traditional manufacturing processes such as freedom of design thereby enabling complex structural geometries, mass customization and waste minimization, and control over the fiber alignment through deposition in a predetermined pattern. Combining metal inserts with polymer composites through a novel manufacturing process allows design of lightweight and high-performance materials for automotive components. However, fabricating these metal polymer composite structures through traditional manufacturing processes limits their mechanical properties due to limited design freedom, lack of control over fiber orientation in composite parts, and poor interfacial bonding between the constituent materials. It is essential to develop a novel manufacturing process to enable high throughput production of lightweight automotive seats using metal and polymer composites. As such it is important to design the automotive seat suitable for manufacturing via this process and perform mechanical characterization on various subcomponents of the seat to ensure that the design and performance requirements provided by the auto manufacturer are met. The aim of this project is to develop a novel manufacturing technique to produce lightweight automotive seat by combining AM with conventional manufacturing processes. The car seat back panel will be designed via topology optimization and numerical simulations to minimize the overall weight while ensuring it meets all the performance requirements. The optimization of the seat back structure will be based on computational stress analysis to maximize the stiffness and minimize the weight. Materials currently used by Ford Motor Company will be adopted for a few subcomponents while the in-house composite materials will be used for the rest of the seat back. The composite and metallic materials will be tested to determine their mechanical properties as these are necessary for simulations. A novel manufacturing process will be developed to integrate AM metal inserts with discontinuous reinforced composite through large scale additive manufacturing and compression overmolding processes. The developed manufacturing technique will be used to fabricated various subcomponents suitable for the seat back design and mechanically tested to determine their properties. The manufacturing of the lightweight seat back design through this process involves integrated AM metal inserts with the composite structure for recliner connection. The manufacturing of the entire seat back which is lightweight through the novel manufacturing process will be discussed. The performance of the designed seat back will be investigated through numerical simulations and shown to meet all the requirements provided by the auto manufacturer. The final goal of developing a novel manufacturing process for lightweight automotive seats is met through design optimization of seat back, manufacturing of subcomponents, mechanical characterization, and validation through numerical simulations. The routes to achieve the final goal of the project and the depth in which they were investigated changed throughout the project due to personnel changes and the COVID-19 pandemic. The project resulted in the development of a novel manufacturing process to integrate metal inserts with tailored polymer composite preforms through overmolding. Leveraging this proven manufacturing process, a lightweight seat back was designed through topology optimization and numerical simulations. The designed seat back uses AM metal inserts and compression overmolding of tailored polymer composite preforms obtained via large scale additive manufacturing. The metal polymer composite structures fabricated through this process exhibited enhancement in stiffness and improved ductility upon testing. Overall, the project provided an alternative design and manufacturing technique for automotive seat back that enables weight saving while meeting the safety and performance requirements.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2026

Technoeconomic Analysis of a Novel Microwave Process to Produce Ethylene from Methane

Ethylene is a critical feedstock in industrial processes, serving as a raw material in the petrochemical industry to produce plastics and commodity chemicals. Conventional ethylene production routes are energy-intensive and contribute substantially to the carbon footprint of chemical manufacturing. In this study, an industrial-scale novel microwave process was simulated using ASPEN Plus to assess its economic viability. Technoeconomic analysis confirmed the economic competitiveness of the novel microwave process, with a levelized cost of ethylene of USD 0.51/kg compared to USD 0.56/kg for the conventional base case. Key economic drivers of the process were identified, and sensitivity analyses were conducted to evaluate their impact on project economics. Furthermore, 87.7% of the total utility consumption in the novel microwave process is electricity, highlighting its potential to contribute to the electrification of the chemical industry. The findings of this study confirm the economic feasibility of both industrial-scale microwave reactors and modular plant configurations for the production of ethylene from methane, offering a promising alternative to conventional processes.

electromagnetic radiation↗
DOE OSTI2025

Supercritical water desalination and oxidation (SCWDO): Effectiveness on complex solutions, technoeconomic, and CO 2 impact for produced water treatment

The modern energy-economy is increasingly causing the production of highly saline brines, including from produced water. Supercritical water desalination can concentrate and extract minerals from these brines, but the effects of mixed salt interactions, organic degradation with additives, and the technology's economics are not well understood at supercritical condition. The present study evaluated and experimentally studied an integrated supercritical water desalination and oxidation (SCWDO) process for treating real-produced water samples from oil/natural gas field. The complex interactions between the various anions and cations in produced water were extensively evaluated. Most of the divalent and trivalent ions were extracted below 250 °C while the majority of the monovalent salt were removed between 380 to 410 °C. The treated real produced water was of drinking water quality, with <500 mg/l of total dissolved solid (TDS) and with 100% organics removal. Furthermore, the heat liberated during the organic oxidation could be utilized internally and for electricity generation for enhanced the energy efficiency and lower cost of produced water treatment. With system optimization, the proposed SCWDO process can essentially be made a net zero energy process. A novel process flow diagram for the commercial scale self-powered hybrid SCWDO technology was proposed as a cost-effective produced water treatment to mitigate the environmental crises. Techno-economic analysis showed that produced water treatment cost with SCWDO can be reduced to 2–3 $/m 3 and can be up to 60 % cheaper to traditional deep well reinjection. Additionally, the proposed SCWDO process could achieve net negative CO 2 emission.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2025

Beta-Amino Carboxylate (BAC) non-aqueous physical solvents for enhanced CO2 separations in pre-combustion carbon capture, industrial CO 2 capture, and biogas upgrading processes

Novel beta-amino carboxylate (BAC) solvents have been synthesized and tested to efficiently capture carbon dioxide (CO 2 ) from process gas streams with CO 2 partial pressure intermediate between pre-combustion and post-combustion capture. The BAC solvents have molecular structures characterized by alkyl-substituted amides or esters containing a secondary amine functional group on the second carbon from the carbonyl carbon (referred to as the beta “β” carbon). The ester or amide functional group combined with optimal steric crowding around the amine nitrogen by proximate alkyl groups are tailored to modify the strength of CO 2 binding in the solvent. The solvents possess high CO 2 solubilities and high gas selectivity including good CO 2 /H 2 O selectivity and can be utilized for CO 2 absorption over a range of partial pressures. Due to low volatility, many of the solvents can be operated at or above ambient temperature which eliminates solvent chilling and allows regeneration using low grade waste heat. These novel solvents offer an opportunity for efficient carbon capture for a range of applications including biogas upgrading, hydrogen production, and pre-combustion carbon capture.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗