Search NASA⌕ Search

SEARCH · Search NASA

Results for “PV TECHNOLOGY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Accurate Efficiency Measurements for Emerging PV: A Comparison of NREL's Steady-State Performance Calibration Protocol Between Conventional and Emerging PV Technologies

Emerging PV technologies (e.g. Perovskite, and Quantum Dot) are commonly known to possess challenges for accurate performance measurement under the existing IEC 60904 series of standards, which were developed for conventional Si solar cells. Potential performance artifacts depending on scan rates and directions and light bias exposure history are often seen in those emerging solar cells. To avoid these artifacts and provide an unbiased and reliable efficiency measurement, NREL's Cell and Module Performance (CMP) Group has developed a steady-state performance calibration protocol - the asymptotic P MAX method. In this paper, we applied this procedure to four PV cell technologies, Si, CIGS, perovskite, and Quantum Dot (QD), and compared their performance variations between the transient and the steady-state conditions. By comparison, we found that the performance parameters ( i.e. V OC , I SC , FF, ..eta..) measured between fast I-V scans (and the asymptotic method (steady-state) change significantly for perovskite and QD cells. These changes do not happen for Si and CIGS cells. Furthermore, the statistical performance analysis on nearly 100 emerging cells received globally (including OPV, Perovskite, and QD) shows that over 70 % of the fast I-V scans have a relative performance deviation larger than 1% compared to those determined using the asymptotic P MAX scan. Given the complex dynamic behavior observed in emerging PV devices, the CMP group at NREL thus only certifies their steady steady-state performance using the Asymptotic P MAX method. We highly recommend similar steady-state performance calibration protocol for all researchers in emerging PV because accuracy in reported efficiencies is critical to the long-term success of those promising new PV technologies.

41 EE - Solar Energy Technologies Office (EE-4S)↗

Progress of the PV Technology Incubator Project Towards an Enhanced U.S. Manufacturing Base

In this paper, we report on the major accomplishments of the U.S. Department of Energy's (DOE) Solar Energy Technologies Program (SETP) Photovoltaic (PV) Technology Incubator project. The Incubator project facilitates a company's transition from developing a solar cell or PV module prototype to pilot- and large-scale U.S. manufacturing. The project targets small businesses that have demonstrated proof-of-concept devices or processes in the laboratory. Their success supports U.S. Secretary of Energy Steven Chu's SunShot Initiative, which seeks to achieve PV technologies that are cost-competitive without subsidies at large scale with fossil-based energy sources by the end of this decade. The Incubator Project has enhanced U.S. PV manufacturing capacity and created more than 1200 clean energy jobs, resulting in an increase in American economic competitiveness. The investment raised to date by these PV Incubator companies as a result of DOE's $ 59 million investment total nearly $ 1.3 billion.

14 SOLAR ENERGY↗

Assessing the Performance and Impact of PV Technologies on Storage in Hybrid Renewable Systems

Traditional monofacial photovoltaic (mPV) systems are commonly adopted and well-documented because of their lower upfront costs in comparison to bifacial photovoltaic (bPV) systems. This study investigates how PV technologies impact energy storage in grid-scale hybrid renewable systems, focusing on optimizing and assessing the performance of mPV and bPV technologies integrated with pumped storage hydropower. Using Ludington City, Michigan as a case study and analyzing real-world data such as solar irradiance, ambient temperature, and utility-scale load profiles, the research highlights the operational and economic benefits of bPV systems. The results reveal that bPV systems can pump approximately 10.38% more water annually to the upper reservoir while achieving a lower levelized cost of energy ($0.0578/kWh for bPV vs. $0.0672/kWh for mPV). This study underscores the outstanding potential of bPV systems in enhancing energy storage and management strategies, contributing to a more sustainable and resilient renewable energy future.

13 HYDRO ENERGY↗

Field-Array Benchmark of Commercial Bifacial PV Technologies with Publicly Available Data

We present results for a 75-kW field array deployed with rows of 5 different commercially available bifacial technologies. Four PERC (multi and mono) and 1 Silicon Heterojunction manufacturers are represented. Reference strings of equivalent monofacial PV modules are also installed in the 10-row field. High accuracy string-level DC monitoring and module-level measurements have been recorded for six months. Analysis indicates performance within expectation, with a cumulative model mean error within +/- 2% for both bifacial and monofacial models and cumulative bifacial energy gain between 6-9%. A custom-module to measure shading loss from the torque-tube was installed. One month data shows up to 6% irradiance non-uniformity. A fixed-tilt test-site with 3 years of bifacial data is also presented, with a bifacial gain of 3%.

41 EE - Solar Energy Technologies Office (EE-4S)↗

Solution for Predictive Physical Modeling in CdTe and Other Thin-Film PV Technologies

The main goal of this work was to eliminate the ambiguity between the observed performance changes under stress and their physical root cause by enabling a depth of modeling that takes account of diffusion and drift at the atomistic level coupled to the electronic subsystem responsible for a PV device’s function. Development of advanced physical models describing capture/emission/ recombination phenomena relevant to multivalent dopants, amphoteric centers, and donor-acceptor pairs was also accomplished. These models, incorporating grain bulk, grain boundaries, and hetero-interface properties, were implemented in a self-contained simulation tool that drastically reduces interpretation ambiguity and, for the first time, allows for predictive design of thin-film PV devices.

14 SOLAR ENERGY↗

Evaluation of Bifacial Modules and PV Technologies with Combined-Accelerated Stress Testing

In view of the increasing interest and market share of bifacial cells and modules, suitable substrates such as glass and transparent backsheets along with ethylene vinyl acetate (EVA) and polyolefin elastomer (POE) encapsulants were examined in combined-accelerated stress testing (C-AST) to evaluate and compare degradation modes. Testing with both monofacial and bifacial cells, we found glass-glass modules with monofacial cells led to greater grid finger breakage than those with polymeric backsheets. This is attributed to previous x-ray topography work showing higher stress in cells in glass-glass modules than glass backsheet modules. Consistent with the objectives of C-AST, which stresses modules at levels corresponding to the limits seen in the natural environment, we observed the UV-fluorescence signatures of modules tested in C-AST (considering the degradation associated with developing chromophores, moisture penetration and photobleaching effects) to be like those in fielded modules, more so than other chamber stress testing implemented for comparison. Finally, among multiple cell degradation modes that we observed such as light-induced degradation (LID), we differentiated susceptibility to potential-induced degradation (PID) on the back of the bifacial Passivated Emitter Back Cells (PERC) in C-AST. Confirming with ex-situ tests, we found polarization-type PID most prevalent in glass/glass modules with EVA as would be anticipated considering the greater leakage current through such module encapsulation. Unlike PID tests performed in the dark, which can lead to false positive PID test results, field-representative illumination is experienced by the modules on the front and back side while -1200 V system voltage is applied in C-AST, supporting the conclusion that this module type would be susceptible to PID in the field.

bifacial modules↗

Follow-Up from the Photovoltaic Reliability Workshop (PVRW): Cost Modeling Capabilities to Evaluate Trends in PV Technologies

NREL's Solar and Storage Techno-Economic Analysis (TEA) team reviews live polling results from the Photovoltaic Reliability Workshop (PVRW) related to module technology trends believed to have the greatest reliability impacts. Then, the team reviews the publicly available tools and inputs necessary for evaluating reliability tradeoffs between initial module and system costs, degradation profiles, and levelized cost of energy (LCOE). These tools include the online Detailed Cost Analysis Models (DCAM) and the DuraMAT LCOE calculator.

cost modeling↗

PV Technology for Today and Tomorrow (Presentation)

The presentation was given as a webinar to the Solar Instructor Training Network on August 13, 2010. It summarizes the three primary types of photovoltaic technologies, why the three approaches are useful and some advantages and disadvantages of each approach. At the end is an answer to a question that was asked.

14 SOLAR ENERGY↗

End-of-Life Management of Photovoltaic Panels: Trends in PV Module Recycling Technologies

Photovoltaic (PV) technology is one of the most promising technologies for improving energy security and mitigating climate change. The PV market is growing rapidly, and further market expansion is expected all over the world. In addition to its positive impacts on energy security and climate change, PV technology is also among the most environmentally friendly technologies of all energy and electricity generation technologies, particularly when evaluated from a life-cycle viewpoint, including end-of-life management. This means that proper end-of-life management is an indispensable issue for 'clean' energy technologies. All technologies eventually degrade to where they enter their end-of-life stage, eventually requiring replacement. PV modules have a useful lifespan of approximately 30 years. With PV deployment increasing exponentially, the number of PV modules that reach the end of useful life will also greatly increase after the time lag of operation, accumulating proportionately as waste. A report published by International Energy Agency Photovoltaic Power Systems Programme (IEA PVPS) Task12 and the International Renewable Energy Agency (IRENA) in 2016 projected waste PV modules globally to amount to 1,7-8,0 million tons cumulatively by 2030 and to 60-78 million tons cumulatively by 2050. Generally, sustainable waste management offers opportunities known as the 3Rs: reduce, reuse, and recycle. When a product cannot be repaired or reused, recycling is the next preferable option before disposing as waste. In anticipation of the large volume of waste PV modules, and to retain PV's position as a clean energy technology, PV module recycling has become an important emerging topic, and various discussions and activities have been conducted and developed by governments, organizations, and companies. (Discussions on the topic of PV module reuse are considered to be less mature.) The EU Waste Electrical and Electronic Equipment (WEEE) Directive revised in 2012 (2012/19/EU) addresses the waste management of all electronics, including waste PV modules, in the EU member states. It requires 75%/65% (recovery/recycling rate) of waste PV modules by mass to be recycled through 2016, then increases to 80%/75% through 2018 and to 85%/80% thereafter. In addition to such a regulatory scheme, it is obvious that recycling technologies must be available to meet the increasing requirements of WEEE. Available recycling facilities that treat PV modules can meet current WEEE requirements; additional research and development (R&D) is required to meet subsequent WEEE requirements at reasonable cost. This report aims to provide an international survey of trends related to the development of PV module recycling technology from the perspective of both the private and public sectors. For the private sector, we review patents, as patent filing has been increasing since 2011. For the public sector, we review R&D plans and investments made by many countries active in PV module recycling technology development. Because it takes a long time to develop and commercialize new technologies, we hope that this report will accelerate technology development through transparent sharing of status and insight pertaining to the development of PV module recycling technologies. Managing end-of-life PV modules to recover valuable materials that can displace virgin ones is an important step toward meeting the challenge of sustainabiliy.

14 SOLAR ENERGY↗

Enhancement of Solar Energy Representation in the GCAM Model

The representation of solar technologies in a research version of the GCAM (formerly MiniCAM) integrated assessment model have been enhanced to add technologies, improve the underlying data, and improve the interaction with the rest of the model. We find that the largest potential impact from the inclusion of thermal Concentrating Solar Power plants, which supply a substantial portion of electric generation in sunny regions of the world. Drawing on NREL research, domestic Solar Hot Water technologies have also been added in the United States region where this technology competes with conventional electric and gas technologies. PV technologies are as implemented in the CCTP scenarios, drawing on NREL cost curves for the United States, extrapolated to other world regions using a spatial analysis of population and solar resources.

14 SOLAR ENERGY↗