Search NASA⌕ Search

SEARCH · Search NASA

Results for “Scanning transmission X-ray microscopy”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Soft X-ray reflection ptychography

Scanning transmission X-ray microscopy and ptychography have become mature tools for high-resolution, element-specific imaging of nanoscale structures. However, transmission geometries impose stringent constraints on sample thickness and preparation, thereby limiting investigations of extended or bulk specimens, especially in the soft X-ray region. Here, we demonstrate reflection-geometry soft X-ray ptychography as a robust imaging mode. Instrumental feasibility and spatial resolution are established using a lithographically defined Siemens star and barcode test pattern on a multilayer substrate. We empirically demonstrate a full-pitch spatial resolution of ca. 45 nm from Fourier ring correlation analysis of the reconstructed object. The results highlight the potential of the reflection geometry for nondestructive X-ray studies of materials without the need for transmissive samples.

Guenzing, Damian [Lawrence Berkeley National Labor↗
DOE OSTI2026

Using X-ray spectrum imaging to quantify fission gas in high-burnup UO2 fuel

Analysis of fission gas bubbles (FGBs) in light-water reactor (LWR) fuel is needed to improve the understanding and predictive capability of fuel evolution under normal- and transient conditions. One of the most important parameters of a FGB is the pressure of the gas, primarily Xe, inside it. Bubble volume and location (inter- vs. intragranular) are important considerations as well. However, experimental analysis of such bubbles is challenging due to their small size and embedded nature, and usefulness of the data requires large numbers be analyzed. This paper proposes a method to measure the pressure of Xe bubbles using X-ray spectrum imaging (XSI) in scanning transmission electron microscopy (STEM). From X-ray generation and instrumental parameters, the number of Xe atoms yielding a given number of Xe L-series X-ray counts is estimated, and then from the estimated volume of the bubble the Xe density is estimated, which can then be converted to pressure via an equation-of-state. We apply the method to XSI datasets from high burnup (HBu) fuel from North Anna 1 reactor in as-irradiated and post-LOCA-test conditions and find Xe pressures in the FGBs clustered around 1 GPa.

Parish, Chad [ORNL] (ORCID:0000000312097439)↗
DOE OSTI2025

Effect of Preparation Conditions of Fe@SiO2 Catalyst on Its Structure Using High-Pressure Activity Studies in a 3D-Printed SS Microreactor

Fischer–Tropsch synthesis (FTS) in a 3D-printed stainless steel (SS) microchannel microreactor was investigated using Fe@SiO2 catalysts. The catalysts were prepared by two different techniques: one pot (OP) and autoclave (AC). The mesoporous structure of the two catalysts, Fe@SiO2 (OP) and Fe@SiO2 (AC), ensured a large contact area between the reactants and the catalyst. They were characterized by N2 physisorption, H2 temperature-programmed reduction (H2-TPR), scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR), X-ray photoelectron microscopy (XPS), and thermogravimetric analysis–differential scanning calorimetry (TGA-DSC) techniques. The AC catalyst had a clear core–shell structure and showed a much greater surface area than that prepared by the OP method. The activities of the catalysts in terms of FTS were studied in the 200–350 °C temperature range at 20-bar pressure with a H2/CO molar ratio of 2:1. The Fe@SiO2 (AC) catalyst showed higher selectivity and higher CO conversion to olefins than Fe@SiO2 (OP). Stability studies of both catalysts were carried out for 30 h at 320 °C at 20 bar with a feed gas molar ratio of 2:1. The Fe@SiO2 (AC) catalyst showed higher stability and yielded consistent CO conversion compared to the Fe@SiO2 (OP) catalyst.

Biochemistry & Molecular Biology↗
DOE OSTI2026

Thermoreflectance Detection of Point Defects Resulting from Focused Ion Beam Milling

Focused ion beam (FIB) milling is a commonly used tool for nanoscale material processing, such as for transmission electron microscopy (TEM) sample preparation, or the creation of fiducial markers prior to other processes and measurements. During milling, a high energy ion beam is used to remove material via sputtering. The expelled target material may return to the sample surface however, affecting subsequent measurements. Beam spreading or irradiation due to neutral gallium may also irradiate a larger area than intended. Extensive research has explored the effects of FIB milling on the prepared TEM sample, but few have looked at the effects of milling on the properties of the sample surrounding the milled region. We use multiple pump-probe laser-based techniques (time domain thermoreflectance and steady-state thermoreflectance) to measure the spatial extent of FIB-induced surface/subsurface changes on a series of silicon wafers milled at multiple currents and doses. We supplement these measurements with high-resolution scanning transmission electron microscopy, energy dispersive X-ray spectroscopy, stylus profilometry, and time-of-flight secondary ion mass spectroscopy. We find a sample surface affected by the FIB up to 1 mm from where milling occurred, with a notable dependence on the ion beam current. We also note remarkably high sensitivity to surface defects using the thermoreflectance metrologies, including detection where other measurements failed.

defects↗
DOE OSTI2026

Modulating Mid-Gap Electronic States Through Site-Selective Modification in B-Pbx/B'-CuyV2O5/CdS Heterostructures for Photocatalytic Hydrogen Evolution

We interfaced ..beta..-Pbx/..beta..'-CuyV2O5 compounds, with varying stoichiometries of precisely positioned Pb-ions (x) and Cu-ions (y) in interstitial sites along a tunnel-structured ?-V2O5 framework, with cysteine-capped CdS (cysCdS) quantum dots (QDs) to yield heterostructured photocatalysts. ..beta..-Pbx/..beta..'-CuyV2O5 compounds exhibit midgap electronic states with orbital contributions from both Cu 3d and stereochemically active Pb 6s states that show distinctive light-initiated reactivity with photoexcited QDs. ..beta..-Pbx/..beta..'-CuyV2O5/CdS heterostructures were prepared by linker-assisted assembly (LAA). Scanning and transmission electron microscopy, energy-dispersive X-ray spectroscopy, and Raman spectroscopy revealed that cysCdS QDs were deposited onto surfaces of ..beta..-Pbx/..beta..'-CuyV2O5 via LAA. HAXPES revealed that the site-selective positioning of Pb-ions and Cu-ions promoted close energetic alignment of the midgap states of ..beta..-Pbx/..beta..'-CuyV2O5 compounds with the valence-band maximum of cysCdS QDs. Transient absorption spectroscopy revealed that photogenerated holes were transferred from CdS QDs to midgap states of ..beta..-Pbx/..beta..'-CuyV2O5 compounds on time scales <50 ps. Finally, photoelectrochemical and photochemical experiments revealed that ..beta..-Pbx/..beta..'-CuyV2O5/CdS heterostructures promoted the photocatalytic reduction of H+ to H2. In photoelectrochemical experiments, under oxidative conditions, for all ..beta..-Pbx/..beta..'-CuyV2O5/CdS heterostructures, H2 was evolved at a Pt counter electrode while a sacrificial donor was oxidized at the heterostructure-functionalized working electrode. In contrast, under reductive conditions, for ..beta..-Pb0.152V2O5/CdS and ..beta..-Pbx/..beta..'-CuyV2O5/CdS heterostructures, H2 was evolved at the working electrode. In photochemical experiments, dispersed ..beta..-Pbx/..beta..'-CuyV2O5/CdS heterostructures promoted the reduction of H+ to H2 under white-light illumination; ..beta..'-Cu0.55V2O5/CdS and ..beta..-Pbx/..beta..'-CuyV2O5/CdS heterostructures, for which midgap states have Cu 3d orbital character, generated 2-fold more H2 than ..beta..-Pb0.152V2O5/CdS heterostructures. Cu-ion insertion thus appends additional acceptor surface states that improve ligand-mediated hole transfer from photoexcited QDs, but such states are intrinsically limited in mediating hole transport to the substrate as a result of the low mobility of holes in narrow Cu 3d-states. Our results reveal that the density and orbital character of midgap states of ..beta..-Pbx/..beta..'-CuyV2O5 compounds, tunable through recently developed site-selective ion insertion strategies, determine efficiencies of charge-transfer and charge-transport mechanisms that underpin photocatalysis.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Directing Assembly of Mesoscale Multi‐Shell Morphologies of DNA Origami Crystals

Nature builds hierarchically ordered materials, such as seashells, wood, and bones, through spatially and temporally regulated growth. Mimicking such a level of control in synthetic systems remains challenging, particularly in achieving multiscale organizations with prescribed nanoscale arrangements and desired material morphologies. In this study, we introduce a DNA-based self-assembly strategy for constructing diverse multi-shell mesoscale morphologies from nanoscale lattices, enabling prescribed structural, and compositional 3D material patterns. Using DNA origami frames as modular monomers, we direct anisotropic epitaxial growth through addressable DNA frame binding motifs and encapsulate nanoparticles (NPs) in desired 3D patterns. Sequential monomer addition under thermodynamically favorable conditions enables shell growth through heterogeneous nucleation while minimizing unwanted homogeneous nucleation. Here, we demonstrate that DNA-encoded addressability enables epitaxial shell growth along specific lattice directions, yielding crystals with multilayered mesoscale organization, including tube-like (sushi roll) and plate-like (macaron) morphologies. Shell-specific NP configurations and compositions are achieved through addressable and differentiated placement of NPs within each shell, as validated by small-angle x-ray scattering and cross-sectional scanning transmission electron microscopy. We further demonstrate addressable NP release and reveal that shells modulate release kinetics. Together, these findings establish a platform for fabricating DNA origami crystals with programmable mesoscale morphologies, nanoscale structure, composition, and transport properties.

3D patterning↗
DOE OSTI2026

Small Molecule Inhibitor-Modulated Al 2 O 3 Atomic Layer Deposition on Monolayer MoS 2 for Controlled Nucleation

The integration of ultrathin dielectrics on two-dimensional (2D) semiconductors is essential for advancing beyond-Si electronics. However, the intrinsic inertness of van der Waals 2D basal planes remains a primary bottleneck to achieving uniform dielectric nucleation and growth. Here, in this study, we introduce a small molecule inhibitor (SMI)-modulated thermal atomic layer deposition (ALD) strategy, exemplified by aluminum oxide (Al 2 O 3 ) ALD on monolayer molybdenum disulfide (1L MoS 2 ) with acetic acid (HAc) SMI. The ABC-type sequence comprises HAc inhibitor (A), trimethylaluminum (TMA) precursor (B), and deionized H 2 O coreactant (C). In situ quartz crystal microbalance (QCM) studies reveal robust HAc adsorption on Al 2 O 3 and suppression of subsequent oxide growth on HAc-passivated surfaces. When applied to 1L MoS 2 , this inhibitory pathway enables HAc to selectively passivate nascent Al 2 O 3 nuclei formed on the MoS 2 surface, limiting their three-dimensional (3D) island coarsening and redirecting precursor adsorption toward the uncovered basal plane. Consequently, nearly continuous ultrathin (∼1.5 nm) Al 2 O 3 films are achieved on 1L MoS 2 with markedly improved uniformity compared to standard Al 2 O 3 ALD using TMA and H 2 O, as validated by atomic force microscopy (AFM), cross-sectional scanning transmission electron microscopy (STEM), and energy-dispersive X-ray spectroscopy (EDS). Density functional theory (DFT) calculations further provide atomistic insight into HAc-modulated Al 2 O 3 nucleation, corroborating the energetic preference of HAc for Al 2 O 3 over MoS 2 and attenuated TMA adsorption on HAc-passivated surfaces. Spatially resolved Raman spectroscopy also confirms that the HAc-modulated process preserves the structural integrity of 1L MoS 2 , with only minimal strain and doping perturbations observed after dielectric deposition. This SMI-modulated approach offers a broadly applicable framework for controlling ALD nucleation across various inhibitors, ALD chemistries, and 2D materials, opening opportunities for reliable dielectric integration in next-generation nanoelectronics.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Complex-Concentrated Anion Doping Enables Ultra-Stable Lattice Oxygen and Structural Integrity in Lithium-Rich Layered Oxide Cathodes

Lithium- and manganese-rich layered oxides (LMR) stand out as next-generation lithium-ion cathode chemistries, which harness both transition-metal and lattice-oxygen redox processes to deliver exceptional capacity and energy density. However, their full potential is hindered by intrinsic oxygen instability and structural degradation, resulting in pronounced voltage fade and capacity decay. Here, we present a complex-concentrated anion-doping paradigm in which multiple anions, F, Br, and S, are incorporated into the oxygen sublattice to enhance oxygen-redox and structural stability. X-ray absorption spectroscopy and aberration-corrected scanning transmission electron microscopy confirm ultra-stable local oxygen coordination environments during long-term cycling, with detrimental phase transformations and oxygen-loss-induced cavitation dramatically inhibited. Notably, we show that the characteristic LiTM6 transition metal (TM) honeycomb ordering is preserved even after electrochemical cycling. Concurrently, this strategy yields an unprecedented volume change of only 0.63% upon charging to 4.8 V vs. Li+/Li, achieving the first zero-strain LMR cathode. The resulting LMR cathode delivers ultralow voltage fade (1 mV per cycle during the first 100 cycles and becomes negligible in subsequent cycles) and outstanding energy retention (93% after 200 cycles) in a pouch cell configuration. Our complex-concentrated anion-doping concept establishes a broadly applicable strategy for resolving chemo-mechanical failure mechanisms in ceramic intercalation electrodes for next-generation energy storage.

Li-ion batteries↗
DOE OSTI2026

Quadratic magnetoresistance across the insulator–metal transition in V4O7 thin films

We present a comparative magnetotransport study of V4O7 thin films grown simultaneously on single-crystal Al2O3 (r-cut) and amorphous SiO2 substrates, to examine substrate-induced effects on electronic transport across the insulator–metal transition (IMT). Temperature-dependent resistivity reveals a broad electronic ordering regime below the IMT, with both films exhibiting similar transition temperatures but differing by nearly an order of magnitude in absolute resistivity. Despite this strong substrate dependence of the resistivity scale, the magnetoresistance remains predominantly quadratic in magnetic field over wide temperature intervals for both substrates. Analysis of the quadratic magnetoresistance defines an effective mobility scale that evolves systematically across the IMT and exhibits a similar temperature dependence for the two films. Structural characterization, including atomic-resolution scanning transmission electron microscopy of the V4O7/Al2O3 interface and azimuthal X-ray diffraction measurements, reveals a sharp interface and well-defined in-plane crystallographic registry for the r-cut film, in contrast to the rotationally averaged in-plane structure expected for films grown on amorphous SiO2. These results indicate that while substrate-controlled structural registry modifies the resistivity scale, the quadratic magnetotransport response across the IMT remains largely robust, providing a consistent diagnostic of electronic transport in V4O7 thin films.

25 ENERGY STORAGE↗
DOE OSTI2026

Ca Metal Batteries and Sn Anode Alloying: Resolving Misconceptions in Ca–Sn Alloy Formation

Ca metal anode suffers from surface passivation and struggles to effectively plate and strip in conventional Ca electrolytes, making the development of alloy anode for calcium metal battery essential. This work systematically and carefully evaluates the electrochemical formation and feasibility of the Sn anode and its possibility of alloying with Ca using a combination of cyclic voltammetry, scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM/EDS), X-ray diffraction (XRD), and synchrotron transmission X-ray microscopy (TXM). Electrochemical measurements and SEM/EDS analyses indicate apparent Ca alloy formation. However, detailed XRD and TXM characterization reveal substantial lithium-ion involvement when lithium metal is employed as the reference electrode, even in electrolytes with high Ca salt concentrations. These findings highlight a significant risk of misinterpretation: Although limited Ca–Sn alloying may occur, the faster kinetics of Li + can dominate the alloying process, leading to a Li-driven reactions at the Sn anode. In contrast, cells constructed with Ca metal as both reference and counter electrodes exhibit distinct redox features only during the initial cycles, followed by rapid cell failure. The high oxidation currents induce severe Ca passivation, occurring nearly concurrently with Sn dealloying. Overall, this study provides critical insight into the practical limitations and common experimental artifacts associated with Ca metal battery systems and underscores the necessity for rigorous cell design and cautious interpretation when evaluating alloy chemistry in multivalent Ca-based batteries.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Electron beam irradiation effects on bulk metals: a comparative study of polycrystalline versus single-crystalline structures

This study investigates the effects of electron beam (e-beam) irradiation on the mechanical and structural properties of eight bulk metallic samples, comprising both polycrystalline (PC) and single-crystalline (SC) forms of Ni, Cr, V, and Ti. These metals were evaluated as potential candidates for beam exit windows in high-power (MW-class) particle accelerators. The primary objective is to identify metals capable of withstanding the conditions of high-power/MW-class e-beam accelerators and serve effectively as exit windows. Selection criteria were based on each metal’s intrinsic properties, power dissipation capability, and irradiation-induced changes in mechanical behavior, including hardness, elastic modulus, and defect density. Comprehensive characterization was conducted using field-emission scanning electron microscopy (FESEM), atomic force microscopy (AFM), scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM–EDS), X-ray diffraction (XRD), high-resolution transmission electron microscopy (HRTEM), selected area electron diffraction (SAED), and nanoindentation, performed both before and after exposure to a ~¿66 kGy dose from a 10 MeV e-beam accelerator. Results revealed that e-beam irradiation induced hardening in PC Ni, whereas PC Ti, commonly used in beam exit windows, exhibited softening. The observed softening in PC Ti is attributed to grain coarsening, elongation, and the formation of twins and twin boundaries, in contrast to the smaller, compressed grains in the pristine (Pr) PC Ti samples, consistent with the Hall–Petch relationship. The stresses due to twinning are small and insignificant in influencing the overall hardening of the PC Ti irradiated sample when compared to the stresses due to the dislocation density. Conversely, SC Ti samples exhibited irradiation-induced hardening. The SC Ti irradiated samples developed additional irradiation-induced modifications in crystallographic texture of (100), (101), (110), (200), (112), (004), and (211) as evidenced from the XRD results, which could probably explain the hardening effect that is caused by irradiation.

36 MATERIALS SCIENCE↗
NASA NTRS2026

Thermochemical Stability of Ca2Yb8(SiO4)6O2 Apatite in Presence of Molten Calcium-Magnesium-Aluminosilicate (CMAS)

Thermochemical stability of ytterbium silicon oxyapatite Ca 2 Yb 8 (SiO 4 ) 6 O 2 (CYbS) in the presence of molten calcium-magnesium aluminosilicate (CMAS) has been investigated at elevated temperatures for consideration as a thermal and environmental barrier coating (T/EBC) material. CYbS apatite powder was synthesized from the constituent oxides via a solid-state reaction method. Hot-pressed apatite substrates were exposed to molten CMAS at 1200, 1300, and 1400 °C for 1, 10, and 50 h. Development of phases in the interaction region of the heat-treated specimens was monitored using scanning electron microscopy, transmission electron microscopy, high-angle annular dark-field imaging, selected area electron diffraction, and energy dispersive x-ray spectroscopy. Monoclinic cyclosilicate Ca 3 Yb 2 (Si 3 O 9 ) 2 formed from interaction of CYbS apatite with CaO in the CMAS melt at the apatite-CMAS reaction front and continued to nucleate and grow within the residual CMAS in diffusion couples annealed for 1 to 50 h at 1200 °C as well as in those heat treated at 1300 °C for 1 h. Residual CMAS was depleted of Ca when cyclosilicate was present. Dendritic wollastonite (CaSiO3) was observed within the residual CMAS in couples annealed at 1200 and 1300 °C. Ingress of molten CMAS, because of its exponential decrease in viscosity, occurred through open pores and along the grain boundaries of the apatite substrates without any detectable chemical reaction at 1300 and 1400 °C. Results of this study indicate that Ca 2 Yb 8 (SiO 4 ) 6 O 2 apatite has the potential to mitigate the CMAS corrosion up to about 1200 °C but not at higher temperatures.

Narottam P Bansal↗
DOE OSTI2026

Plasma-Enhanced Atomic Layer Deposition Synthesis of Nanolayered Molybdenum Diselenide (MoSe 2 ) Thin Films for Nanoelectronics

Nanolayered molybdenum diselenide (MoSe 2 ) thin films were synthesized by plasma-enhanced atomic layer deposition (PE-ALD) using molybdenum pentachloride (MoCl 5 ) and diethyldiselenide (C 4 H 10 Se 2 ) precursors. Scanning and transmission electron microscopy revealed horizontally stacked nanolayers near the substrate and vertically oriented nanosheets at the surface of the film. X-ray diffraction confirmed the (002), (100), and (110) reflections of crystalline MoSe 2 , while X-ray photoelectron spectroscopy showed relative atomic concentrations of 33.5% Mo and 66.5% Se, consistent with stoichiometric MoSe 2 . Raman spectra exhibited characteristic E 1g , A 1g , and E$^1_{2g}$ vibrational modes. Field-effect transistors incorporating PE-ALD-grown MoSe 2 as the channel material displayed p-type behavior, demonstrating the potential of nanolayered MoSe 2 for nanoelectronic applications. This work demonstrates the feasibility of low-temperature, stoichiometric growth of nanolayered MoSe 2 by PE-ALD and its direct integration into transistor architectures.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Crystallographic registry in epitaxial V3O5 thin films

Crystallographic orientation plays a central role in determining transport properties in correlated oxides with low-hysteresis metal–insulator transitions. Here, V3O5 thin films were grown on Al2O3 (0001) and their crystallographic registry was evaluated using x-ray diffraction and cross-sectional transmission electron microscopy. θ–2θ measurements show a single out-of-plane orientation defined by the (202) reflection. Azimuthal φ-scans of the V3O5 (310) reflection exhibit twelve discrete maxima over 360°, indicating a finite set of in-plane orientations imposed by the substrate symmetry. High-resolution TEM and fast Fourier transform analysis confirm crystallographic coherence at the film–substrate interface. The electrical conductivity exhibits a metal–insulator transition at TMIT ≈ 423 K with no measurable thermal hysteresis and a total change of ~1.6 orders of magnitude between 300 and 480 K. These results establish crystallographic registry in epitaxial V3O5 thin films and provide a structurally well-defined system for future studies of orientation-dependent transport.\r\nT

36 MATERIALS SCIENCE↗
DOE OSTI2026

Formation of Bimetallic Nanoparticles via Exsolution Using a Reducible Metal Oxide Capping Layer

Bimetallic nanoparticles are promising catalysts that can improve performance in heterogeneous catalysis and solid-state electrochemistry. Exsolution is a useful method for forming such nanoparticles; however, it is limited by the elements present within the host oxide lattice. Here, in this work, we develop and demonstrate a strategy to form bimetallic particles from La 0.5 Sr 0.5 Ti 0.94 Ni 0.06 O 3 (LSTN) exsolution and using a reducible SnO 2 capping layer, expanding the range of elements available for bimetallic nanoparticle formation. Using this capping layer strategy, we formed nickel–tin (Ni 0 –Sn 0 ) bimetallic nanoparticles via exsolution. We used in situ near-ambient pressure X-ray photoelectron spectroscopy to monitor surface chemical changes during exsolution, showing that first, SnO 2 volatilized. This SnO 2 loss exposed the perovskite surface of LSTN to reducing conditions, which induced Ni exsolution, and compounded with SnO 2 reduction led to the formation of bimetallic Ni 0 –Sn 0 particles. To evaluate the associated microstructural evolution, we measured grazing incidence small-angle X-ray scattering (GISAXS), which confirmed the loss of the SnO 2 capping layer, and scattering simulations suggested the formation of bimetallic particles. We confirmed the bimetallic nanoparticle composition and morphology by Auger spectroscopy and scanning transmission electron microscopy. The resulting bimetallic nanoparticles were smaller and more thermally stable than the monometallic Ni counterparts on LSTN. This capping layer and exsolution approach allow synthesizing multimetallic nanoparticles and can be applied to other reducible metal oxides and perovskite hosts, broadening the compositional space for advanced catalytic materials.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Multiscale Cryo Electron Microscopy Reveals Interfacial Degradation and Stabilization in Battery Electrodes

Electrochemical interfaces are dynamic systems, evolving based on their local environment and reactant surface structures. The electrode-electrolyte interface in Li-ion batteries can be protective, limiting parasitic reactions with the electrolyte to passivate the surface [1]. Additionally, this interphase has an impact on the Li-ion transport through that layer based on its composition, bonding environment, and thickness. These parameters are challenging to collect and may vary depending on the electrode surface site investigated relative to its spatial position in a coin cell. This study will detail a multiscale cryogenic electron microscopy approach where millimeter-scale cross-sections through the coin cell batteries were made using a cryogenic stage within a fs-laser plasma focused ion beam (laser PFIB) with complementary energy dispersive X-ray spectroscopy able to detect variations in the composition at electrode interfaces [2]. Microscale cross-sectioning and lamella sample preparation of battery electrodes was conducted at the Center for Integrated Nanotechnologies using a Ga-ion focused ion beam (FIB) with air-free and cryo-transfer [3], followed by nanoscale mapping of composition and bonding within the CEI through cryo-scanning transmission electron microscopy (cryo-STEM) electron energy loss spectroscopy [4]. This multiscale approach enabled identification of millimeter-scale features of a battery stack with visualization of degradation in electrodes such as cracks in cathode particles, gas evolution, and SEI evolution; microscale interfacial characteristics, such as heterogeneity in the SEI or barrier layer and identification of electrolyte networks to the electrode surfaces; and nanoscale measurement of the CEI thickness, mapping of transition metal bonding within the cathode particles to identify loss of active materials, and identification of beneficial electrolyte additives incorporated into the CEI structure. This multiscale approach allows for a statistical understanding of the primary mechanisms and parasitic degradation pathways that impact performance by limiting the ion transport pathways within Li+ batteries.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Mechanical Behavior of Neutron Irradiated Refractory Multi-Principal Element Alloys Processed via Spark Plasma Sintering

The search for advanced materials capable of withstanding the extreme conditions of Generation IV reactors is a critical area in materials science research. These reactors operate under severe environments, including high temperatures, corrosion, stress, and irradiation damage. Consequently, there is a need for innovative alloy systems to ensure the reliability and longevity of proposed Generation IV reactor components. Refractory multi-principal-element alloys (RMPEA) have emerged as a promising candidate due to their exceptional properties. These alloys, characterized by their composition of multiple principal elements in near-equiatomic ratios, exhibit superior resistance to irradiation damage, reduced void swelling, enhanced microstructural stability, and minimal irradiation-induced hardening. While initial studies on RMPEAs have shown promising results, most research has been limited to thin films, nanocrystalline microstructures, and ion irradiation, which do not accurately represent the behavior of bulk materials. To address this gap, our research focused on the neutron irradiation of bulk RMPEAs. We aim to conduct comprehensive post-irradiation examinations (PIE) of RMPEAs irradiated at the Advanced Test Reactor at Idaho National Laboratory. The RMPEAs were synthesized using spark plasma sintering (SPS) with mechanically alloyed metallurgical powder. The RMPEA specimens are a MoNbTi alloy system with additions of -Zr, and -ZrV. Furthermore, PIE consisted of mechanical testing and advanced materials characterization. The mechanical testing consisted of sub-sized tensile testing, micro- and nano- indentation. Microstructural characterization included scanning electron microscopy and transmission electron microscopy. Mechanical testing coupled with advanced microscopy techniques provides insight into phase morphology and its effects on the mechanical properties of the RMPEA specimens. The results indicate that both pristine and irradiated RMPEA specimens exhibited brittle behavior during tensile testing, which can be attributed to their heterogeneous microstructure. The SPS manufacturing process did not include any post treatment, which resulted in a heterogeneous microstructure. Energy-dispersive X-ray spectroscopy revealed the presence of intermetallic such as laves phases within the microstructure. Specifically, Ti-rich precipitates were observed in the MoNbTi specimen, while Mo-rich precipitates were found in the MoNbTiZrV specimen. Nano-hardness testing of pristine samples showed that the laves phases exhibited higher hardness values compared to the matrix phase, suggesting that precipitate hardening is likely the dominant hardening mechanism in these specimens. The results from this work will be used to build a finite element model to predict mechanical behavior of future MPEA compositions. Thus, enabling for a streamlined approach to developing novel MPEAs for the nuclear industry.

36 - MATERIALS SCIENCE↗
DOE OSTI2026

Coupling Microstructural Evolution Simulations to Material Property Degradation Predictions for Plasma-Facing Materials

Reliable material performance is required for plasma-facing material (PFM) candidates. Previous research has shown that plasma and neutron radiation exposure induces microstructural changes in PFMs; changes in thermal and electrical conductivities and in material hardening and embrittlement were also observed after neutron irradiation. These material property changes will negatively impact the performance of the PFMs in a fusion reactor. Despite the well-known connection between material microstructure, properties, and performance, there is a need for validated modeling capabilities connecting PFM property degradation with microstructural evolution under fusion-relevant conditions. We are developing a simulation capability to couple plasma-induced microstructural evolution to material property degradation. Our approach relies on deliberate mapping between individual simulation models and experimental characterization for validation. The open-source Multiphysics Object-Oriented Simulation Environment (MOOSE) software was used for this simulation capability development. A MOOSE phase-field model was coupled with the cluster dynamics code, Xolotl, to predict microstructural evolution. Microstructure characterization techniques, including scanning electron microscopy (SEM), transmission electron microscopy (TEM), and laser scanning confocal microscopy (LSCM) are used to validate these microstructural evolution simulations. Calculation of thermal and electrical conductivities with first principles simulations was performed for bulk material and for grain boundaries; these results are used within MOOSE models to calculate effective thermal and electrical conductivities as a function of grain characteristics. Thermoreflectance and four-probe techniques were employed to measure the thermal and electrical conductivities, respectively. A MOOSE crystal plasticity model was adapted to predict microstructure-sensitive deformation behavior, and X-ray diffraction (XRD) was used to collect bulk dislocation density data for validation. After individual simulation validation, these models are coupled to predict material property changes resulting from plasma exposure. We focused here on an experimental design to emphasize the separate effects of moderate thermal loads and plasma exposure using tungsten. Annealing of tungsten was performed under a protective environment for temperatures ranging from 500 C to 1500 C. The plasma exposure was completed in the Tritium Plasma Experiment at Idaho National Laboratory under a deuterium flux of 1e22 D/m^2-s. This incremental approach is employed to build confidence in the modeling capability: separate-effects tests ensure that the models capture key mechanisms from single environmental conditions before predicting PFM property degradation under combined loads. We will show our early results from coupling these simulation models to predict PFM property changes from microstructural evolution. Comparisons of the simulation results with preliminary validation data will be discussed.

36 - MATERIALS SCIENCE↗