Search NASA⌕ Search

SEARCH · Search NASA

Results for “surface contamination”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

A Monte Carlo study of reflection electron energy loss spectroscopy spectrum of a carbon contaminated surface

It has been experimentally found that the carbon surface contamination influences strongly the spectrum signals in reflection electron energy loss spectroscopy (REELS) especially at low primary electron energy. However, there is still little theoretical work dealing with the carbon contamination effect in REELS. Such a work is required to predict REELS spectrum for layered structural sample, providing an understanding of the experimental phenomena observed. In this study, we present a numerical calculation result on the spatially varying differential inelastic mean free path for a sample made of a carbon contamination layer of varied thickness on a SrTiO{sub 3} substrate. A Monte Carlo simulation model for electron interaction with a layered structural sample is built by combining this inelastic scattering cross-section with the Mott's cross-section for electron elastic scattering. The simulation results have clearly shown that the contribution of the electron energy loss from carbon surface contamination increases with decreasing primary energy due to increased individual scattering processes along trajectory parts carbon contamination layer. Comparison of the simulated spectra for different thicknesses of the carbon contamination layer and for different primary electron energies with experimental spectra clearly identifies that the carbon contamination in the measured sample was in the form of discontinuous islands other than the uniform film.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Decontamination of urban surfaces contaminated with radioactive materials and consequent onsite recycling of the waste water

Enhancing rapid remediation strategies is paramount for recovery after a large-scale nuclear contamination event in an urban environment. Some current strategies recommend use of readily available equipment, materials, and facilities to expedite recovery. For example, applying pressurized water to contaminated surfaces may effectively remove radioactive contamination. In this study, a commercial power washer removes soluble forms of 152 Eu 3 + , 85 Sr 2 + , and 137 Cs + contamination from common porous building materials, and computer simulations characterize the recycling of the resultant contaminated wash water. Pressure washing the porous building materials under spray conditions typical with do-it-yourself units improved decontamination factors (DFs) for 152 Eu compared to low-pressure application of tap water (majority of two-tailed t-test p-values < 0.1), but pressure did not improve DFs for 137 Cs or 85 Sr. For both pressurized and low-pressure applications, adding potassium ions (K + ) to promote ion exchange reactions produced significantly higher DFs for tested radionuclides on asphalt, brick, and concrete. The resultant contaminated wash water can be processed through self-prepared chemical filtration beds of clay and sand. Modeled in a prior study, the beds yielded linear trends (R 2 > 0.98) in sensitivity analyses between most bed configuration variables and bed performance variables, permitting flexible ad-hoc bed design. The experimental and simulation results led to estimates of the remediation rate and waste generated after cleaning 250 m 2 of cesium-contaminated concrete from the combined deployment of a power washer and two different mobile treatment beds. Furthermore, the first treatment bed was designed to reduce treatment time and processed 1900 L of wash solution in 70 min using 880 kg of clay/sand infill material. Designed to reduce the solid waste generated, the second bed processed the same solution volume in 1040 min (17 h) using 170 kg of clay/sand infill material. The results of this analysis warrant further investigation of power washing with recycled salt solution as an effective rapid decontamination method with manageable waste.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Remotely sensed physical property estimation from powder contaminated surfaces

It is the intent of this paper to demonstrate the veracity of a method to estimate the total solid contaminant mass present on a sparsely coated surface encompassing a pixel from longwave infrared spectra. Sparsely coated surfaces create complex radiometry due to the interactions of electromagnetic energy between intimate materials. Current algorithms can be used on intimate mixtures to identify the abundances of materials in a pixel, but they cannot provide additional property information. Radiative transfer models can create mixture signatures, but only with a set of well-characterized physical parameters that are typically not known or are difficult to retrieve. Finally, the approach described here creates a parameter inversion model from a radiative transfer model and uses empirically measured mixture data to retrieve physical characteristics of the contaminated surface and derive a total contaminant mass present.

97 MATHEMATICS AND COMPUTING↗

Calculating Obscuration Ratios Of Contaminated Surfaces

Equations derived to estimate obscuration ratios of surfaces contaminated by particles. Ratio is fraction of surface area covered by particles. Useful as index of cleanliness in clean-room operations in manufacturing of semiconductor devices, magnetic recording media, optical devices, and pharmaceutical and biotechnological products.

Barengoltz, Jack B.↗

Optical measurements on contaminated surfaces

A bidirectional reflectometer system was developed for in situ measurements of the changes in spectral reflectance of surfaces contaminated with films of organic materials. The system permits experiments with films of controlled thickness in an environment that simulates the thermal, radiation, and vacuum conditions of space. The mechanical and optical construction of the reflectometer are discussed in detail, and actual data curves are used to illustrate its operation and performance.

Bonham, T. E.↗

Fluorescence Imaging Reveals Surface Contamination

In technique to detect surface contamination, object inspected illuminated by ultraviolet light to make contaminants fluoresce; low-light-level video camera views fluorescence. Image-processing techniques quantify distribution of contaminants. If fluorescence of material expected to contaminate surface is not intense, tagged with low concentration of dye.

Schirato, Richard↗

Influence of surface contamination on the wettability of heat transfer surfaces

In this study, the wettability of heat transfer surfaces plays an important role in liquid–vapor phase change phenomena, including boiling incipience, the critical heat flux, the Leidenfrost transition, and condensation. The influence of adsorbed surface contamination at the nanoscale, though seldom considered, can have a profound impact on wetting behavior. This study quantitatively investigates the impact of contaminant layer thickness on wettability. Various cleaning treatments are explored on zirconium and 6061 aluminum to determine the effect on contaminant and oxide layer thickness. Angle-resolved X-ray photoelectron spectroscopy can be used to measure the thickness of oxide and contaminant layers, which is then correlated to wettability by measuring the equilibrium contact angle. Results indicate that even after solvent cleaning, the contact angle of water on practical heat transfer surfaces is dominated by a hydrocarbon contaminant overlayer around five nanometers thick.

36 MATERIALS SCIENCE↗

Apparatus for Sampling Surface Contamination

An apparatus denoted a swab device has been developed as a convenient means of acquiring samples of contaminants from surfaces and suspending the samples in liquids. (Thereafter, the liquids can be dispensed, in controlled volumes, into scientific instruments for analysis of the contaminants.) The swab device is designed so as not to introduce additional contamination and to facilitate, simplify, and systematize the dispensing of controlled volumes of liquid into analytical instruments. The swab device is a single apparatus into which are combined all the equipment and materials needed for sampling surface contamination. The swab device contains disposable components stacked together on a nondisposable dispensing head. One of the disposable components is a supply cartridge holding a sufficient volume of liquid for one complete set of samples. (The liquid could be clean water or another suitable solvent, depending on the application.) This supply of liquid is sealed by Luer valves. At the beginning of a sampling process, the user tears open a sealed bag containing the supply cartridge. A tip on the nondisposable dispensing head is engaged with a Luer valve on one end of the supply cartridge and rotated, locking the supply cartridge on the dispensing head and opening the valve. The swab tip includes a fabric swab that is wiped across the surface of interest to acquire a sample. A sealed bag containing a disposable dispensing tip is then opened, and the swab tip is pushed into the dispensing tip until seated. The dispensing head contains a piston that passes through a spring-loaded lip seal. The air volume displaced by this piston forces the liquid out of the supply cartridge, over the swab, and into the dispensing tip. The piston is manually cycled to enforce oscillation of the air volume and thereby to cause water to flow to wash contaminants from the swab and cause the resulting liquid suspension of contaminants to flow into the dispensing tip. After several cycles to ensure adequate mixing, liquid containing the suspended contaminant sample is dispensed. The disposable components are then removed from the dispensing head, which may then be reused with a fresh set of disposable components.

Wells, Mark↗

Propulsive trajectory optimization to minimize surface contamination

MOTIVATION: We present an optimization technique for propulsive vehicles that autonomously minimizes contamination during surface approach and landing. In addition to short-range hoppers, the optimization technique is also fully applicable to traditional orbit-to-surface landers. This study addresses scenarios where surface alterations from propulsion events are counterproductive or hazardous to the mission objectives. This is of immediate interest for landers (whether human or robotic), that may rely on pristine soils collected in the immediate vicinity of landing sites to accomplish science investigations, mining, or ISRU surface operations. Such missions are averse to various surface-plume interactions such as thermal scoring, physical agitation, and contamination. The capability can be applied with minimal impact to the baseline mission concept. METHODS: Optimization algorithms have been developed to calculate descent trajectories and maneuvers, thrust magnitude, and attitude for various mission cases. These parameters are determined as an optimal solution when minimizing either fuel consumption, contamination deposited at the landing site, or some weighted combination of both. Among constraints imposed on the solution, we examined pitch rate, vertical takeoff and vertical landing (VTVL) requirements, size of the contamination zone, and minimum ground clearance during flight. This tool provides unique, non-intuitive solutions and can be a valuable resource for mission planners. RESULTS: A variety of agile trajectory solutions were obtained, each yielding different reductions in landing site contamination and corresponding to only modest increases in fuel consumption. Several optimal trajectories were obtained by varying the contamination weight in the fitness function. As expected, when the contamination weight is zero, the trajectory appears close to parabolic since the optimization scheme only attempts to minimize for fuel utilization, yielding essentially, the expected ballistic trajectory. Notably for contamination weights greater than zero, trajectory inflections are observed in the descent phase, which manifests as hovering or additional, mini “pseudo hops” before the final touchdown. A trajectory inflection is characterized by arresting the majority of the spacecraft vertical velocity component at a coordinate outside of the landing target, and without violating ground clearance constraints. FUTURE WORK: Our optimization technique is ready for laboratory or field demonstrations to validate the sophisticated maneuvering solutions obtained for fuel optimization and surface preservation. An appropriate testbed would validate the optimal guidance algorithms, the navigation system, and sensor suite by emulating vehicle flight in closed loop robotic tests. Critically, these algorithms could then be ported to flight software for implementation.

surface contamination↗

Composition suitable for decontaminating a porous surface contaminated with cesium

A method of decontaminating porous surfaces contaminated with water soluble radionuclides by contacting the contaminated porous surfaces with an ionic solution capable of solubilizing radionuclides present in the porous surfaces followed by contacting the solubilized radionuclides with a gel containing a radionuclide chelator to bind the radionuclides to the gel, and physically removing the gel from the porous surfaces. A dry mix is also disclosed of a cross-linked ionic polymer salt, a linear ionic polymer salt, a radionuclide chelator, and a gel formation controller present in the range of from 0% to about 40% by weight of the dry mix, wherein the ionic polymer salts are granular and the non cross-linked ionic polymer salt is present as a minor constituent.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Mitigation of Polystyrene Microsphere Surface Contamination for Wind Tunnel Applications

Polystyrene latex (PSL) microspheres have been utilized as seed material for flow visualization in wind tunnels. However, PSL microspheres have been observed to strongly adhere to wind tunnel and model surfaces. Surface contamination on the cleaning screens that remove vorticity and provide laminar flow in the test section, is particularly problematic. Agglomeration of particles on these screens cause constriction of the airflow through the screen resulting in inconsistent airflow properties in the test section. The adhesion mechanism of PSL microspheres to wind tunnel screens and 316 stainless steel flat plates, were evaluated in a contamination apparatus where small sections of screen material were exposed to PSL-seeded airflow. Using a design of experiments (DOE) methodology airflow seeding parameters were changed to evaluate how these modifications affected the degree of surface contamination. The solution composition, comprised of ethanol and water, was determined to be the most significant factor in particle adhesion. Utilizing image analysis software, data were collected from the contaminated surfaces and incorporated to generate predictive particle contamination models. A relationship was identified between the solvent evaporation rate, and the morphology and magnitude of PSL contaminants on the test surfaces. This analysis can be extended to other solvent mixtures to provide insight into simultaneously improving wind tunnel testing capabilities while diminishing facility contamination.

Wohl, Christopher J.↗

An OSEE Based Portable Surface Contamination Monitor

Many industrial and aerospace processes involving the joining of materials, require sufficient surface cleanliness to insure proper bonding. Processes as diverse as painting, welding, or the soldering of electronic circuits will be compromised if prior inspection and removal of surface contaminants is inadequate. As process requirements become more stringent and the number of different materials and identified contaminants increases, various instruments and techniques have been developed for improved inspection. One such technique based on the principle of Optically Stimulated Electron Emission (OSEE) has been explored for a number of years as a tool for surface contamination monitoring. Some of the benefits of OSEE are: it's non-contacting; requires little operator training; and has very high contamination sensitivity. This paper describes the development of a portable OSEE based surface contamination monitor. The instrument is suitable for both hand-held and robotic inspections with either manual or automated control of instrument operation. In addition, instrument output data is visually displayed to the operator and may be output to an external computer for archiving or analysis.

Perey, Daniel F.↗

Estimating Radionuclide Activity in Surface Contamination for GTCC Activated Metal Waste Streams - 18236

The U.S. Nuclear Regulatory Commission's licensing requirements for land disposal of low-level radioactive waste (LLRW) in 10 CFR Part 61 classify LLRW wastes as Class A, B, C, or Greater-Than- Class C (GTCC). GTCC waste includes activated metals that are generated primarily by nuclear power reactors. Activated metals represent a significant volume (880 cubic meters) of GTCC wastes that may be generated as current commercial power reactors are decommissioned. Additionally, these wastes are expected to contain radionuclides that are very long-lived and are mobile in the environment (e.g., Tc-99 and I-129) as well as transuranic radionuclides that, while not as mobile as other radionuclides, have greater potential for health consequences should such radionuclides reach receptor locations in sufficient concentrations. Quantities of surface contamination on activated metals have typically been reported using a combination of assumptions, calculations, and measurements. For example, projections of future activity associated with surface contamination, or the surface activity, for the activated metals is dependent on assumptions made regarding fuel behavior (e.g., modern fuel performance is expected to be different from fuel performance in the 1970's). In this study, we examined published information to better understand how assumptions, calculations, and measurements used for estimating quantities of surface contamination on activated metals can influence the estimated quantities. The analysis in this report was performed to better understand how estimates for the activated metal inventory of GTCC metal could influence potential decisions regarding the siting and design of disposal facilities. It was found that the variability in surface contamination either measured or estimated was sufficiently large that characterization of the radionuclide inventory for GTCC activated metals, especially the transuranic radionuclides, is critically important for establishing the siting and design requirements for a disposal facility. Overly conservative assumptions for the inventory could significantly limit disposal options, whereas, overly optimistic assumptions with respect to the inventory could lead to a disposal facility that may not protect off-site receptors. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Bulk lifetime indicates surface contamination

Indirect measurement of wafer surface impurities has sensitivity of 300 monolayers. Photoconductivity-decay apparatus determines bulk recombination lifetime in semiconductor materials. Bulk impurity levels before and after annealing relate to level of surface contamination. Method evaluates wafer cleaning techniques, qualifying purity of chemical and deionized water used, or monitors production process.

Blais, P. D.↗