Development of 22.5 % p-type tunnel oxide passivated contact solar cells through efficiency enhancement by replacing local Al-BSF in PERC cells with (p+) poly-Si/SiO2 carrier selective contact
Not Available
Choi, Wook-Jin (ORCID:000000032568419X)↗
Engineering topics
Upadhyaya, Vijaykumar D.
Publications and source records attributed to Upadhyaya, Vijaykumar D..
Evaluating the Performance and Reliability of Screen-Printable Fire-Through Copper Paste on PERC Solar Cells
A bifacial silicon heterojunction solar cell demands approximately 210 mg usage of silver paste (9 busbars, 24.5%, bifacial, M6 size wafer). Copper is an excellent alternative to silver: 100x cheaper, similar elecvtrical resistivities, and 1000x more abundant. Successful demonstration of large area selective emitter PERC solar cells using Cu fire-through paste with FF approximately 75% and approximately 19%. Paste chemistry results in oxide-based Cu diffusion barrier, leading to good reliability of the devices: 1000h DHT giving a 3.5% efficiency drop. The additional series resistance still needs to be lowered. Printed and fired cell performance is governed mostly by pFF, especially J02 ; same for DHT degradation. Further improvement in printing and firing optimization for lower series resistance and higher FF.
Ag↗
Exploring the Performance and Reliability of Screen-Printable Fire-Through Copper Paste on PERC Solar Cells
For 40 TW of PV required to transition our planet to 100% renewables, the silver (Ag) should disappear from PV production. Advantages of copper (Cu) over silver (Ag) include 1) bulk Cu has a similar conductivity to Ag (1.7 mu O-cm for Cu, 1.6 mu O-cm for Ag) and 2) Cu is approximately 100 times cheaper than Ag, making it an excellent potential replacement. Problems associated with copper (Cu) contacts include 1) easy oxidation and 2) diffusion into the Si cell and recombination activity.
copper paste↗
Development of APCVD BSG and POCl 3 Codiffusion Process for Double-Side TOPCon Solar Cell Precursor Fabrication
This paper presents a commercially viable process for fabricating a high-quality double-side tunnel oxide passivating contact (DS-TOPCon) cell precursor using APCVD-deposited boron silicate glass and ex-situ POCl 3 diffusion in a single high-temperature step, eliminating the need for additional masking and diffusion processes. A two-tier temperature profile was developed, involving a pre-annealing at above 900°C in nitrogen (N2) ambient followed by POCl 3 diffusion at 840°C. We investigated the effect of varying pre-annealing temperatures, ranging from 875°C to 950°C, on the passivation quality and metal-Si contact properties of both n-TOPCon and p-TOPCon layers. The resultant DS-TOPCon cell precursor after silicon nitride (SiNX) passivation exhibited an excellent iV OC of close to 730 mV. In addition, a rapid asymmetric poly-Si thinning technique, developed in this work, enabled adjustment of the front n + poly-Si thickness while maintaining the rear p + poly-Si thickness. Two types of DS-TOPCon cell architectures can be fabricated: i) full-area thin (≈40nm) n-TOPCon layer on the front and ii) selective-area thick (≈200nm) n-TOPCon fingers underneath the metal grid. Device simulations suggest that full-area DS-TOPCon cell with 40 nm n + poly-Si and selective-area DS-TOPCon cell with 200 nm n + poly fingers on the front, fabricated from our current DS-TOPCon cell precursor, can achieve cell efficiencies of 22.1 and 23.5%, respectively. Detailed power loss analysis and device simulation reveal that further improvements in material and device parameters have potential to push the cell efficiencies of DS-TOPCon cell structure beyond 25%, making it a promising alternative to fabricate a high-efficiency next-generation solar cells at low cost.
14 SOLAR ENERGY↗
Development and Reliability of Screen-Printable Fire-Through Cu Paste for Passivated Contact Solar Cells
We present the development of copper (Cu) paste which has been screen printed on Selective Emitter-Passivated Emitter Rear Contact (SE-PERC) solar cells. This paste can also be applied to Tunnel Oxide Passivated Contact (TOPCON) solar cells due to its fire-through nature. Champion PERC cells have achieved ....efficiency with ...parameters . Accelerated testing to investigate reliability performance of the SE- PERC mini-modules were carried out in damp heat chamber with 85oC and 85% humidity. The devices were found to be operational even after 1,500 hours. Devices with screen printed Ag contacts on the front side have been studied in parallel to the Cu contacts for comparison.
copper paste↗
Enhanced passivation and stability of negative charge injected SiN x with higher nitrogen content on the boron diffused surface of n-type Si solar cells
This paper explores the potential of the negatively charged SiN x using plasma charge injection technology to passivate the front textured boron-diffused emitter of n-type Si solar cells. The high-x value single SiN x layer with x ≥ 1.30 (x = N/Si) previously developed for the planarized rear-side passivation of p-type silicon solar cells, with an excellent passivation and charge stability, was found to be unacceptable for the passivation on the front textured boron emitter of n-type cells due to a severe bulk lifetime degradation issue. Therefore, in this study, we investigated a new concept of depositing a dual-x SiN x with a low-x SiN x layer (x~1.01) on top of a high-x SiN x layer (x~1.30) for passivation of the front textured rough surface of boron diffused emitter in n-type cells. Here, the optimized dual-x SiN x stack reveals the promise of charge retention for more than 25 years in field operation as well as excellent passivation of boron-doped emitter without bulk lifetime degradation. N-type cells with the optimized dual-x SiN x after charge injection show comparable cell performance to Al 2 O 3 passivated reference cells. The results of cell-level light stability tests using one-cell minimodules exhibit cell performance decay characteristics similar to the traditional Al 2 O 3 /SiN x passivated reference module.
14 SOLAR ENERGY↗
Novel Process for Screen-Printed Selective Area Front Polysilicon Contacts for TOPCon Cells Using Laser Oxidation
The efficiency potential of double-side tunnel oxide passivated contact (DS-TOPCon) solar cells is limited by parasitic absorption in the front poly-Si layer, despite excellent passivation and high V OC . The use of patterned poly-Si only under the front metal grid lines can significantly reduce the parasitic absorption loss without sacrificing voltage. In this work, we demonstrate a simple, manufacturing-friendly method of patterning the front poly-Si using a nanosecond UV (355 nm) laser. We found that with laser powers ≥3 W at a 400 mm/s scan speed, an estimated 1–4 nm thick stoichiometric SiO 2 layer was grown on TOPCon. This served as a mask for KOH-etching of 200 nm poly-Si, allowing for patterning of poly-Si fingers required for selective TOPCon. While laser powers above 3 W caused substantial deterioration in passivation quality, the resulting damage in J 0 was largely recovered by subsequent PECVD SiN x deposition. At 3 W, the full area J 0 was found to be 36.8 fA·cm –2 . Furthermore, this translates to 1.68 fA·cm –2 for 4.48% coverage from the wing area of the polyfinger lines (100 lines–100 μm wide and 30 μm metal) contributing to a total front J 0 of ~10 fA·cm –2 , well suited for 25% efficient solar cells
42 ENGINEERING↗
Pushing the efficiency limit of low-cost, industrially relevant Si solar cells to > 22.5% by advancing cell structures and technology innovations (Final Report)
The overall objective of this program is to achieve ~23% bifacial n-type cell efficiencies by developing and implementing optimized homogeneous or selective boron (B) emitter on front and tunnel oxide passivated contact (TOPCon) on rear side, in combination with advanced fine-line screen-printing metallization with floating busbars. During this research project, first we developed a technology roadmap to drive the 21% n-PERT cell efficiency from 21% to 23% by transforming the cell design to n-TOPCon and establishing the requirements for each layer, including B emitter, rear n-TOPCon, n-base Si and screen-printed contacts. Next, consistent with our roadmap, we developed advanced homogeneous implanted B emitter (150-180 Ω/⌫) passivated with ALD Al 2 O 3 layer capped with PECVD SiN x /SiO x double-layer antireflection coating This gave a very low recombination current density of 10-15 fA/cm 2 prior to metallization. In addition, we demonstrated metallized recombination current density of ~31 fA/cm 2 for this advanced homogeneous B emitter with industrial screen-printed, fire-through contacts with 40 μm wide grid lines, floating busbars and implementation of an advanced Ag-Al paste which resulted in local or reduced area metal-Si contact under the grid lines with virtually no emitter surface etching. This paste reduced the full area metallized J oe,metal from >1100 fA/cm 2 to ~700 fA/cm 2 . We also developed novel processes for the formation of p + /p ++ selective B emitter by a) single B diffusion with selective etch back and b) two-steps diffusion with implanted B in field region and APCVD B diffusion under the metal grid. We achieved very low un-metallized recombination current density (J 0 ) of ~18 fA/cm 2 for the selective p ++ p + emitters (30/150 Ω/⌫) and metallized J 0 of ~28 fA/cm 2 with ~3% screen-printed metal contact to p ++ regions. Next, we developed the technology for n-TOPCon by growing phosphorus-doped LPCVD and PECVD poly-Si on top of ~ 15Å chemically grown (NAO) tunnel oxide. After an optimized anneal at 875 °C for 30 min, passivated n-TOPCon have unmetallized J 0 of ~ 5 fA/cm 2 which went down further to ~ 1 fA/cm 2 after a 700 Å SiN x capping layer and simulated contact firing cycle at 770 °C. After screen-printed fire-through metallization on this n-TOPCon with ~13% metal coverage, metallized J 0 value increased to only ~5 fA/cm 2 which is among the lowest reported value to the best of our knowledge for screen-printed metallization. Finally, we integrated all the above technology innovations and enhancements and demonstrated low-cost manufacturable screen-printed n-TOPCon bifacial Si solar cell with ~23% efficiencies. Based on the experimental and theoretical understanding developed in this project, we have developed a new technology roadmap that shows that implementation of busbarless contacts, 10-20 ms bulk lifetime Si, and selective B emitter or selective TOPCon on the front can drive ~23% efficient cells achieved in this research to ~25% at low-cost.
14 SOLAR ENERGY↗