Search NASA⌕ Search

SEARCH · Search NASA

Results for “solid oxide electrolysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

A stable high-humidity bubbler design to supply steam for solid oxide electrolysis cells

A stable steam supply is required for the operation of solid oxide electrolysis cells. Heated water bubblers are the most common method due to the simplicity and inherent safety of the method, however, several design challenges hinder effective implementation. Here, a stable and validated bubbler design is presented, capable of achieving very high steam concentrations, relatively high flow rates, and continuous operation. A piping and instrumentation diagram and bill of materials are provided to enable easy duplication. Critical design parameters are discussed, including safety considerations and materials requirements, which are applicable to any bubbler design. The practical implementation of bubblers is also presented, including methods to prevent condensation instability and reduce backpressure to achieve a stable steam supply. The 3″ x 6″ (7.6 cm × 15.2 cm) bubbler achieves up to 98% steam balance hydrogen at 200 sccm and up to 1 slpm at 96% steam.

08 - HYDROGEN↗
DOE OSTI2023

Optimization of metal-supported solid oxide electrolysis cells with infiltrated catalysts

We report metal-supported solid oxide electrolysis cells (MS-SOECs) are being developed for steam-to-hydrogen electrolysis, especially for utilization of dynamic or intermittent electrical power from renewable sources. Various aspects of the electrocatalyst processing and composition, and metal support structure were explored. Catalyst materials, infiltration temperature and infiltration cycles were optimized for high performance and durability. Numerous catalyst materials were screened for both oxygen and steam electrodes. The oxygen catalyst had moderate impact on both initial cell performance and durability. Reducing Ni content in the steam electrode had little effect on durability, but reduced initial performance. Ex-situ XRD analysis and cell assessment of catalyst infiltration temperature revealed that the optimal range is 750–850 °C. The best cell performance and durability was achieved with LSCF-SDC oxygen electrocatalyst and SDC-Ni (60:40 vol%) steam electrocatalyst infiltrated 11 times at 800 °C and operated at 700 °C. At low steam content, a significant mass transport limitation on the steam side results in limiting current behavior. Thinner and more porous metal supports were implemented, and found to improve steam mass transport at low steam content, relevant for SOECs operating under high H 2 recycle rate or high steam utilization.

08 HYDROGEN↗
DOE OSTI2025

Cost analysis of alternative large-scale high-temperature solid oxide electrolysis hydrogen production facilities

We extend our past cost analysis of gigawatt-scale solid oxide electrolysis (SOE) facilities that produce high purity hydrogen gas from water by estimating construction and operating costs for three new alternative design cases: (1) offsite feed steam generation; (2) near-atmospheric pressure (NAP) stack; and (3) onsite electric boiler feed steam generation. Pressure effects on hydrogen electrode-(cathode-)supported SOE cell (SOEC) stack performance are estimated for the same assumed cell and stack construction and used to determine facility-wide stack capital costs for achieving a fixed H2 production at different pressures. Modular balance of plant (BOP) process equipment capital costs are estimated for each new alternative design case using our past equipment sizing, design, and cost data and scaling relationships. Furthermore, we update BOP equipment sizing and design for the NAP case using Aspen®. Vendor quotes for electric boilers are used to estimate costs for the electric boiler design case. Factory and onsite assembly and installation costs for SOEC stacks and BOP equipment are calculated using our past simplified first-principles approach. First-of-a-kind (FOAK) and N th -of-a-kind (NOAK) production maturity cost estimates are included for all results. The case with NAP stacks offers the lowest facility total capital cost (TCC, ~23% lower than base) while use of small electric boilers requires the highest TCC (~3% higher than base). H 2 production prices decrease from the base of ~$\$2.17$ /kgH 2 to ~$\$1.92$/kgH 2 for 1 GW e DC SIP facilities utilizing NAP stacks supplied by offsites steam situated in large modules and blocks for $\$0.030$/kWh e and $0.009/kWh t prices for electricity and thermal energy, respectively. We report all costs in 2021 US dollars.

Balance of plant (BOP) process equipment↗
DOE OSTI2020

Progress in metal-supported solid oxide electrolysis cells: A review

There is increasing global interest in using solid oxide electrochemical cells to perform electrolysis. Metal-supported solid oxide electrolysis cells (MS-SOEC) are being developed with stainless steel and Ni-based supports. Additionally, the use of porous metal to support the electrochemically-active layers is anticipated to improve mechanical strength, decrease cost, and increase tolerance to aggressive operating conditions, including rapid thermal excursions. This review summarizes and analyzes the previous decade of progress in MS-SOEC development, and identifies critical needs for future work.

08 HYDROGEN↗
DOE OSTI2025

Evaluation of a 5kW Solid Oxide Electrolysis Cell Stack

Electrolysis is the process of combining water and energy to produce oxygen and hydrogen gas. A solid oxide electrolysis cell (SOEC) is a type of high-temperature electrochemical cell used to yield hydrogen from steam. Many of these cells are put together to form an SOEC stack which operates between 600°C and 1000°C. There are several electrochemical methods for producing hydrogen, but the benefit of high-temperature electrolysis (HTE) in SOECs is they exhibit very high electrical efficiency and the potential for harnessing excess heat from other industrial processes such as nuclear power generation, fertilizer production, and chemical production.

08 - HYDROGEN↗
DOE OSTI2025

Current interrupt method for calculating the electrochemical impedance in a solid oxide electrolysis stack

Here, in this work the time domain response of Solid Oxide Electrolysis Cells (SOEC) to a current interruption was transformed into the frequency domain using a carrier function Laplace transform, which is fit to the experimental data using a MATLAB Complex Nonlinear Least Squares (CNLS) solver. The hardware implementation, consisting principally of a high-speed switch and a fast-logging Analog to Digital Converter (ADC), was assembled and tested using a calibration module to assess the accuracy, repeatability, and speed of acquisition of the prototype device as compared against a calibrated commercial impedance spectrometer. Additionally, the current interrupt device and commercial FRA were used to acquire the impedance spectra of a four cell SOEC stack with a large, 300 cm 2 , active cell area.

SOEC↗
DOE OSTI2024

Optimal operation of solid-oxide electrolysis cells considering long-term chemical degradation

Optimizing the performance of solid oxide electrolysis cells (SOECs) for long-term hydrogen (H 2 ) production at high temperatures is crucial, as prolonged operation leads to efficiency losses and shorter cell lifespans due to chemical degradation. Here, in this work, we adopt a quasi-steady state approach for dynamic optimization over extended operational periods to address the disparity in timescales between cell operation and degradation. Integrating a 2-D non-isothermal SOEC model with balance-of-plant (BOP) equipment, we explore three optimization objectives: minimizing terminal degradation, maximizing integral efficiency, and minimizing the levelized cost of H 2 (LCOH). Our dynamic optimization algorithm reduces LCOH by 9.5% and 16% compared to strategies focusing solely on terminal degradation and integral efficiency, respectively. For electricity prices of 0.03 $\$$/mWh and 0.3 $\$$ mWh optimal replacement schedules range from 5 to 2 years, depending on the operational mode. Furthermore, a flexible operational mode yields additional improvements in LCOH over traditional galvanostatic and potentiostatic modes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Life cycle analysis of a hydrogen production system based on solid oxide electrolysis cells integrated with different energy and wastewater sources

Hydrogen production via water electrolysis is a promising and evolving technology. The solid oxide electrolysis cell (SOEC) is one of the several technologies for this purpose. They are alternatives to the traditional hydrogen production from fossil fuels to enhance global energy decarbonization. However, in the bid for sustainability and a green economy, these technologies are not free from causing some environmental burdens. Using life cycle assessment (LCA), the greenhouse gas emission and degree of environmental impacts by these technologies can be identified and measured throughout their lifespan. This study addresses how to quantify these CO 2 emission impacts for an electrolytic system with different energy sources. The LCA of a novel integrated hydrogen production SOEC system with energy from solar photovoltaic and bituminous powerplant is performed using simaPro, the leading global LCA solution software. Measuring the environmental impact of the electrolytic operation in terms of weight, the bituminous powerplant poses damage which is, on average 700% more than solar PV. The thermal-to-hydrogen efficiency of the SOEC system is 56%, and a probable 28% reduction in carbon footprint with heat integration. The steam generation and the manufacturing of the SOEC have a very high environmental impact potential on the system. Here, we recommend LCA and net energy analysis is carried out for every new hydrogen technology and adequate comparison to enhance sustainable and green economy.

08 HYDROGEN↗
DOE OSTI2024

Modeling Oxygen Partial Pressure in Solid Oxide Electrolysis Cells: The Microstructure Effect

Oxygen partial pressure is an important thermodynamic state variable that affects both the performance and degradation of solid oxide electrolysis cells. In this work, a 3D model developed from Virkar’s 1D model has been applied to reconstructed and synthetic microstructures of Ni-YSZ-GDC-LSCF cell. The effect of the microstructures, including the thickness of the YSZ and GDC layer, and the compositions of the hydrogen and oxygen electrode, on the distribution of oxygen partial pressure has been investigated. The results show that the maximum oxygen partial pressure may occur on the interface between oxygen electrode and GDC layer or between GDC layer and YSZ layer depending on the rate of oxygen ion exchange between GDC and YSZ. A thicker GDC layer lowers the maximum oxygen partial pressure in the cell, while a thicker YSZ layer lowers the maximum oxygen partial pressure in the hydrogen electrode. In addition, the Ni:YSZ ratio and porosity also affects the maximum partial pressure. These findings provide insights on mitigating degradation in solid oxide electrolysis cell by tuning the microstructures.

Lei, Yinkai↗
DOE OSTI2024

Microstructure-Based Modeling of Inner Oxygen Pressure in Solid Oxide Electrolysis Cells

One major degradation mechanism during long-term operation of solid oxide electrolysis cells (SOECs) is delamination of oxygen electrodes (OEs). The driving force for the electrode delamination could be the generated high inner oxygen pressure near the electrode-electrolyte interface during operation. However, the effects of transport properties and electrode thickness on the inner oxygen partial pressure are not well understood. Here, a microstructure-based electrochemical model which includes the conduction of electrons and oxygen ions coupled with Butler-Volmer-type chemical reactions at triple-phase-boundaries (TPBs), is employed to investigate the oxygen pressure in lanthanum strontium manganate (LSM)-based SOECs. The model is applied to both two-dimensional (2D) prototype microstructures and three-dimensional (3D) realistic microstructures, and the oxygen pressure is analyzed as a function of transport properties and electrode thickness under both potentiostatic and galvanostatic operations. The simulation results suggest strategies to suppress electrode delamination. The simulation results are compared to an analytical solution, and the discrepancies are attributed to the Butler-Volmer-type kinetics included in the microstructure-based model.

Xue, Fei↗
DOE OSTI2020

On the role of the zirconia/ceria interface in the degradation of solid oxide electrolysis cells

Gd-doped Ceria (GDC) barrier layers are widely used in solid oxide electrolysis cells to prevent reactions between the Y-stabilized Zirconia (YSZ) electrolyte and oxygen electrode. In some cases, electrolysis operation causes fracture near the GDC/YSZ interface. Here, we explain this effect using a numerical calculation, showing that a peak oxygen pressure is observed near the GDC/YSZ interface during electrolysis operation. Moreover, GDC/YSZ interdiffusion and possible zirconate phase formation occurring during electrode firing yield a low oxygen ion conductivity region that introduces a much higher peak oxygen partial pressure at the interdiffusion layer/YSZ interface, thereby exacerbating degradation. The results indicate that the peak pressure can be reduced and, thereby, damage can be mitigated by altering processing in order to minimize interdiffusion, decreasing the GDC layer thickness, and reducing oxygen electrode polarization resistance or altering electrolyte transport properties, e.g., changing the Gd doping level of GDC to increase the oxygen vacancy diffusivity.

Physics↗
DOE OSTI2025

Ultra-high efficiency hydrogen production using a large-scale solid oxide electrolysis cell system

Efficient and cost-effective production of clean hydrogen is key to decarbonizing the production of hard-to-abate industries, such as chemicals, fuels, steel, cement and many other commodities that form the basis of modern societies. High-temperature steam electrolysis (HTSE) has recently become commercially available and offers opportunities for producing hydrogen at higher efficiency and lower cost than competing low temperature technologies. In this work, we report world record setting hydrogen production efficiency from large-scale prototype HTSE systems based on solid oxide electrolysis cell (SOEC) technology. Independent tests performed at Idaho National Laboratory (INL) employed a Bloom Energy 100 kW SOEC system to achieve a hydrogen production direct current specific electric energy consumption as low as 36.7 kWh per kilogram of hydrogen. Remarkably, similar high efficiencies in the range of 36–39 kW/kg-H2 were obtained over a wide range of hydrogen production rates and even during dynamic ramping as the hydrogen production and electric power consumption of the system were varied between 20 % and 100 % of nominal conditions. Furthermore, these test results validate previous projections that commercial SOEC systems can produce clean hydrogen at efficiencies approaching 100 % for less than 2 U S. dollars per kilogram when located near sources of inexpensive, low-grade heat and clean electricity.

08 HYDROGEN↗
DOE OSTI2025

Microstructure-based modeling of inner oxygen pressure in solid oxide electrolysis cells: Analysis of electrode delamination and mitigation

One major degradation mechanism during long-term operation of solid oxide electrolysis cells (SOECs) is delamination of oxygen electrodes (OEs). The driving force for the electrode delamination could be the generated high inner oxygen pressure near the electrode-electrolyte interface during operation. However, the effects of transport properties and electrode thickness on the inner oxygen partial pressure are not well understood. Here a microstructure-based electrochemical model, which includes the conduction of electrons and oxygen ions coupled with Butler-Volmer-type chemical reactions at triple-phase-boundaries (TPBs), is employed to investigate the oxygen pressure in lanthanum strontium manganate (LSM)-based SOECs. The model is applied to both two-dimensional (2D) prototype microstructures and three-dimensional (3D) realistic microstructures, and the oxygen pressure is analyzed as a function of transport properties and electrode thickness under both potentiostatic and galvanostatic operations. The simulation results suggest strategies to suppress electrode delamination. The simulation results are compared to an analytical solution, and the discrepancies are attributed to the Butler-Volmer-type kinetics included in the microstructure-based model.

25 ENERGY STORAGE↗
DOE OSTI2024

Dynamic operation of metal-supported solid oxide electrolysis cells

Symmetric-structure metal-supported solid oxide fuel cells and electrolysis cells (MS-SOFCs, MS-SOECs) offer several advantages over conventional solid oxide cells, including the use of inexpensive materials, high mechanical strength, and rapid ramp-up ability. Aggressive operation of MS-SOCs in fuel cell mode is well-established, including extremely fast start-up, redox tolerance, and imbalanced pressure. Here, we extend dynamic operation to MS-SOCs in SOEC mode with high steam content for both small button cells and a large rectangular cell, including: steam cycling, thermal cycling, redox cycling and power cycling. Steam cycling entailed switching between 3:97 and 50:50 steam:hydrogen ratio. For thermal cycling, the temperature was rapidly varied between 150°C and 700°C for 50 cycles. Redox cycling involved switching the steam side gas between 50 % humidified H 2 and 50 % humidified N 2 for 5 cycles. Power cycling was performed by operating the cell under variable current density, resulting in cell voltage between 1.3V and 2.8V. Degradation rates for each testing strategy were compared to a baseline cell, and found to be similar. In conclusion, the excellent tolerance to dynamic operation increases confidence that MS-SOECs will be compatible with dynamic or intermittent renewable resources.

08 HYDROGEN↗
DOE OSTI2023

Cost analysis of hydrogen production by high-temperature solid oxide electrolysis

In this study, we estimate construction and operation costs of gigawatt-scale solid oxide electrolysis (SOE) facilities for producing high purity hydrogen gas from water. Manufacturing and assembly costs for two types of SOE cell stacks are estimated using a detailed design for manufacture and assembly (DFMA®) analysis. Modular balance of plant (BOP) process equipment is designed and sized with Aspen®, and cost estimated using equipment vendor quotes. Factory and on-site assembly and installation costs for SOEC stack and BOP equipment integration into modular SOE process units are calculated using a simplified DFMA® method. Total stack costs on a stack input power (SIP) basis reduce to <$100/kW e DC SIP for >500 MW e DC SIP /year production rates with electrode cermet, interconnects, and high-temperature heat treatments dominating the total cost. Integration of stacks with larger BOP equipment operating at higher pressures offers ~36% cost reduction in total facility capital cost due to an economies of physical scale effect since BOP equipment comprises >50% of facility costs. Optimized H 2 prices decrease from ~$\$$4/kgH 2 to ~$\$$2/kgH 2 for 1 GWe DCSIP facilities using $\$$0.025/kWh electricity price. All costs are reported in 2021 US dollars.

08 HYDROGEN↗
DOE OSTI2026

The structure, composition, and performance impact of a YSZ-GDC interdiffusion layer in solid oxide electrolysis cells

This study provides a combined experimental and computational investigation into the structure and impact of the cation interdiffusion layer that appears at the gadolinium doped ceria (GDC)/yttria stabilized zirconia (YSZ) interface in solid oxide electrolysis cells (SOECs). Scanning transmission electron microscopy (STEM) illustrates that a ∼0.4 μm interdiffusion layer (IDL) with an intermixed cation distribution and fine grain size forms upon sintering. STEM identifies that the interdiffusion layer exists in the cubic fluorite structure despite changes in cation composition. The interdiffusion layer microstructure formed during sintering does not change during SOEC testing at either 1.3V or heightened voltage pulse testing. Modeling predicts that ionic conductivity may decrease in the interdiffusion layer due to Coulombic trapping between mobile oxygen vacancies and excess Gd 3+ acceptor dopants. Yet, the density and continuous nature of the layer should benefit cell stability by substantially reducing the formation of SrZrO 3 , which is corroborated by STEM and Synchrotron X-ray diffraction (XRD). We conclude that the interdiffusion layer acts as a beneficial barrier to Sr diffusion, when operating in a regime where electrolyte void formation is not observed.

organic↗
DOE OSTI2026

Enhancing Oxygen Evolution Reaction and Stability in Proton-Conducting Solid Oxide Electrolysis Cells (p-SOECs) via a Porous Gadolinium-Doped Ceria Interlayer

Proton-conducting solid oxide electrolysis cells (p-SOECs) offer a promising pathway for intermediate temperature (400-600 °C) hydrogen production. However, they still face critical challenges related to sluggish oxygen evolution reaction (OER) kinetics and low Faradaic efficiencies. Here, in this work, we demonstrate that introducing a thin (~0.8 µm) porous Gd 0.1 Ce 0.9 O 1.95 (GDC) interlayer between a BaCo 0.8 Zr 0.1 Zn 0.1 O 3-δ (BCZZ) oxygen electrode and electrolyte significantly enhances p-SOEC performance. The GDC interlayer reduces polarization resistance by 48% (0.54 to 0.28 O cm 2 ) and increases Faradaic efficiency from 63% to 81% at -0.8 A/cm 2 and 600 °C. GDC interlayer p-SOECs display elevated effective H 2 current densities compared to control p-SOECs and reach up to -1.22 A/cm 2 at 1.3 V. Mechanistic studies on the interactions between GDC and BCZZ reveal that GDC intrinsically promotes OER kinetics by significantly reducing the polarization activation energy (Ea p ), dropping from 1.45 to 1.22 eV for full p-SOECs and 0.98 to 0.76 eV for symmetric cells. This promotional effect is localized in the electrochemically active region near the electrolyte interface. Durability testing for over 1500 hours under 50% H 2 O conditions indicates that the GDC interlayer also improves long-term stability, with a degradation rate 53% lower than control p-SOECs. By pinpointing the interfacial region where GDC exerts its promotional effect, highlighting its role in enhancing OER kinetics, and establishing interlayer engineering as a powerful technique, this work provides a unified pathway to simultaneously improve p-SOEC activity, Faradaic efficiency, and durability.

08 - HYDROGEN↗