Search NASA⌕ Search

SEARCH · Search NASA

Results for “Fact of the week”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

1,724 records · Page 39
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Improving creep resistance of Al-0.27Zr-0.08Sn (wt%) via cold swaging while maintaining high electrical conductivity

This study investigates the effect of mechanical cold work (0, 50, and 90% cross-sectional area reduction via swaging) on the creep properties of cast aluminum alloys with high electrical conductivity including high-purity Al (HP-Al), Al-0.15Zr (Al-Zr), and Al-0.27Zr-0.08Sn (Al-Zr-Sn, wt%). The Al-Zr alloy is strengthened by Zr in solid solution while the Al-Zr-Sn alloy is additionally strengthened by Al3Zr nanoprecipitates (8 nm diameter). After 90% cold swaging, the alloys exhibit grains elongated along the swaging direction with their widths ranging between 8 and 152 μm perpendicular to the swaging direction. Creep testing at 200 °C shows that the minimum creep rate of all 90% swaged alloys shows high sensitivity to stress, which can be modeled via a threshold stress σth. Increasing swaging magnitude from 0 to 50 to 90% in Al-Zr-Sn improves the creep resistance without reducing electrical conductivity. The formation of subgrains, increased dislocation density, and columnar grain structure in swaged alloys all enhance creep resistance. HP-Al swaged to 90% exhibits much lower creep resistance (σth = 18 MPa) due to subgrain coarsening and the absence of precipitates compared to Al-Zr (σth = 40 MPa) and Al-Zr-Sn (σth = 40 MPa), which maintain stable subgrain structures and benefit from solid solution strengthening and Al3Zr nanoprecipitates, respectively. Although Al3Zr precipitates are known to stabilize the deformed microstructure by pinning grain-boundaries, this work demonstrates that Zr in solid solution alone can effectively stabilize the deformed microstructure resulting in enhanced creep resistance. This effect of Zr solute on stabilizing grain boundaries for creep performance was not previously well-defined in the literature. Despite similar creep performances of Al-Zr and Al-Zr-Sn, the latter shows 70% higher room-temperature microhardness and slightly improved electrical conductivity (56%IACS (International Annealed Copper Standard) vs. 57%IACS, respectively). This work provides new insights into creep mechanisms of cold-worked Al–Zr alloys that will guide the design of heat-resistant Al conductors for high-demand applications.

Coello ramirez, Ismael [Northwestern University,]↗
DOE OSTI2026

Monolayer Films of Binary Metal Oxide Nanoparticles for Carbon Nanotube Synthesis

Binary metal oxide nanoparticles (biMO-NPs) combining transition and main-group metals with well-organized atomic architectures have unique potential as robust and economical heterogeneous catalysts. Herein, metal oxide nanoparticles (CoAlxOy) using cobalt and aluminum were synthesized, and their structure, morphology, and chemical composition were investigated using various characterization techniques. The biMO-NPs, which had a Gaussian-type size distribution (∼6 nm), were assembled on plain silicon substrates modified chemically with linker molecules bearing suitable end groups. Surface analysis revealed an ordered, uniform, close-packed arrangement of biMO-NPs forming a monolayer architecture with nanoscale thickness (∼12 nm), high surface uniformity, and negligible defects. The nanoparticle monolayer film (NP-MF) was employed as a catalyst to grow carbon nanotube (CNT) forests via the thermal chemical vapor deposition (CVD) method, similar to those grown from catalyst thin films deposited by physical vapor deposition. Structural characterization confirmed the growth of a dense, uniform, high-quality vertically aligned carbon nanotube (VA-CNT) forest with a length of ∼125 µm, which is comparable to the VA-CNTs grown from expensive thin films. Thus, CNT growth was successfully catalyzed by the biMO-NPs, highlighting a simple and inexpensive alternative for catalyst deposition. In this innovative wet-chemistry approach, the catalyst and catalyst support are combined within a single nanoparticle before NP-MF assembly. Interestingly, this approach provides a scalable and cost-effective pathway for CNT growth, eliminating the need for expensive thin deposition techniques.

Regmi, Bishow [University of Cincinnati]↗
DOE OSTI2026

Reduced-order CFD modeling of cryogenic hydrogen isotope extrusion for pellet fueling

This study presents a reduced-order model (ROM) for computational fluid dynamics (CFD) simulations of cryogenic hydrogen isotope extrusions, focusing on protium (H₂) and deuterium (D₂) piston extruders. Using a 2D axisymmetric ROM in ANSYS-Polyflow, significant computational savings were achieved (runtime reduced from 9∼24 h to 3∼5 min), with extrusion force discrepancies between the 2D ROM and 3D models being on the order of 1%. Parametric studies identified optimal cutoff shear rates in the viscosity model (0.01/s for H₂ and 0.001/s for D₂), providing recommendations for future simulations. Finally, a comprehensive comparison of ROM results with experimental data was performed across varying geometries, cryogenic materials, temperatures, extrusion lengths, and piston velocities. Predictions at low extrusion temperatures met the objective of providing quick and efficient solutions with an acceptable extrusion force error of approximately 10% or less, validating the effectiveness of the 2D ROM approach. However, at high temperatures closer to the triple point, extrusion force error grows, which necessitates developing an improved model that accounts for temperature effects, e.g. melting. Nevertheless, the findings still represent a significant improvement in efficiency of CFD modeling of cryogenic hydrogenic extrusion. The ROM framework can also be extended to tritium (T2) and screw extruders, which will ultimately provide a fast and effective tool for optimizing pellet injector design for ITER and future reactor systems.

Fan, Joy [ORNL] (ORCID:0000000229751735)↗
DOE OSTI2023

High Sulfur Loading and Capacity Retention in Bilayer Garnet Sulfurized‐Polyacrylonitrile/Lithium‐Metal Batteries with Gel Polymer Electrolytes

The cubic‐garnet (Li 7 La 3 Zr 2 O 12 , LLZO) lithium–sulfur battery shows great promise in the pursuit of achieving high energy densities. The sulfur used in the cathodes is abundant, inexpensive, and possesses high specific capacity. In addition, LLZO displays excellent chemical stability with Li metal; however, the instabilities in the sulfur cathode/LLZO interface can lead to performance degradation that limits the development of these batteries. Therefore, it is critical to resolve these interfacial challenges to achieve stable cycling. Here, an innovative gel polymer buffer layer to stabilize the sulfur cathode/LLZO interface is created. Employing a thin bilayer LLZO (dense/porous) architecture as a solid electrolyte and significantly high sulfur loading of 5.2 mg cm −2 , stable cycling is achieved with a high initial discharge capacity of 1542 mAh g −1 (discharge current density of 0.87 mA cm −2 ) and an average discharge capacity of 1218 mAh g −1 (discharge current density of 1.74 mA cm −2 ) with 80% capacity retention over 265 cycles, at room temperature (22 °C) and without applied pressure. Achieving such stability with high sulfur loading is a major step in the development of potentially commercial garnet lithium–sulfur batteries.

25 ENERGY STORAGE↗
DOE OSTI2026

Electrochemical Deconstruction of Ortho-Phthalate Plasticizers and Recovery of Plasticizing Moieties

Electrochemical methods for the direct reduction of alkyl esters have been understudied but provide a potential advantage for addressing specific waste streams given that such strategies often require only a minimal chemical profile. One such waste stream that could benefit from electrochemical remediation is poly(vinyl chloride) (PVC) plastics. PVC recycling often faces challenges due to the complexity of such waste. Solvent-based recycling methods pose several advantages for addressing post-use PVC; however, such methods are complicated by the high amounts of toxic legacy plasticizers (ortho-phthalates) present in PVC. A potential solution to addressing such phthalates is to address them electrochemically, coupled with recovery of the resulting valuable products. Presented herein is an optimized electrochemical method for ester activation that is leveraged to separate and recover the aromatic and alkyl components of ortho-phthalate plasticizers. The resulting aliphatic alcohols may be reused to prepare other non-toxic plasticizers. This electro-degradation method is demonstrated on six phthalates that have been identified to pose health concerns in addition to plasticizers recovered from commercial samples of PVC.

di-(2-ethylhexyl) phthalate↗
DOE OSTI2025

Dimensional Evolution Guides Property Control in the A n Cu 4– n TiS 4 Semiconductor Series

Through progressive reduction of the three-dimensional (3D) covalent network of Cu 4 TiS 4 , we isolate seven new members of the A n Cu 4–n TiS 4 family (A = alkali metal; n = 0–4), spanning 3D, 2D, 1D, and 0D structural fragments. The dimensional reduction is rational, as it preserves the edge-sharing connectivity between [CuS 4 ] 7– and [TiS 4 ] 4– tetrahedra across the series. This structural evolution is driven by the stepwise substitution of Cu with alkali metals, guiding the formation of fragments with reduced dimensionality. The effects of “n” and “A” on the crystal structures, stabilities, electronic structures, and optoelectronic properties are profound, demonstrating that the manipulation of alkali metal size and A n Cu 4–n TiS 4 stoichiometry enables predictable variations in structure and properties. For example, the n = 0 and n = 4 end members of the A n Cu 4–n TiS 4 family set the range of achievable band gaps with 2.00 eV for Cu 4 TiS 4 , 2.60 eV for Na 4 TiS 4 , and intermediate values for the n = 1–3 members. Notably, CsCu 3 TiS 4 exhibits exceptional air stability and congruent melting, with density functional theory (DFT) calculating moderate hole and electron effective masses in specific crystallographic directions (mh = 1.24m 0 , me = 0.87m 0 ). Additionally, A 3 CuTiS 4 (A = Na, K, Rb) displays direct band gap behavior and long photoluminescence lifetimes of 2.3–8.6 μs, and K 3 CuTiS 4 has a PLQY of 5.19%. These findings underscore the potential of the A n Cu 4–n TiS 4 family for applications in optoelectronics and demonstrate widely applicable design concepts that unveil rational stoichiometries within a given composition space to generate a series of crystal structures related through an evolving covalent dimensionality that corresponds to a predictable electronic structure and property progression.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

A New Shutdown Dose Rate Benchmark Problem for Representative Fusion Applications

Here, this work introduces a new benchmark problem for calculating shutdown dose rates (SDDRs) aimed at fusion reactor applications. The model is designed to represent a simplified version of a typical ITER port plug. The responses of interest include neutron flux, gamma flux, and gamma SDDR at 12 different locations scattered throughout the port. This article outlines the geometry specifications of the problem, provides material definitions for the components, specifies the required responses to be calculated, and presents the source definition information. The need for this benchmark arises from the limited availability of publicly accessible references, with only one benchmark representing the typical dimensions and materials found in fusion systems. This existing benchmark has been cited extensively, reflecting the demand within the scientific community to test both established and novel workflows for SDDR calculations. However, since its presentation at a conference in 2011, the results have become increasingly well known. Moreover, the absence of formal publication and peer review has led to the details of this benchmark being extracted from secondary sources, such as subsequent studies that reference it. As a result, analysts are left with significant flexibility in interpreting the key parameters, which can be adjusted to account for unknown systematic errors, ultimately reproducing the already well-known responses. This new benchmark serves as an updated version of that earlier work, with the aim of providing a more reliable description of the materials and their impurities, which is crucial for assessing activation and subsequent gamma emission. Additionally, it seeks to provide a geometry that more closely represents an ITER port plug. The improvements in the problem definition will lead to a more reproducible benchmark problem, while also presenting the radiation transport community with a completely new challenge. The results will be published in a future article to allow analysts adequate time to analyze this problem independently.

Benchmark↗
DOE OSTI2026

Emissivity measurements of CuCrZr alloy

The Facility for Rare Isotope Beams (FRIB) heavy-ion accelerator, in user operation since 2022, produces rare isotope beams via interactions of high-intensity stable ion beams with a graphite production target. Approximately 20–40% of the primary beam power is deposited in the target, while the remaining 60–80% is absorbed by the beam dump. The minichannel beam dump (MCBD), currently operated at 20 kW and designed for operation up to 50 kW, uses CuCrZr alloy absorber plates. Thermal validation and thermal cycling tests of the MCBD were conducted at the Applied Research Laboratory (ARL) at Pennsylvania State University. Temperature measurements were obtained from an infrared (IR) camera. Since accurate temperature determination requires reliable emissivity values, the emissivity of CuCrZr was measured using the IR camera validated against thermocouple reference temperatures up to approximately 650 °C. The measurements were conducted under a vacuum level of approximately 10 -5 torr to minimize emissivity variations due to surface oxidation. The emissivity of CuCrZr was determined to be 0.057 ± 0.009 using a constant fit to the measured data over the surface temperature range from 100–650 °C.

Accelerator Subsystems and Technologies↗
DOE OSTI2026

Characterization of lateral amorphous selenium photodetectors for low-photon and VUV detection at cryogenic temperatures

The performance of amorphous selenium (a-Se) as a cryogenic photodetector material is evaluated through a series of experiments using laterally structured devices operated in a custom optical test stand. These studies investigate the response of a-Se detectors to low-photon fluxes at high electric fields near avalanche conditions, the linearity of the photoconductive response over a wide dynamic range and the direct detection of narrowband 130 nm vacuum ultraviolet (VUV) illumination. At 87 K, matched-filter analysis shows reliable single-shot detection with efficiencies ≥80% and area under the curve (AUC) ≥ 0.85 using as few as ∼ 6800 incident 401 nm photons, corresponding to ∼ 3400 photons within field-active regions after accounting for geometric constraints. Measurements are performed at cryogenic temperatures using calibrated photon fluxes derived from a silicon photomultiplier reference and a characterized optical filter stack. Additional experiments using a tellurium-doped a-Se (a-SeTe) device explore the material's behavior under identical test conditions and demonstrate that avalanche is achievable in a-SeTe at cryogenic temperatures. The results demonstrate reproducible low-noise operation, VUV sensitivity and field-dependent gain behavior in a lateral a-Se architecture, representing the first reported observation of avalanche multiplication in laterally structured a-Se and a-SeTe devices at cryogenic temperatures. These findings support the potential integration of laterally structured a-Se devices into next-generation pixelated liquid-argon time projection chambers (TPCs) requiring scalable, high-field-compatible photon detection systems.

Amorphous selenium↗
DOE OSTI2024

Molecules to Masterpieces: Bridging Materials Science and the Arts

Art and materials innovation have always been intertwined, dating back to the earliest human creations. In modern times, however, the increasing specialization of materials science often restricts artists' access to cutting-edge materials. Here, the materials science aspects of an art-science collaboration between artist Kimsooja and the Wiesner Lab at Cornell University, are detailed. The project involves the development of a custom-made iridescent block copolymer coating by means of self-assembly, originally applied to transparent window panels of a façade for the ≈14 m tall art installation: A Needle Woman: Galaxy Is a Memory, Earth is a Souvenir by artist Kimsooja. After several exhibitions in the US and Europe, the installation is now part of the permanent museum collection at Yorkshire Sculpture Park in Wakefield, UK. Full characterization of the solution blade-cast coatings show shear aligned, standing up lamellar morphologies that behave as volume-phase gratings with periodicities between 300 and 400 nm. Coatings are also applied to foldable (origami) paper and converted into iridescent porous ceramic materials. Furthermore, it is hoped this work inspires and informs communities across materials science, the arts, and architecture.

Architectural nanomaterials↗
DOE OSTI2026

Conformational Isomerization of Imide Anions Governs Solvation and Transport in Water-in-Salt Electrolytes

The behavior of highly concentrated electrolytes departs radically from the dilute-solution theory, yet the molecular origin of this transformation remains unresolved. Here, we identify the conformational isomerization of molecular ions as a decisive, previously unrecognized control parameter governing structure and transport in crowded aqueous electrolytes. Across a series of fluorosulfonimide anions, we show that increasing concentration drives a collective shift from extended transoid to compact cisoid conformers, revealed by small-angle X-ray scattering, vibrational spectroscopy, pulsed-field gradient NMR, and molecular dynamics simulations. This conformational transition triggers a collapse of the hydrogen-bonded water network and the emergence of densely packed ionic domains with confined water, producing a qualitative change in Li+ transport from solvent-mediated diffusion to network-confined hopping. Anion size and asymmetry systematically tune the onset of this transition, demonstrating that molecular geometry dictates mesoscale organization and dynamics in the ion-rich regime. Our results establish ion conformation, not merely composition or coordination, as a fundamental thermodynamic variable in concentrated solutions, providing a chemical framework that unifies solvation structure and transport in water-in-salt electrolytes and suggesting new principles for designing dense ionic media.

Nguyen, Huong TD↗
DOE OSTI2025

Electrochemical Behavior of Cerium at an Indium Tin-Doped Oxide Electrode in Acidic Media

The redox behavior and speciation of cerium at mesoporous thin films composed of nanoparticles of indium tin-doped oxide (nITO) electrodes were characterized in pH 4.8, 0.1 M acetate buffer and both 0.1 and 1 M HNO 3 using electrochemical techniques and X-ray photoelectron spectroscopy. Anodic deposition of ceria species from Ce(III) to the nITO electrode was achieved under all solvent conditions via spontaneous condensation of electrochemically generated ceric hydroxide species. In 1 M nitric acid, the rate of CeO 2 dissolution is on the same order as CeO 2 deposition, resulting in negligible amounts of CeO 2 electrodeposited at the nITO surface. The cathodic stripping of CeO 2 from the nITO substrate deposited in 0.1 M nitric acid or pH 4.8 acetate buffer follows a 2-step process where Ce(IV)-oxide is initially reduced to an unstable Ce(III)-oxide species that rapidly undergoes acid catalyzed dissolution to yield soluble Ce(III) (aq) . These findings provide a foundation for the pH and anodic potential controlled deposition of CeO 2 thin films to ITO substrates, which can aid in the development of materials composed of ceria. As a result, they can also be used to infer likely analogous actinide redox behavior and speciation at these electrodes.

Cerium↗
DOE OSTI2025

Quasicrystal stability and nucleation kinetics from density functional theory

The aperiodic order of quasicrystals bridges the amorphous and crystalline regime, so it has remained unclear whether quasicrystals are metastable or stable phases of matter. Density functional theory is often used to evaluate thermodynamic stability, but quasicrystals are long-range aperiodic and their energies cannot be calculated using conventional ab initio methods. Here, in this work, we perform first-principles calculations on quasicrystal nanoparticles of increasing size, from which we can directly extrapolate their bulk and surface energies. Using this technique, we determine with high confidence that the icosahedral quasicrystals ScZn 7.33 and YbCd 5.7 are ground-state phases, thus revealing that translational symmetry is not a necessary condition for the zero-temperature stability of inorganic solids. Although we found the ScZn 7.33 quasicrystal to be thermodynamically stable, we show on a mixed thermodynamic and kinetic phase diagram that its solidification from the melt is limited by nucleation, which illustrates why even stable materials may be kinetically challenging to grow. Our techniques broadly open the door to first-principles investigations into the structure–bonding–stability relationships of aperiodic materials.

density functional theory↗
DOE OSTI2026

Effect of Thermodynamic and Environmental Factors on Crystallization of DNA‐Origami Superlattices

The directed self‐assembly of nanoscale materials into ordered superlattices presents a powerful strategy for creating next‐generation materials with programmable mechanical, optical, and photonic properties. Deoxyribonucleic acid (DNA) origami has emerged as a versatile scaffold for encoding nanoscale geometry and guiding the crystallization of complex 3D architectures. However, a systematic understanding of the parameters that govern the efficiency and quality of superlattice formation remains limited. In this study, we utilize octahedral DNA nanoscale frames as a model system to investigate the relative influence of key factors, including buffer composition, ionic strength, frame concentration, and thermal annealing protocols, on the size, order, and reproducibility of the resulting superlattices. Our findings provide a quantitative framework to rationally optimize DNA‐based assembly pathways. Structural characterization via small‐angle x‐ray scattering (SAXS), scanning electron microscopy (SEM), and optical microscopy validates the quality and fidelity of the assembled lattices. Moreover, by templating these DNA frameworks into inorganic replicas, we establish general design principles that extend beyond biomolecular systems, providing a foundation for the synthesis of programmable materials in broader nanofabrication contexts.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2023

Polycarbonate‐Based Solid‐Polymer Electrolytes for Solid‐State Sodium Batteries

Solid-polymer electrolytes comprised of polypropylene carbonate (PPC) and varied sodium bis(fluorosulfonyl)imide (NaFSI) salt concentrations are investigated for implementation as a conductive solid polymer electrolyte into solid-state cathode composites utilizing a sodium-layered oxide active material. The ionic conductivity generally increases with NaFSI salt content, reaching ≈1 mS cm −1 at 80 °C at the highest salt concentration (PPC:NaFSI = 0.5:1). Through an all-in-one slurry casting method, Na 2/3 Ni 1/3 Mn 2/3 O 2 cathode composites are fabricated in which the dispersed PPC electrolyte acts as the primary binder. Enabled by a bilayer polymer electrolyte system, cycling performance with the PPC cathode electrolyte is optimized with respect to salt concentration and anode material. The best cyclability is achieved with a moderate salt concentration electrolyte (PPC:NaFSI = 5:1), showcasing an initial capacity of 83 mA h g −1 with a remarkable 80% capacity retention after 150 cycles at C/5 rate and 60 °C. The superior performance of the lower salt concentration electrolyte is attributed to better electrochemical stability, as confirmed by linear sweep voltammetry and online electrochemical mass spectrometry measurements. In conclusion, these results underscore the potential of carbonate-based polymer electrolytes and the importance of balancing electrolyte conductivity and stability in cell design.

25 ENERGY STORAGE↗
DOE OSTI2026

Weak, shallow, dry convection over Angola increases offshore stratocumulus cloud droplet number concentrations

Boundary-layer cloud interactions involving shortwave-absorbing aerosols remain one of the least understood aerosol influences on climate. Here, we find the highest stratocumulus cloud droplet number concentrations over the southeast Atlantic occur when agricultural fires coincide with synoptically-weakened surface warming over Angola, occurring June-early August. Dry convection fills a shallow continental boundary layer with smoke, and a nighttime (local solar time 2-9) land breeze transports the aerosol into the marine boundary layer. Offshore aerosol transport is strengthened by low-level easterlies from a continental pressure high southeast of Angola. Simultaneously, the South Atlantic subtropical high is weaker, allowing extensive dispersal of aerosol offshore into the boundary layer, obscuring cloud brightening from shipping. Meteorological co-variation at synoptic scales compensates for cloud brightening by the smoke. Outgoing shortwave radiation increases by 15–20% of the monthly mean in June and July when offshore droplet numbers are less but the stratocumulus deck is more developed.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2026

Characterization of Flashback and Flame-Holding in a Jet-in-Crossflow Mixing Configuration With Methane–Hydrogen Fuel Blends

An approach that combines experimental and numerical analyses has been implemented to characterize the fundamentals of flashback events and flame-holding phenomena during high-hydrogen combustion in a jet-in-crossflow (JICF) configuration. Such flame dynamics are visualized experimentally using nanosecond (ns)-based hydroxyl planar laser-induced fluorescence (OH-PLIF) and chemiluminescence diagnostics techniques. The JICF burner has an optically accessible premixing tube allowing the optical diagnostics. The testing was conducted for varied premixer velocities (V) and equivalence ratio (ϕ) for 90–100% (H 2 , by mole) H 2 /CH 4 reactant mixtures at atmospheric temperature and pressure conditions. Two distinct flashback events were identified – conventional rich flashback and lean flashback, recorded while increasing ϕ and decreasing ϕ, respectively. The cause of lean flashback was attributed to lower momentum flux ratio which bends the jet sharply, closer toward the injection plane. The mean OH-PLIF images characterized the flame-holding behavior, where the flame was found to be stabilized on the leeward side only or on both windward and leeward sides as a lifted flame near the fuel port. A large eddy simulation (LES) with detailed chemistry combustion modeling approach was implemented along with an OH* submechanism, and it showed qualitative agreement with the integrated line-of-sight chemiluminescence results as well as the planar OH-PLIF measurements.

chemiluminescence diagnostic↗
DOE OSTI2025

IBPSA Project 2 BOPTEST: An update on the test cases available in the framework for testing advanced control strategies in buildings

Project 2 develops software infrastructure, test cases, and extensions for the Building Optimization Testing Framework (BOPTEST) to address the expanding needs of building and urban energy system controls through open international collaboration. This paper provides an overview of the new test cases available as of BOPTEST version 0.7.1. Each test case is developed using open-source Modelica libraries and Spawn of EnergyPlus, enabling the creation of high-fidelity building models that incorporate envelope dynamics, Heating Ventilation and Air Conditioning (HVAC) systems, and explicit control representations. Currently, eight test cases are available, with five additional cases under development. These test cases cover a wide range of climates, building types, and HVAC systems. This paper compiles and summarizes test case descriptions, cites original manuscripts that developed them for a more detailed description, and reports baseline control performance metrics. Furthermore, two example applications are presented: one illustrating different levels of control, from supervisory to low-level, and another demonstrating how Model Predictive Control (MPC) solutions must be adapted from continuous to integer to control some building actuators.

Zanetti, Ettore↗