Search NASA⌕ Search

SEARCH · Search NASA

Results for “DIODE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 919 records · Page 51

High voltage power Schottky diodes

Calculations of the low frequency rectification efficiency of power Schottky diodes show that silicon Schottky rectifiers have lower losses than silicon p-n junctions for all voltage applications up to approximately 150 volts. These calculations are presented. Large area Schottky diodes have been fabricated which exhibit near ideal reverse leakage at 100 C out to approximately 100 volts and which have current capability of 100 A. Fabrication details and performance data are presented.

Cordes, L. F.↗

The Lockheed diode array magnetograph

A new magnetograph using a solid state monolithic linear silicon diode array has been constructed at Lockheed Solar Observatory. This magnetograph uses a digital image processor, and makes data available both in digital and analog form. The diode array detector is capable of a signal-to-noise ratio of 2000:1 or better when cooled to a temperature of -40 deg centigrade. Thus, intensity differences of the order of one part in a thousand may easily be detected without signal averaging. This instrument may be considered a prototype for an instrument using a two-dimensional array. The magnetograph is now fully operational, and is being used to produce data for statistical studies of solar magnetic field diffusion.

Smithson, R. C.↗

Research and development for improved lead-salt diode lasers

A substantial increase in output power levels for lead-salt diode lasers, through the development of improved fabrication methods, as demonstrated. The goal of 1 mW of CW, single-mode, single-ended power output, was achieved, with exceptional devices exhibiting values greater than 8 mW. It was found that the current tuning rate could be controlled by adjusting the p-n junction depth, allowing the tuning rate to be optimized for particular applications. An unexpected phenomenon was encountered when crystal composition was observed to be significantly altered by annealing at temperatures as low as 600 C; the composition was changed by transport of material through the vapor phase. This effect caused problems in obtaining diode lasers with the desired operating characteristics. It was discovered that the present packaging method introduces gross damaging effects in the laser crystal through pressure applied by the C-bend.

Butler, J. F.↗

Coupling characteristics of thin-film metal-oxide-metal diodes at 10.6 microns

Direct detection experiments have demonstrated the coherent coupling of 10.6 micrometer radiation into photolithographically fabricated metal-oxide-metal tunnel junctions. A CO2 laser beam mechanically chopped at 1 KHz was focused at a variable angle of incidence with a power density of about 10 W/sq cm at the diodes. Diodes in which the junction resistance was much greater than the lead resistance displayed angular characteristics dominated by coherent antenna coupling.

Wang, S. Y.↗

Diodes stabilize LED output

Small-signal diodes are placed in series with light-emitting diodes (LED's) to stabilize LED output against temperature fluctuations. Simple inexpensive method compensates for thermal fluctuations over a broad temperature range. Requiring few components, technique is particularly useful where circuit-board space is limited.

Deters, R. A.↗

Room-temperature-operation visible-emission semiconductor diode lasers

There were two main approaches taken to develop shorter wavelength lasers. (1) Based on (AlGa)As and liquid-phase epitaxy, significant new results were obtained: Properties of these laser diodes (power output, spectra, and beam patterns), materials considerations, laser theory, and growth problems are discussed. The design of (AlGa)As layers is discussed from the vertical point of view, and various design curves are given. Horizontal structural requirements are also discussed. Experimental results from measurements done as a function of hydrostatic pressure are correlated with other results. (2) The first heterojunction laser structures using GaAs sub l-x P sub x and In sub y Ga sub l-y P at compositions, where the lattice constants are matched, were grown using vapor-phase growth technology and are described in detail, including experimental device results. Threshold current densities from 3,000 to 5,000 A per sq cm. and emission wavelengths from 6,520 A to 6,640 A were obtained at 77 K. The limiting factor in these devices is nonradiative recombination at the heterojunctions. Life tests on facet-coated (AlGa)As CW diodes are reported.

Ladany, I.↗

A shock isolator for diode laser operation on a closed-cycle refrigerator

A device developed to isolate the diode laser from impact shocks delivered during the expansion phase of the Solvay cycle of a helium refrigerator is briefly described. The device uses intermediate cold stations in the stand-off, which permit the stand-off to be short and rigid while minimizing the thermal load at the diode mount.

Jennings, D. F.↗

Development of a thermal diode heat pipe for cryogenic applications

The paper describes the development of a cryogenic thermal diode heat pipe for space flight applications. The diode has ethane working fluid, and uses the liquid blockage technique with an internal blocking orifice, to accomplish shutoff in the reverse mode. The pipe is 0.635 cm OD by 75.82 cm long including a 2.54 cc excess liquid reservoir. Experimental data are presented for forward mode throughput vs tilt, film coefficients, and reverse mode characteristics. Transport capacity is 1000 w-cm at 2.5 cm tilt. Evaporator and condenser film coefficients were 0.92 and 1.64 w/sq cm K, respectively.

Quadrini, J. A.↗

High frequency capacitor-diode voltage multiplier dc-dc converter development

A power conditioner was developed which used a capacitor diode voltage multiplier to provide a high voltage without the use of a step-up transformer. The power conditioner delivered 1200 Vdc at 100 watts and was operated from a 120 Vdc line. The efficiency was in excess of 90 percent. The component weight was 197 grams. A modified boost-add circuit was used for the regulation. A short circuit protection circuit was used which turns off the drive circuit upon a fault condition, and recovers within 5 ms after removal of the short. High energy density polysulfone capacitors and high speed diodes were used in the multiplier circuit.

Kisch, J. J.↗

High resolution spectral measurement of the HNO3 11.3-micron band using tunable diode lasers

High resolution spectra in the region of the 2-nu9 band of nitric acid have been obtained for selected portions of the HNO3 spectrum using tunable diode laser techniques. Continuous spectra are presented from 891.25/cm to 898.77/cm, with a spectral resolution less than or equal to 0.001/cm (30 MHz). Absolute line intensities and line positions are presented. Absolute wavelength calibration was obtained by frequency mixing the diode laser with a C(13)O2(16) isotope laser. Self and foreign gas (N2) broadening coefficients were iteratively calculated from the experimental data and were determined.

Brockman, P.↗

MIS diode structure in As/+/ implanted CdS

Structure made by As implantation of carefully prepared high-conductivity CdS surfaces followed by Pt deposition and 450 C anneal display rectifying, although substantially different, I-V characteristics in the dark and during illumination with subband-gap light. Structures prepared in the same way on an unimplanted portion of the substrate have similar I-V characteristics, except that the forward turnover voltage for an illuminated unimplanted diode is much smaller than that for an implanted diode. It is suggested that the charge conduction in both structures is dominated by hole and/or electron tunneling through a metal-semiconductor potential barrier. The tunneling processes appear to be quite sensitive to subband-gap illumination, which causes the dramatic decreases of turnover voltages and apparent series resistances. The difference in turnover voltage appears to be caused by interface states between the Pt electrode and the implanted layer, which suggests a MIS model.

Hutchby, J. A.↗

Infrared vibration-rotation spectra of the ClO radical using tunable diode laser spectroscopy

Tunable diode laser spectroscopy is used to measure the infrared vibration-rotation spectra of the ClO radical. The radical is generated in a flow system where a Cl2-He mixture passes through a microwave discharge to dissociate the Cl2. An O3-O2 mixture from an ozone generator is injected into the system downstream of the microwave discharge where O3 combines with Cl to form ClO. By adjusting the gas flow rates to yield an excess of Cl atoms, all the ozone is combined. ClO concentration is measured with UV absorption at 2577 and 2772 A and a deuterium lamp as a continuous source. Total cell pressure is 5.5 torr. The diode laser spectrometer is calibrated with ammonia lines as a reference where possible. The frequency of vibration-rotation lines is expressed as a function of rotational quantum number, fundamental vibrational frequency, and the rotational constants of the upper and lower vibrational states.

Rogowski, R. S.↗

JANTX1N3893 diode

Diodes manufactured by Siemens and Motorola were tested. Testing of Motorola diodes was stopped in all 3 groups because 50% failure-rate limit was reached. Siemens lot endured more testing in groups 1 and 2 and completed testing on group 3. Failure analysis was performed for group 2 testing.

Source record↗

JANTX1N5415 diode

Tested diodes were manufactured by Semtech and Micro Semiconductor. Micro Semiconductor diodes experienced no failures in groups 2 and 3 testing and only four failures in group 1.

Source record↗

Diode step stress program, JANTX1N5614

The reliability of switching diode JANTX1N5614 was tested. The effect of power/temperature step stress on the diode was determined. Control sample units were maintained for verification of the electrical parametric testing. Results are reported.

Source record↗

JANTX1N5622 diode

Report describes effects of power and temperature overstress on Semtech and Micro Semiconductor diodes. Semtech devices failed with excessive reverse bias leakage due to external paint. Micro Semiconductor diodes had reverse bias leakage failure due to damaged silicon.

Source record↗

JANTX1N5623 switching diode

Report describes effects of power and temperature overstress on Semtech and Micro Semiconductor devices. Only two Semtech diodes failed catastrophically. Testing on Micro Semiconductor devices stopped because failure limit was reached. Micro diodes suffered lead separation.

Source record↗